Jump to content
SAU Community

Recommended Posts

5 hours ago, vxsr33 said:

The rs3s also dont make a lot of road noise which is good.

Hardsteppa, i will check out the RSRR next time i need a new set of tyres. Thanks

I'd go a ride in a car with RSR/RSRR before deciding, from all I've read they're cheap and stick well but very noisy. Some have compared the noise to the KU36, which I run, and that's certainly a noisy tyre.

RS3's are meant to have a good balance between price/grip/wear/noise.

i run RSR on the GTR and would never complain about road noise... They have a slight hum but you don't really notice it after a while. And that is even with a relatively quiet exhaust. 

  • 1 month later...

it is indeed.

had Rs3's for a few months and yeah they're not bad, but...ad08r's now on all four wheels and wow..I can honestly say, never experienced anything like it. Best tyre I've ever used.

I've had ad08r on my car for a while now. Done a few track days on them and driven daily, they still have 85% + tread and grip the same as when new. Compared to cheap motorsport Street tyres, rsr, 123s etc. These actually last and it will be a long time before you see their performance drop off. Easily the best road tyre I have used that can handle and work well on the track (never used rs3 to compare though). I've recently been using A050 semis for my last 2 track days and have only managed to go 1 second quicker. If I don't end up going at least another sec quicker, I'll be going back to ad08r.

  • Like 1
3 hours ago, -S- said:

Can anyone comment on re71r ? Will these tyres be a waste if used for street only? I think these are on par with the ad08r ?

The new re71r's are amazing.  I was strongly debating mounting a set but a great deal came up that I couldn't pass on.  They are hugely popular in auto cross in the states.  If you drive spiritedly, you would enjoy the extra grip but I doubt you would get anywhere close to their limit on the street.  I haven't even hit the limit on my 003's.  In the end, they're one of the best street tires you're going to find, but to determine if they are worth it to you would be dependent on your driving style.

I initially wanted re003 as i think the re003 would last longer than the re71r... plus maybe the re003 would be better on the wet too compared to the re71r... then again i think the tread wear rating for both are 200 and 210 respectively so not much difference. (I could be wrong) but thanks for the feedback! Might really look into it. ..

 

2 hours ago, -S- said:

I initially wanted re003 as i think the re003 would last longer than the re71r... plus maybe the re003 would be better on the wet too compared to the re71r... then again i think the tread wear rating for both are 200 and 210 respectively so not much difference. (I could be wrong) but thanks for the feedback! Might really look into it. ..

If the RE71R is a rave-worthy tyre, then the RE003 is a long way from that.  I put them on my car.  Previously having used AD08Rs and before that various KU36s etc.  The RE003 has nowhere near as much dry grip as the AD08R, so should be at least as far behind the RE71R.  The RE003 is pretty good in the wet, no argument.  The life expectancy looks to be pretty reasonable.  I'm going to get a lot more life out of them than the AD08Rs, which is the main reason I decided to try them.

FWIW, I'd probably use the RE003 again, even with lower grip levels.  They're still a pretty good tyre.

ok i'm revising my vote. AD08's are great, and hopefully they should last a while, but, RSRR's are the best (grippiest dry, and I also found them fine in the wet)  tyre I've used. Don't last long, but, don't cost that much either.

  • Like 1

Don't slap me around here but I'm running NS2R's by Nankang.

Semi Slicks very good in the dry and in the wet I had traction in 1st my old Bridgestone R002's didn't.

Not saying the best tyre but pretty good so far.

Have 1000km on them but that's first review.

 

 

 

 

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now



  • Similar Content

  • Latest Posts

    • Hi...so a "development" here aswell The swap is "done" and car went "test drive" BUT it seems the clutch(maybe gearbox?) is a little bit sad? I bought this clutch kit https://justjap.com/products/xtreme-heavy-duty-organic-clutch-flywheel-kit-nissan-skyline-r31-r32-r33-push-type "Problem" is that the first gear is hard to put into and it seems that the clutch is not disengaged. It was not the problem with the old clutch...(or like sometime the first gear would not get as easy specialy when the fluid was cold) So? Can it be like...bad "install" or is the clutch wrong ((it should not have been) i done research to get the right one) Or is this "normal" with new clutch and needs to be break in? 
    • @Duncan I can try  and thanks i did not thought about VIN and part numbers for 33/34. @GTSBoy yeah it looks like iam gonna do that  
    • Forgot to include this but this is the mid section of my steering rack that looks like it has a thread/can be turned with that notch mentioned in the post:
    • Hey everyone, Wanted to pick some brains about this issue I'm having with rebuilding my 33 rack (PN is 49001-19U05). All of the tutorials/videos I've seen online are either R34 or S Chassis racks which seem to be pretty straightforward to disassemble but this process doesnt carry over to my rack. Few of the key differences that I've noted The pinion shaft on the other racks bolt on with 3 torx bolts: Whereas my rack bolts on with 2 allen head bolts: These changes are pretty inconsequential but the main difference is how you pull the actual rack out of the housing. The other skyline/s chassis racks can be taken out by tapping the rack out of the body with a socket and it just slides right out. I'm unable to do that with my rack because there's a hard stop at the end that doesn't let the seal/shaft be tapped out. Can also see a difference in the other end of the rack where mine has a notch that looks like you're able to use a big wrench to unthread 2 halves of the rack whereas the other racks are just kinda set in with a punch. My rack: Other racks: TLDR; Wanted to know if anyone has rebuilt this specific model of steering rack for the R33 and if there were any steps to getting it done easier or if I should just give this to a professional to get done. Sorry if this post is a bit messy, first one I've done.
    • I would just put EBC back on the "I would not use their stuff" pile and move on.
×
×
  • Create New...