Jump to content
SAU Community

Recommended Posts

My mate is putting a rb20det into his r33 just as a skid pig to learn to drift.

Now we have a r32 rb20det with loom and ecu.

Dash plug pins done match.

And square plug under airbox pins dont match. Need some advice to set this all up.

We cant even find any wiring info for the RB20e R33 to even begin to figure it out.

So any infomation would be good.

Or any tips to make it run with out it being wired to the car, more like its just sitting there to hold it.

And dont just say get a rb25... picked this motor up for $200 with a rebuilt head.

And getting this wired up will help when his RB30DET goes in as he has a R32 RB25 head. Cheers

Link to comment
https://www.sau.com.au/forums/topic/463046-r33-twin-cam-swap/
Share on other sites

done match? so you've done the matching

I believe you mean don't match.. both very different words with different meanings.

Because it'a R33, I would suggest investigating on a R33 GTS-t loom and swap the injector pins to suit. Then splice the sensor wires into the R32 sensors. Of course a RB20DET doesn't have VCT so you can just terminate those wires.

Not really rocket science, you'll work it out.

We got it running found some info from someone thats done the swap.

And regards to the comment about small tyres, I have a friend who drifts a single cam non turbo rb20e r32 and goes out with the big boys. A turbo twin cam rb20det will do just fine. The one problem I have with community is the hate towards RB20'S

fuel pump on switch idea isn't smart.

I would use the ECU to trigger your fuel pump, so when the motor isn't turning the pump stops.. good for when there's a crash, and a fuel line ruptures etc. and there's no fuel being pumped everywhere

Ok well I guess we will sort a new feed for that then, didnt think to far into it at this stage.

Ill have to look more into it because the normal power feed etc was somehow running 12v constant so the car would stay running with the key out as a turbo timer would act. So ill have to either get the ecu trigger to work, may wire up a relay using the ecu trigger and the 12v switched feed and get it going that way, either that or anything that only feeds 12v with the engine running haha. More investigation is needed for the next step... dont worry though guys his car is miles away from being ready to drive

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • For these last 7 years of ownership, I've always had to use a small scissor jack under one of the front tow hooks to raise the front just enough so my low-profile jack fits under to reach my subframe jack point. I'm beginning to get annoyed of always having to do this. Are there any lower low-profile jacks that fit under the gtr lip on a dropped car?
    • Seat of the pants assessment of the new intake: The car is way less "doughy" when hitting the loud pedal, especially off idle when stopped or in traffic, I did use a cheapo lazer thermal thingo to measure the temp around where the pod filter got its air, it was between 55 - 60°C, in saying this the car was shut off and not moving, so the OEM intake pipe was not supplying any fresh air to where the pod was when the car was at least moving A weird bonus was induction noise on the throttle in the cabin increased a bit,  I was worried that I was actually going to lose some of that induction noise I love so much, outside though, when I got the daughter to do a WOT drive by pass for me, the induction noise has increased alot when on the throttle, not quite ITB doort, but well up there I'm extremely happy with the results and have been exploring the country roads in the region  As for house mods: 1.New front fence is up and is awesome, it really upgraded how the joint looks from the street, and the added security is nice 2. Electricians have replace some interior lights, and with more lighting in the garage, a few new motion detecting lights out the front above the garage, front room, and at the front door, which I have already found heaps helpful coming and going, also now has fancy pants CCTV all round the house The only hold point for power though is the solar and batteries due to supply issues, although this will happen over the next few weeks 3. I have done a heap of landscaping out the front and I'm almost ready to do a new small retaining wall with some nice blocks to replace the brick and cemented in rocks around the raised garden beds cemented in river stone "was the fashion at the time" the house was built. I currently have a pallet of retaining wall blocks and 2 bulka bags of 20mm blue metal to replace the wood chip that is in the raised garden beds around the house 4. I now have 3 big raised garden beds for out the back to grow some vegetables, about 70cm high, 200cm long and 100cm wide 5. My 2 compost bins are already pretty full with brown, green and kitchen waste from the landscaping I'vedone so far, but they will probably take a few months to break down, so anything else that gets chopped, trimmed, and kitchen waste will just start filling the base of the raised garden beds to about 30cm before I start throwing 40cm of good compost, and stuff, for the vegetables to grow in, I'll need a few ton of compost and soil, but the local supplier can sent me bulka bags of the stuff Basically the logs, wood chips and a few strategically placed rocks for drainage, will give the beds some good organic materials down low to break down over time, and they will hold moisture during the warmer months to save the water in my big arse water tank if we don't get alot of rain So, all in all, the car and house mods are going well, and I'm really enjoying being retired, I sleep in too 0700 and slowly plod around inside until I feel like actually doing anything, and only work in the yard for as long as want, which has actually been alot over the last few weeks,  although when you look at it, it seems that not a huge amount of work has been done,  until I look at the before I started the work pics Happy days and good times indeed 
    • hahaha yeah. Plan is to get side skirts and probably just rear pods. But going to do them one-by-one. I've got a set that I really like from RHDJapen, but that one isn't shipped to AU. So need to find someone who can get it for me
    • Here's an idea, answer the questions I asked you as they are trying to work out WHY the LSD will be binding up in a straight line.
×
×
  • Create New...