Jump to content
SAU Community

Recommended Posts

Message zoom on this forum, he's all over the WMI shit.

It explained to me what you do is get the afrs down to say 10.5 and inject, change nozzles blah blah with wmi till you lean it back up by 1 afr point, ie back to where you were before. Then advance the timing as you would with E85.

My lazy E85 blanket is 5 degrees at peak torque and about 7 up top. Then use a dyno to determine where on the curve you can improve.

He reckons WMI is on par with E85, however with wmi you lose off boost torque because you're not injecting it on vac (well you could).

  • Like 1

Message zoom on this forum, he's all over the WMI shit.

It explained to me what you do is get the afrs down to say 10.5 and inject, change nozzles blah blah with wmi till you lean it back up by 1 afr point, ie back to where you were before. Then advance the timing as you would with E85.

My lazy E85 blanket is 5 degrees at peak torque and about 7 up top. Then use a dyno to determine where on the curve you can improve.

He reckons WMI is on par with E85, however with wmi you lose off boost torque because you're not injecting it on vac (well you could).

Was explained to me in a similar way, change nozzles until your standard no wmi base afr is only richened by around 0.8afr with wmi and either tune it out if you have fail safe or leave it if not.

Not having much power under vac isn't a problem for us auto guys, always on boost when you're above 10% throttle.

The kits aren't cheap. If I can't get an extra 20-30kw under 4K I don't think it's worth it for me. But peak power, $500 for an extra 40-50kw is money well spent.

My tuner said he doesn't want to run more then 20 to be safe.

Maybe I could go e85 have a eflex sensor and do the 30 bottom end conversion.. If I go 30 bottom end would I need a bigger turbo it has a .67 rear it's the atr45 from hypergear 600hp rated ?

you would just get a a .82 housing of him, no need to get another turbo.

cheers

darren

Bigger cams will only move the power to the right on the graph. Yes there may be a tad more of it but you will loose a whole lot down low. Same goes for putting a different plenum on. So its a trade off. May be worth it, may not, depends on exactly what you want to do with the car.

Also note that if you upgrade to the wrong cams (generally anything massive) you will need to delete the VCT solenoid on the intake, which will also hurt low down torque and power. I think the HKS 256mm drop in does let you retain vct? (someone would have to confirm that) so that, or one tha tdoes, pretty much the only one you should realistically go with

Tomei make drop in where you can still use your VCT, or last time I looked they did.

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now



  • Similar Content

  • Latest Posts

    • For these last 7 years of ownership, I've always had to use a small scissor jack under one of the front tow hooks to raise the front just enough so my low-profile jack fits under to reach my subframe jack point. I'm beginning to get annoyed of always having to do this. Are there any lower low-profile jacks that fit under the gtr lip on a dropped car?
    • Seat of the pants assessment of the new intake: The car is way less "doughy" when hitting the loud pedal, especially off idle when stopped or in traffic, I did use a cheapo lazer thermal thingo to measure the temp around where the pod filter got its air, it was between 55 - 60°C, in saying this the car was shut off and not moving, so the OEM intake pipe was not supplying any fresh air to where the pod was when the car was at least moving A weird bonus was induction noise on the throttle in the cabin increased a bit,  I was worried that I was actually going to lose some of that induction noise I love so much, outside though, when I got the daughter to do a WOT drive by pass for me, the induction noise has increased alot when on the throttle, not quite ITB doort, but well up there I'm extremely happy with the results and have been exploring the country roads in the region  As for house mods: 1.New front fence is up and is awesome, it really upgraded how the joint looks from the street, and the added security is nice 2. Electricians have replace some interior lights, and with more lighting in the garage, a few new motion detecting lights out the front above the garage, front room, and at the front door, which I have already found heaps helpful coming and going, also now has fancy pants CCTV all round the house The only hold point for power though is the solar and batteries due to supply issues, although this will happen over the next few weeks 3. I have done a heap of landscaping out the front and I'm almost ready to do a new small retaining wall with some nice blocks to replace the brick and cemented in rocks around the raised garden beds cemented in river stone "was the fashion at the time" the house was built. I currently have a pallet of retaining wall blocks and 2 bulka bags of 20mm blue metal to replace the wood chip that is in the raised garden beds around the house 4. I now have 3 big raised garden beds for out the back to grow some vegetables, about 70cm high, 200cm long and 100cm wide 5. My 2 compost bins are already pretty full with brown, green and kitchen waste from the landscaping I'vedone so far, but they will probably take a few months to break down, so anything else that gets chopped, trimmed, and kitchen waste will just start filling the base of the raised garden beds to about 30cm before I start throwing 40cm of good compost, and stuff, for the vegetables to grow in, I'll need a few ton of compost and soil, but the local supplier can sent me bulka bags of the stuff Basically the logs, wood chips and a few strategically placed rocks for drainage, will give the beds some good organic materials down low to break down over time, and they will hold moisture during the warmer months to save the water in my big arse water tank if we don't get alot of rain So, all in all, the car and house mods are going well, and I'm really enjoying being retired, I sleep in too 0700 and slowly plod around inside until I feel like actually doing anything, and only work in the yard for as long as want, which has actually been alot over the last few weeks,  although when you look at it, it seems that not a huge amount of work has been done,  until I look at the before I started the work pics Happy days and good times indeed 
    • hahaha yeah. Plan is to get side skirts and probably just rear pods. But going to do them one-by-one. I've got a set that I really like from RHDJapen, but that one isn't shipped to AU. So need to find someone who can get it for me
    • Here's an idea, answer the questions I asked you as they are trying to work out WHY the LSD will be binding up in a straight line.
×
×
  • Create New...