Jump to content
SAU Community

Recommended Posts

Hae all so im replacing my wheel bearing on my 1993 r32 and its been a complete nightmare. So i originally bought a bearing off ebay for a r32 as pictured451394808_Screenshot_20180611-174953_SamsungInternet.thumb.jpg.ee0f9ae64a3cbda25b225d1ae02e52bd.jpg

Then once apart i come to realise its wrong and its this type20180611_173717.thumb.jpg.1028eb28a7d1684f5009aa3c71c4a3a9.jpg

Now after alot of searching i come to the assumption i have a type m? Because i have 4pot brakes on front 2pot on the rear and digital climate control. i eventually found a bearing through bursons it came up as a r32 gtr drum handbrake type so i got it, fitted it up and the inner diameter for the cv spline is to big. Can some one please tell me exactly which one will fit because the lady at bursons said there were no other listings for a 32 apart from what i bought from them and the original one i bought. Need one by the weekend. Thanks 

Link to comment
https://www.sau.com.au/forums/topic/474302-need-help-with-r32-bearing/
Share on other sites

Assuming your car is 2wd (since you don't say, and neither does your profile) not 4wd?

When you say you "fitted it up and the inner diameter for the cv spline is to big" do you mean you can't press the hub face back into the bearing because it is too large, or because it is too small/loose or something else?

If you post up your VIN# someone can look up the exact nissan part# in FAST for you.

9 hours ago, Duncan said:

Assuming your car is 2wd (since you don't say, and neither does your profile) not 4wd?

When you say you "fitted it up and the inner diameter for the cv spline is to big" do you mean you can't press the hub face back into the bearing because it is too large, or because it is too small/loose or something else?

If you post up your VIN# someone can look up the exact nissan part# in FAST for you.

Sorry it is a 2wd and it came as a hub and bearing assembly. So when i went to push in the cv shaft it just spins without meshing to the splines

1 minute ago, Duncan said:

Ok...so you are correct, it is a type M.

Sik_R31 was the winner, part numbers you need are:

43280-30P05 / 43280-AA000, and

43281-30P05 / 43281-AA000

 

Excuse my ignorance but whats Sik_r31? 

Those part numbers will i be able to use to them at a place like bursons? 

sorry, Sick_R31, not Sik_R31

On ‎6‎/‎18‎/‎2018 at 10:24 PM, Sick_R31 said:

Bursons may not be able to use those numbers, they are a Nissan part number so they would need a cross check. You could buy from Nissan or Kudos as per Sick_R31's link. Or Amayama.com if you are not in a rush.

1 hour ago, Duncan said:

sorry, Sick_R31, not Sik_R31

Bursons may not be able to use those numbers, they are a Nissan part number so they would need a cross check. You could buy from Nissan or Kudos as per Sick_R31's link. Or Amayama.com if you are not in a rush.

Alright sweet as thanks heaps ?

  • 3 months later...

Bumping this thread, trying to get out the hub out from the knuckle after removing the entire assembly from the car...

I clamped the knuckle to a piece of wood, stood on it and went at it with my sliding hammer as hard as I could. Nothing besides me and the entire knuckle/wood thingy moved a single mm.

Just want to verify, the snap-rings are only there to hold the bearing, right?

Any options besides more heat, more lube and more force?

asda.png

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • I mean it's a bit late to say "This won't have any tangible effect and it is not worth spending more than about three seconds on it, please just enjoy the car" But I said it anyway. Does the pod actually get any airflow in that position behind a bumper like that?
    • Hey guys - apologies for digging this up. Has this website been shutdown or is the outage temporary?
    • So, went shopping at Just Jap for things that might work for the intake  After some trial fitting there I ended up with a 3" x 45° silicone bend, a 3" x 300mm alloy straight, and a humped joiner, some minor trimming will be required to shorten some of the stuff, but nothing that is beyond my "ham fisted" skills The guy at Just Jap was most helpful as we had all sorts of joiners,  bends and stuff out trial fitting  Laying it out above the stuff in there it seems everything will fit nicely, and looking at it, it is probably the way I should have been looking at doing it from the beginning, probably..... In the end it is a front bar off job anyway to remove the original stuff behind the front bar that is taking up the required realestate needed, so maybe a Thursday or Friday job And because I'm a hopeless consumer, I grabbed some new steel wheel nuts, the current ones are a spline drive type with a "security" socket, that somehow someone keeps misplacing, the new ones are a basic black steel 17mm hex socket In other news: I just did my "final" tax return, I am now officially a old retired veteran pensioner, and I'm milking the system for all it's worth,  life is good
    • I hadn't thought about the variable power steering assist. Presumably, it will always be the same level of assist as you get in an S14. The R32/3/4 are either helliishly heavy (at low speeds) if the solenoid is not powered at all, or hellishly too light (at high speed) if it is powered all the time. I presume that it is PWM controlled on those cars. I hadn't thought about the S cars not having variable assist. ugh. What crappy plebby cars they must be!  
    • Hmm yeah that is a good point. It looks like it'll just bolt in with no real issue besides maybe the bushings being different. My other concern was that 2 pin plug that I assume is used in some way to control the rack solenoid depending on the speed signal from the ecu. The DMAX rack doesn't even have that plug though so, don't think it'll matter. Might just order the rack and see how it goes. Will update this when I figure something out
×
×
  • Create New...