Jump to content
SAU Community

Rb30 25 neo cometic head gasket problem

lcxu105

By lcxu105,
in Engines & Forced Induction

 Share

Recommended Posts

lcxu105 Proficient

lcxu105

Posted
Posted
Rb30 25 neo cometic head gasket problem

Ok everyone. 

Problem is a brand new engine 30 25 neo so all surfaces are machined flat fitted cometic rb30 head gasket and have a oil leak between the head and block rear passenger side. 

The gasket can only fit one way so thats not the problem.

Engine has 1mm oil restrictors fitted and vct mod. 

Just pulled the covers off and checked the torque settings at 110nm i know that it's 108.49nm for arp studs.

Just bumped it up to 118nm figured it couldn't hurt much.

Can anyone give me any insight as to why it might leak.

Thanks in advance.

 

Weaselman Collaborator

Weaselman

Posted
Posted

Usually on the first steps of tightening the head you need to back the studs off and re do them. When using cometic gaskets I don't back them off because you've flattered the metal plates already and unloading them can cause them to leak. Now I'm not a qualified mechanic but it's how I do it and I've never had them leak.

89CAL Grand Master

89CAL

Posted
Posted

So are you saying you have loosened it all off and re-torqued it?

If it's already leaked and you've taken all the pressure off the gasket and torqued it back down, I would be putting the order in for a new head gasket now. Once oil gets inbetween the surfaces, its not likely to seal properly, And I agree with above, after the first time the gasket is crushed, I wouldn't use it again.

rx-line Enthusiast

rx-line

Posted
Posted (edited)

Threads need to be lubbed in order to keep the steel alloy of the stud from galling the aluminum, this will give an accurate torque, rather than a false torque if galling has occurred. A false torque could cause a leak for sure.

Also you might want to try torquing from the inside working your way from side to side to the outside of the head, we have had good luck with this.

As for a reason things change a fair bit when you clamp a head to a block, it's surprising how things move. If the above fails I would look at the head and block to see how well they have been surfaced.

Here's a thought as well, you might be experiencing above average crank case pressures due to you rings not being seated in with the new build. Make sure not to use synthetic oil when breaking it in, it delays the process by a lot. This may be exaggerating the leak.

Hopefully this may help you.

Edited by rx-line
lcxu105 Proficient

lcxu105

Posted
  • Author
Posted (edited)

Lube was used on threads to tension block was decked square  to tunnel and head was machined with reco and port work  i use hpr5 penrite. engine was run in on a dyno. 

I do think i have over filled the oil tho too.

 

Edited by lcxu105
KiwiRS4T Grand Master

KiwiRS4T

Posted
Posted
1 hour ago, lcxu105 said:

 i use hpr5 penrite. engine was run in on a dyno. 

Including initial fill? As RX-Line said mineral oil is better for running in - but probably too late to change now. Did you use Hylomar or similar to stick the gasket down? How much oil actually leaked? I wouldn't have expected overfiling to result in a leak from there.

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now
 Share
Go to topic listing


  • Similar Content

  • Latest Posts

    • MBS206
      Duncan's V37.......race car?

      By MBS206 · Posted

      Even more fun, leave all the ADAS stuff plugged in, but in different locations, hopefully avoid any codes!   And honestly, all these new cars with their weird electronics. Pull all the electronics out Duncan, and just shove an aftermarket ECU and if needed a trans controller in, along with a PDM. Make it run basic but race car styled!
    • Duncan
      Duncan's V37.......race car?

      By Duncan · Posted

      To follow up a question from earlier too since I had the front bar off again (fking!) This is what is between the bumper and the drivers side wheel And this is the navigator side, only one thing but its a biggy! So basically....no putting coolers in the wheel arches without a lot of moving other stuff. Assuming I move to properly race prepping this car I'll take that job on and see how the computers respond to removing a whole bunch of ADAS modules
    • Duncan
      Duncan's V37.......race car?

      By Duncan · Posted

      So I prepped the car for another track day on Wednesday (will be interesting to see coolant temps post flushing out and the larger reservoir, with a forecast of 3-14 being 20o cooler than last time I took it out). Couple of things to mention; since I am just driving the car and not taking a support vehicle, I took the rear seats out and just loaded the back up Team Trackday style. Look at all that space! To cover off removing the rear seat....it is weird (note the hybrid is probably different because it wouldn't have folding rear seats) Basically, you remove the lower seat base, very similar to a r series but it is a clip that pulls forward to release the base rather than it being bolted down. Easy Then, you need to remove the side section of the rear seat on each side. There is a 14mm head nut at the bottom of the side piece, the it slides upwards off a hook at the top to release; you also need to unhook the seatbelt from the loop at the top. Then the centre piece is weird. You need to release/fold the seats forward with the tab in the boot on each side From there, there are 2,x12mm headed bolts holding the rear of each seat to the folding bracket, under the trim between the rear seat and the boot (4x christmas tree clips there, they suck). The seat is out but you can see where the bolts attach to the bracket
    • RP1421
      S15 Spec R

      By RP1421 · Posted

      As discussed in the previous post, the bushes in the 110 needed replacing. I took this opportunity to replace the castor bushes, the front lower control arm, lower the car and get the alignment dialled in with new tyres. I took it down to Alignment Motorsports on the GC to get this work done and also get more out of the Shockworks as I felt like I wasn't getting the full use out of them.  To cut a very long story short, it ended up being the case the passenger side castor arm wouldn't accept the brand new bush as the sleeve had worn badly enough to the point you could push the new bush in by hand and completely through. Trying a pair of TRD bushes didn't fix the issue either (I had originally gone with Hardrace bushes). We needed to urgently source another castor arm, and thankfully this was sourced and the guys at the shop worked on my car until 7pm on a Saturday to get everything done. The car rides a lot nicer now with the suspension dialled in properly. Lowered the car a little as well to suit the lower profile front tyres, and just bring the car down generally. Eternally thankful for the guys down at the shop to get the car sorted, we both pulled big favours from our contacts to get it done on the Saturday.  Also plugged in the new Stedi foglights into the S15, and even from a quick test in the garage I'm keen to see how they look out on the road. I had some concerns about the length of the LED body and whether it'd fit in the foglight housing but it's fine.  I've got a small window coming up next month where I'll likely get a little paint work done on the 110 to remove the rear wing, add a boot wing and roof wing, get the side skirt fixed up and colour match the little panel on the tail lights so that I can install some badges that I've kept in storage. I'm also tempted to put in a new pair of headlights on the 110.  Until then, here's some more pictures from Easter this year. 
    • joshuaho96
      R32 GTS (RB20DE) Injectors Replacement

      By joshuaho96 · Posted

      I would put a fuel pressure gauge between the filter and the fuel rail, see if it's maintaining good fuel pressure at idle going up to the point when it stalls. Do you see any strange behavior in commanded fuel leading up to the point when it stalls? You might have to start going through the service manual and doing a long list of sensor tests if it's not the fuel system for whatever reason.
×
×
  • Create New...