Jump to content
SAU Community

anyone heard of these shocks?

darksould43
 Share

Recommended Posts

darksould43 Contributor

darksould43

Posted
Posted

i was awondering why the stance on my car didnt look right, and it looks like it sits almost an inch higher at the front so i took the wheel off and these are the shocks that are on there, anyone heard of them? 

also i do plan on swapping out all of the suspension, i would go for bc gold coilovers but in nz you have to get a cert, so another 500 or for that, but i found a set of nismo s-tune shocks and springs for a few hundred less that coilovers, has anyone had any experience with them?

35476773_2072567096292017_289781013964390400_n.jpg

35552048_2072567089625351_3737977417155739648_n.jpg

Link to comment
https://www.sau.com.au/forums/topic/474296-anyone-heard-of-these-shocks/
Share on other sites
Jordy32 Experienced

Jordy32

Posted
Posted

Nismo S-Tune were in my 34, fine for the street/spirited drive and are fairly comfortable.

Just keep in mind that they are probably quite an old unit by now and it'd be much better to get something brand new. The last thing you want to do is install old nismo shocks and have one die on you.

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now
 Share
Go to topic listing


  • Similar Content

  • Latest Posts

    • nash47
      Cas issue

      By nash47 · Posted

      Hello , im new here and i have A31 home build  RB25det neo stock eng / turbo  aem ems 2 blue connector  aem 3.5 map aem cas disk aem wideband connected to ecu  355 lph pump 550 nismo yellow injectors side feed aftermarket regulator  and won’t start with base aem tuner basic tune eventually flipped cas 180 degree so it triggers on correct stroke not in exhaust cycle  Now it won’t start Wideband reads 10 and 11 at lowest fuel setting  and will share calibrations soon for aem tuner i think something is wrong in aem tuner    please if you have any information, am very grateful         
    • nxh
      R34 4 door side skirt identification

      By nxh · Posted

      Legend. I ended up finding the facebook account of the owner of the first car i sent but sadly he deactivated the account. I think you’re right in saying it’s some sort of well done custom job. Really appreciate your help anyways.
    • GTSBoy
      boost source Size Garrett gt28 gen2

      By GTSBoy · Posted

      Totally equivalent. Stock often goes from the comp cover because that's where the actuator is also installed and the factory needs 2" of hose to make the connection - and it comes as a pre-assembled unit. They totally have a boost reference from somewhere between the turbo and the throttle(s). Oh, jeez. Just do it in M12 then. We don't actually care that much. I would expect any such AN converter fitting to rely on an o-ring or some other seal onto a flat surface under the flange of the hex**, because bolt threads are no intended to provide a pressure seal. unlike..... pipe threads. **which also requires a suitably flat and smooth surface on the turbo's boss to provide the seal.
    • timmy94
      boost source Size Garrett gt28 gen2

      By timmy94 · Posted

      I also used NP   That’s were it’s seems to be the best place to fit it? All schematic shows also that it’s should be referenced from the turbo housing. But idk, I do see high hp cars without any connection or anything to their turbos, so I really don’t know how they connect their things
    • timmy94
      boost source Size Garrett gt28 gen2

      By timmy94 · Posted

      I do have loctite 243 and 246 and a few more models. I could drill it now in place and make new threads for m12 and order an4 - m12 coupling and fit that to the turbo. Run a braided hose to the EBC which I could get a an4 to 1/8npt 
×
×
  • Create New...