Jump to content
SAU Community

Recommended Posts

I'm thinking about selling my 4" titanium cat back exhaust to suit r32 GTR

In very very good condition, very light, sounds amazing !

Previous owner said it was an amuse exhaust but can't see any markings

I'm in 2 minds about selling but if I get the price I want Ild let it go,

Also have a brand new 4" flange to suit exhaust so you can weld it to ur cat and everything bolts up 100%

Asking $1700, located in Sydney and can help with postage if need be (wrap it up and package it etc)

post-24984-0-02748500-1461917966_thumb.jpg

post-24984-0-69655100-1461918014_thumb.jpg

Edited by SiR_RB
  • Like 2

Pics of it on the car? 4inch inner or outer diameter?

considering titanium exhausts r only 1 or 2mm thick it would make zero difference
  • Like 1

Looks good but most jap titanium exhaust that I have seen including my own one have a lot more crab weld sections in the bends. Are you sure it's a jap exhaust?

I really need a 4" exhaust. How high does it sit up?

If i didnt already have a 3.5" Ti exhaust, i would snap this up in a heart beat!!!

I would say it would be pretty loud, as my one has 2 mufflers and still sounds loud and angry

  • 4 weeks later...

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • Yeah I've had too many issues with knock off's on the BMW's. I don't want to do a job twice or more because the parts are shit.
    • I read this and thought "ah! I will do this scissor jack on the tow point thing!" I just use my floor/low profile/costco jack and lift the car up by the tow hook itself, then slide jack stands under. Never thought about using scissor into floor jack combo :p
    • Well, my new WMI system took much longer to finalize. I actually missed my dyno appointment last Friday and lost my 150$ deposit. I'll be going back in the next week or two.  To sum it up. I only kept the AEM tank from my old setup. I replaced the AEM pump with a higher flow/pressure ProMeth 30GPH pump. I also swapped over to a 6AN low pressure feed line to the pump from the tank. There's also a pressure switch you cannot see on the pump high pressure line.    This is feeding 6x 200CC direct port nozzles and 1x 500CC Pre Throttle body nozzle. All fittings are Swagelok, because well why not. I also have a 300PSI pressure sensor up front.    I now have my Haltech ECU controlling everything. I start my pump with a basic relay at 5PSI and deadhead it. I then PWM a 3000CC methanol Injector to control flow starting around 10psi. The pressure switch in the trunk, along with my tank level are safeties before I ever get to 10PSI, and then I use my pressure sensor upfront as a secondary safety to cut the WMI and corrections in case the injector blocks or a line ruptures.  Wish me luck on the dyno!    
    • So, I'm back with bad news. There's no jack long enough on this planet that will reach the front subframe. If by some chance there is, it would weigh 200lb's.  I purchased a long reach jack... The damn thing weighted 120lb's and was massive. Didn't even come close, was still short at least a foot. It was a pain, but I brought it back. Next I decided HA! No problem, I'll get an Extra long reach jack. Well, I couldn't lift the box... It must have weighed 160LB's and luckily there was an open box in store. I took measurement and was still nowhere close.  Sadly I've lost hope and have accepted defeat. 
    • Thanks for that tip, niZmO_Man. I think the battery is OK. It's quite a new one, but I'll check. Last time I needed a new battery, everything electronic was fine, except that there wasn't enough current to turn over the starter. I decided to order one of the partial AV system translation CDs from Car Audio Workshop in NZ. That might have some effect, or help me diagnose the date problem. 🤞
×
×
  • Create New...