Jump to content
SAU Community

Recommended Posts

So in February I had my car tuned making around 280rwkw. The car drove fine maybe a little carp down low, which I thought was the vct plug needing replacing.

The car then began flashing the cel/knock light. Replaced the vct plug and took it back to get the tune looked at. I've been told the car can't handle timing above 10psi and 4 degrees of timing was taken out anywhere above 10psi.

IAT were mid to high 50. Don't know if that's an issue.

Car has

Hypergear atr43ss2

Top feed rail with 1000cc xspurt

Jjr return flow cooler

Haltec platinum pro

Any reasons why a car would be fine with the timing then after a few months hate it.

Tuner thinks the 98 down here is bad but I can't see why it would be that bad/different

Link to comment
https://www.sau.com.au/forums/topic/467658-car-wont-take-timing-with-out-knock/
Share on other sites

How big is your exhaust? Possibly collapsed CAT? Can you check pressure or temps pre and after intercooler?

Just saw you have a Venom cat so probably not that.

Same tuner as February?

Stao might be able to weigh in here, but I believe he was having issues with JJR Belmouth dump pupes at one stage. The flange doesnt quite match up to the gasket/turbo and you need to grind out the dump a bit to make it match.

I never had this issue but I believe that it was a problem

Do you know how much timing is actually in the MAP up were the problem area is?

Ok I don't think I had the issue as I would have noticed when I went to put the gasket on.
No I don't know how much timing is in there before after the change. I may have to see if I can find out tomorrow.

If everything was working fine for a while then it changed without notice then my bet is fuel starvation, time to check the filter, FPR, pump etc

Pump is my guess, its not delivering enough when you boost!

He did mention he took a bit of fuel out of the map as the afr was a touch rich. Would that rule out the fuel system? I didn't ask either but a pressure gauge in the fuel line would tell whether there was an issue in the fuel system wouldn't it?

When it changes from something that used to work, then it is not the fundamental architecture of the car.  If it NEVER took timing then we'd go looking at the return flow cooler, the exhaust, etc etc.  So we look to things that can change.  As has been mentioned already, cat is a possibility.  After that it's fuel system, as has also been said.  What may be happening is something unexpected like just one dirty/part blocked injector.  If you get one cylinder running a bit lean it will knock and the others won't, and the mixtures may not show up too badly because 5/6 of the engine is working right.  Those Bosch injectors may or may not have the little inlet filters in them.  They can catch crap and bock really quick.

  • Like 1
13 hours ago, MatthewT85 said:

Any reasons why a car would be fine with the timing then after a few months hate it.

Tuner thinks the 98 down here is bad but I can't see why it would be that bad/different

 

The fact the tune hadn't gone leaner would suggest it's less likely to be a fuel delivery issue which is one of the causes for this kind of thing which I've seen.  To cause THAT much sensitivity at that low boost and requested timing would need to be quite the fuelling issue, not something that would be too subtle to pick up even if it was only one cylinder - imho.

The other thing (and probably more common cause for this type of stuff) is triggering issues causing the effective timing to fly way off requested timing.   Either make sure the wiring to the CAS is good, or if you can find someone with the same type of CAS then maybe try swapping them over - or anything else you have the tech to do to rule that out.

Edited by Lithium
2 hours ago, Lithium said:

To cause THAT much sensitivity at that low boost and requested timing would need to be quite the fuelling issue, 

 

sorry does that mean it would be pretty obvious if there was a problem with fuel system and its most likely not the issue?

On 11/13/2016 at 0:35 AM, hypergear said:

I'm leaning towards to what the Afr gauge say as well.

do you mean if the afr was fine or rich then there isnt an issue with fuel system(injectors, FPR ect)

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • That was the first session so not a lot to take from the day. It was low 20s ambient and the coolant had got to 110 (and obviously had some pressure!) so that still needs to be addressed. I haven't downloaded the data yet but will. I had refilled the auto trans with Redline DT6 because it claimed the best viscosity I could find at 100o. It wasn't really long enough to get a good feel for that; while the trans got to 100o in the session it still wasn't shifting crisply as I hoped. I think I'll try a few more sessions before judging. No steering motor overheat but I'd hope not in only 1 session! But finally the suspension; it was night and day over the standard stuff and the car was a couple of seconds quicker on the same crappy tyres, which is a huge difference. I'll stick with that and get some sway bars and a mechanical diff sorted too and see how that all goes together
    • I guess it’s partially a compromise of how my car is used, wanting to be able to switch from drift to grip with track side on-car adjustment. Also partially with the way the knuckles are set there is more static camber but less dynamic camber gain. 
    • OK, so update from the track day on Friday It was a classic "an unfortunate series of events'. There were a few cars around and when i checked my mirror coming out of the fish hook I notice some smoke from the rear of mine. Looked again and it was getting much worse, I figured I'd blown a turbo or something to got off it and pulled off the racing line. However.... since it is a left hairpin into a right kink, I was on the inside of the next corner. There was a car passing me on the left and a big drop off over the ripple strip on the right......and someone had knocked the witch's hat that was on the apex about 1m onto the track. So, between those 3, I decided to mow down the cone and not damage my car/the other car. Right choice, but surprising result.  The car decided the cone was a small pedestrian so it blew the rear bonnet hinges up to protect their head in the upcoming person to car impact....I didn't see that coming and like an airbag deployment it happened super fast. Straight into the pits from there, everything was driving fine but it became clear it was a coolant leak not smoke, it was billowing up onto the windscreen. Onto the trailer and home. I'll do a separate thread about the repair (once I work out what it is ), but the immediate problem was the bonnet wouldn't open because the front was pinched onto the front bar and would not release. Ultimately we unbolted the hinge from the bonnet, pulled it back a little and it released from the front OK. "There's your problem", the top radiator hose had popped off at the radiator.
    • Yeah that looks like great caster, but I'd suggest trying less front camber some time and seeing if it helps with braking without reducing mid corner speed too much
    • I ended up setting the rear 5mm higher than normal to give some clearance.  My plan is to run the least camber I can in the rear which I think with the extra width is going to need to be -1.75 to -2.00° just to get clearance.  Guards have been rolled and pulled as much as they can/I would be wanting to.  front has the Acostal knuckle with the KPI change and the drop etc. So should be okay with the existing settings I have run with AR1s etc Front: Toe total -2mm(1mm out each side) Caster +7.5° Camber -3.8° Ackerman +15°
×
×
  • Create New...