Jump to content
SAU Community

Recommended Posts

So in February I had my car tuned making around 280rwkw. The car drove fine maybe a little carp down low, which I thought was the vct plug needing replacing.

The car then began flashing the cel/knock light. Replaced the vct plug and took it back to get the tune looked at. I've been told the car can't handle timing above 10psi and 4 degrees of timing was taken out anywhere above 10psi.

IAT were mid to high 50. Don't know if that's an issue.

Car has

Hypergear atr43ss2

Top feed rail with 1000cc xspurt

Jjr return flow cooler

Haltec platinum pro

Any reasons why a car would be fine with the timing then after a few months hate it.

Tuner thinks the 98 down here is bad but I can't see why it would be that bad/different

Link to comment
https://www.sau.com.au/forums/topic/467658-car-wont-take-timing-with-out-knock/
Share on other sites

How big is your exhaust? Possibly collapsed CAT? Can you check pressure or temps pre and after intercooler?

Just saw you have a Venom cat so probably not that.

Same tuner as February?

Stao might be able to weigh in here, but I believe he was having issues with JJR Belmouth dump pupes at one stage. The flange doesnt quite match up to the gasket/turbo and you need to grind out the dump a bit to make it match.

I never had this issue but I believe that it was a problem

Do you know how much timing is actually in the MAP up were the problem area is?

Ok I don't think I had the issue as I would have noticed when I went to put the gasket on.
No I don't know how much timing is in there before after the change. I may have to see if I can find out tomorrow.

If everything was working fine for a while then it changed without notice then my bet is fuel starvation, time to check the filter, FPR, pump etc

Pump is my guess, its not delivering enough when you boost!

He did mention he took a bit of fuel out of the map as the afr was a touch rich. Would that rule out the fuel system? I didn't ask either but a pressure gauge in the fuel line would tell whether there was an issue in the fuel system wouldn't it?

When it changes from something that used to work, then it is not the fundamental architecture of the car.  If it NEVER took timing then we'd go looking at the return flow cooler, the exhaust, etc etc.  So we look to things that can change.  As has been mentioned already, cat is a possibility.  After that it's fuel system, as has also been said.  What may be happening is something unexpected like just one dirty/part blocked injector.  If you get one cylinder running a bit lean it will knock and the others won't, and the mixtures may not show up too badly because 5/6 of the engine is working right.  Those Bosch injectors may or may not have the little inlet filters in them.  They can catch crap and bock really quick.

  • Like 1
13 hours ago, MatthewT85 said:

Any reasons why a car would be fine with the timing then after a few months hate it.

Tuner thinks the 98 down here is bad but I can't see why it would be that bad/different

 

The fact the tune hadn't gone leaner would suggest it's less likely to be a fuel delivery issue which is one of the causes for this kind of thing which I've seen.  To cause THAT much sensitivity at that low boost and requested timing would need to be quite the fuelling issue, not something that would be too subtle to pick up even if it was only one cylinder - imho.

The other thing (and probably more common cause for this type of stuff) is triggering issues causing the effective timing to fly way off requested timing.   Either make sure the wiring to the CAS is good, or if you can find someone with the same type of CAS then maybe try swapping them over - or anything else you have the tech to do to rule that out.

Edited by Lithium
2 hours ago, Lithium said:

To cause THAT much sensitivity at that low boost and requested timing would need to be quite the fuelling issue, 

 

sorry does that mean it would be pretty obvious if there was a problem with fuel system and its most likely not the issue?

On 11/13/2016 at 0:35 AM, hypergear said:

I'm leaning towards to what the Afr gauge say as well.

do you mean if the afr was fine or rich then there isnt an issue with fuel system(injectors, FPR ect)

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • Ok thanks..that was my second question if i can somehow bypass this even with Nistune(that is all i have right now...aparat from stock ECU. So with some aftemarket it can by "bypassed" or make it work?  I know there is Link or Haltech (mainly used). We have ECUmaster here so i will gather some info about it.
    • Yes. You will need to get the original boost sensor and wire it in. That is.... if you plan to use a stock ECU - even a Nistuned ECU. The Nissan ECU will not operate correctly without it connected. And yes, it will do annoying stuff like you are experiencing. You will almost certainly be better off with some aftermarket ECU, than trying to hunt down rare sensors.
    • Ok so ABS/TCS is "not" the problem. Yeah i know now about the ABS with Nistune(i told that to the Nistune guy) but iam not 100% why or why i dont have ABS. ABS cube is in the engine (always has been) but i had braked couple of times rly hard and brakes just locked and scream. Does all Skylines have ABS cube? That boost sensor https://www.sau.com.au/forums/topic/367633-wtb-r34-gtt-turbo-pressure-sensor-pics-inside/ Is this it? I need to ask but i have a picture of engine bay and i do not see that (100% is not in that place) If i do not have this the car can do what mine is?(cutting around 4000 rpm) Here is the pic of my engine bay(only one i have) BUT i think i dont have that cuz loom was used from my RB20DE NEO and i know (obviously) that it does not have boost control or any wire to that...) so maybe that is the problem? (i dont know for 100% if that car where the engine is from had that)...but i dont have the loom from that
    • I'm with you here. It's either loom has an issue, OR, injectors are not functioning properly. It could even be they're just constantly dribbling, hence the wet, but not firing.
    • Depending on how long the car sat it is very possible for injectors to be stuck open or closed, I'd get them cleaned and flow tested. Other than that, obviously when the loom changes and the car doesn't start any more....the loom is suspect so some tracing / comparing may be required
×
×
  • Create New...