Jump to content
SAU Community

Shockworks Presents Round 9 - Sandown Raceway 1st Oct | Grand Final Day


Recommended Posts

Hey guys I have fixed the track day requirements link for anyone not sure what is required for a car and driver to attend.

 

http://www.sau.com.au/forums/topic/453779-track-day-requirements/

  • Like 1

Cams Manual Schedule D - Apparel

http://docs.cams.com.au/Manual/GeneralRequirements/GQ05-Schedule-D-2016-1.pdf

We're "Race" / "Multi Club"... So Helmet level is "B"...

In the table it seems to list "E22 (with 03, 04 or 05 amendments)" which looks like your helmet. But don't quote me on that, that table is confusing as hell.

  • Like 1

Ha ha yeah thanks for that@Odium i found that table super confusing too ! Just strange you dont need a as/nzs sticker on a road approved helmet

3 hours ago, OYEAHA said:

Ha ha yeah thanks for that@Odium i found that table super confusing too ! Just strange you dont need a as/nzs sticker on a road approved helmet

 

Sorry was busy earlier could not reply in length.

 

the ECE is accepted by vic roads as well now so it's not just CAMS that are accepting it.

 

so Snell, ECE, AS and BS we accept.

 

 

  • Like 1

Thanks Martin :)

Yep in my search for the answer I came across an article saying that they were road legal in Victoria since mid 2015, but still illegal if you travel to certain other states on your motorbike (ridiculous considering that you can be considered "Safe" in a $75 helmet, but not in a $750 helmet)

Thanks for the clarification

Hello :-)
I just bought a fire extinguisher, its a 1kg cams approved, the date on the neck is 03 2016. The lovely man at the shop assured me that it was the make date i just want to confirm. Is it valid 3yrs from that date? Im having trouble getting my head around whats an expiry date/make date. Any help would be appreciated. Tegan

that is correct 3 years from the date stamped on the bottle.

 

so good till march 2019

 

make sure it is bolted in, no cable ties/tech screws and such.

 

M

19 minutes ago, fdrx7 said:

Hello :-)
I just bought a fire extinguisher, its a 1kg cams approved, the date on the neck is 03 2016. The lovely man at the shop assured me that it was the make date i just want to confirm. Is it valid 3yrs from that date? Im having trouble getting my head around whats an expiry date/make date. Any help would be appreciated. Tegan

Yes that is correct. 3 years from manufacture date

Unless it specifically says "Expiry Date" then consider it a Manufacture date, as different uses have different time spans (for the same equipment)... Stupid I know.

  • Like 2
On 9/26/2016 at 10:35 PM, acsplit said:

I was just about to post this, yep contact brendan during office hours garage $50 can fit two cars

Damn that's cheap, PI was like 4 times that




  • Latest Posts

    • ECUtalk pages don't mention they support the ABS computer (consult port has more than one CAN), so you might just need a different scan tool. But, I would expect ABS is a different light to the brake warning/handbrake light, do you see an ABS light come on for a few seconds when you turn the key from ACC to IGN? But since you said: I'd have a look at the ABS sensors in the rear hubs to make sure they are not damaged, disconnected etc.
    • OK, if it idles at 1000+ with the AAC, its not an idle airflow problem. The cold start valve just gives extra air when the engine is cold, but you have enough air without it to idle at 1000. I think you are back to a fuel problem, sorry. Can you see the fuel pressure staying constant or does it drop as the revs drop to a stall?  
    • Well, I was using ECUTalk software if that helps? Not sure if that only can see engine codes? Is there any other software I could give a try? Or any way I can get a blink code?
    • I never touched it, it should have. I'll try to give it an adjust. With IACV plugged in, it idles at around 1120RPM on average. Max 1200 RPM, Minimum 1025RPM before it starts dropping right before stalling. Took the data from the Nistune logs.
    • Thats what im trying to solve bro  no one with aem tuner experience would advice  much appreciate 
×
×
  • Create New...