Jump to content
SAU Community

Recommended Posts

37 minutes ago, Dose Pipe Sutututu said:

That's how the NBN is being rolled out lol

lol no, the NBN is being rolled out equivalent to you just saying f**k it and using the cracked o-rings

 

48 minutes ago, Dose Pipe Sutututu said:

So close yet so far, typical NBNish delivery lol.. Over budget and project schedule blown out of the water.

This is EVERY Government funded project

  • Like 1
  • Haha 2
1 hour ago, iruvyouskyrine said:

Those bolts go at the very back of the head on either side. Do you even RB bro?

No :(

I SR20 more lol...

where exactly????

1 hour ago, Dose Pipe Sutututu said:

are those the cylinder head to block bolts that go on the outside??

That's what I thought they were when I saw the pic. I thought there was one front and one rear though not both at the same end?

1 hour ago, Dose Pipe Sutututu said:

are those the cylinder head to block bolts that go on the outside??

Yes correct. 2x M6 bolts

 

38 minutes ago, timmy_89 said:

That's what I thought they were when I saw the pic. I thought there was one front and one rear though not both at the same end?

1 at front intake side and 2 at rear either side.

I should note that i never put them back in any of my engines. With RB25's you can't access the front bolt without taking the inlet manifold off which is a shit job which annoys me as i would rather take the inlet manifold off when the head is out of the car.

15 minutes ago, iruvyouskyrine said:

I should note that i never put them back in any of my engines. With RB25's you can't access the front bolt without taking the inlet manifold off which is a shit job which annoys me as i would rather take the inlet manifold off when the head is out of the car.

Yea they didn't go back on my engine either lol

ahhh I installed coppery colours ones back into those holes.. interesting those bolts I took a photo of, I wouldn't' think they would fit as they're wider than the golden/copper ones I used from the R33 motor.

mad, no fear - didn't fk up

Update but no photos (taking inspiration from @luke gtr lol).

Removed R33 plenum, installed bottom half of R34 plenum.

Now awaiting 1550cc Bosch injectors and a Plazmaman rail. The initial plan was to use the 875cc Siemen DEKA V I had from my old motor but anticipating the power this motor will make there's no way those injectors would cut it, even if I ran 4 bar base pressure.

Been trying to order parts again from Andrew @kudos.motorsports but he isn't replying to my emails :(

 

Update but no photos (taking inspiration from [mention=37584]luke gtr[/mention] lol).
Removed R33 plenum, installed bottom half of R34 plenum.
Now awaiting 1550cc Bosch injectors and a Plazmaman rail. The initial plan was to use the 875cc Siemen DEKA V I had from my old motor but anticipating the power this motor will make there's no way those injectors would cut it, even if I ran 4 bar base pressure.
Been trying to order parts again from Andrew [mention=1172]kudos.motorsports[/mention] but he isn't replying to my emails [emoji20]
 
Nawww, thanks brosef.
1 hour ago, ActionDan said:

Side feed in that boat anchor engine aren't they? 

yeah nah cuz.. I had top feeds in there under the stock plenum before they were even mainstream :)

http://www.trak-life.com/diy-converting-top-feed-injectors-r33-gts-t-skyline-rb25det/

Yah... stainless internals, not modified by any laser cutter/mill/bench grinder/side cutters

US guys usually refer to them as Siemens DEKA V 80lb

I hate modified injectors, those "Bosch 1250cc" are milled.

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now



  • Latest Posts

    • Yep, the closest base tune available was for the GTT, I went with that and made all the logical changes I could find to convert it to Naturally Aspirated. It will rev fine in Neutral to redline but it will be cutting nearly 50% fuel the whole way.  If I let it tune the fuel map to start with that much less fuel it wont run right and has a hard time applying corrections.  These 50% cuts are with a fuel map already about half of what the GTT tune had.  I was having a whole lot of bogging when applying any throttle but seem to have fixed that for no load situations with very aggressive transient throttle settings. I made the corrections to my injectors with data I found for them online, FBCJC100 flowing 306cc.  I'll have to look to see if I can find the Cam section. I have the Bosch 4.9 from Haltech. My manifold pressure when watching it live is always in -5.9 psi/inHg
    • Hi My Tokico BM50 Brake master cylinder has a leak from the hole between the two outlets (M10x1) for brake pipes, I have attached a photo. Can anyone tell me what that hole is and what has failed to allow brake fluid to escape from it, I have looked on line and asked questions on UK forums but can not find the answer, if anyone can enlighten me I would be most grateful.
    • It will be a software setting. I don't believe many on here ever used AEM. And they're now a discontinued product,that's really hard to find any easy answers on. If it were Link or Haltech, someone would be able to just send you a ECU file though.
    • Yes sir am asking is there possible way from aem tuner from wiring pins 
    • Have you checked cam to crank timing and confirmed balancer marks are correct?
×
×
  • Create New...