Jump to content
SAU Community

Recommended Posts

Helll all,

 

I am looking to put a better fuel pump in car and well nothing seems to be clear about it. I've asked a few suppliera and they stated the pump has a regulator attached so they do not make one. I have seen a few people use a basic walboro or aem pump without issue but I can not find anything specific. The gtst has the standard drop assembly while the GTR has the lower basket the pump sits in... 

I've searched here and can't find specific posts for it.. ant and all help is appreciated

Link to comment
https://www.sau.com.au/forums/topic/475259-r32-gtr-fuel-pump-upgrade/
Share on other sites

Don't know about gtst but yes gtr has a cradle.

Best to do it with the fuel very empty. Trust me!

Takes a bit of stuffing around to pull the cradle out, patience is required.

After it is out, install new pump same way as old pump. Best to use factory sock imo.

There's plenty of pumps out there however walbro has a new 525/h pump.

More importantly than the pump install is doing a rewire. Simple mod. Search that too lol

 

I have already pulled it out thinking it was bad, and I will be doing a direct relayed power to the new one but I can't actually find a replacement pump that is labeled for thr GTR. I can find expensive nismo or hks pumps but beyond that it's something to do with the pressure regulator on the pump.

Given that they look like EVERY OTHER FUEL PUMP......

https://www.google.com.au/search?hl=en&tbm=isch&source=hp&biw=1596&bih=863&ei=8e3UW9nYBobMvwS_0q_gBw&q=r32+gtr+fuel+pump&oq=r32+gtr+fuel+pump&gs_l=img.3..0l2j0i30k1j0i8i30k1j0i24k1l6.1949.5068.0.5355.17.16.0.0.0.0.348.2420.0j9j1j2.12.0....0...1ac.1.64.img..5.12.2418....0.OzbsQNiXZAI

 

Yep, get this one:

High Flow Walbro 255LPH Fuel Pump High Flow Skyline R33 GTR RB26DETT https://rover.ebay.com/rover/0/0/0?mpre=https%3A%2F%2Fwww.ebay.com.au%2Fulk%2Fitm%2F222562585010

Don’t know about the newer model so cannot recommend it but others seem to think it’s very good.

Edited by Robocop2310
  • Thanks 1

Buy a brand new pump not a used one out of a GTR. Many pumps will do but the Walbros will do the job. If you want to just do it once put the bigger one in so you don't have to change it to get to your new power target in the future.

4 hours ago, WantGTR said:

Don't worry about it. Even piss off that relief valve.

Walbro 525.

You seen how much power they draw? They WILL melt the stock wiring into the tank. And for no benefit for what the suse seems to want/need.

Thanks for all the input. I have planned to run a separate power feed off a relay to run whatever pump would work. I've always done that before to avoid melting or burning up stock wiring.

I'm just so confused as to what the pressure relief valve is designed to do. Maybe keep the pressure from being higher than needed?

 

 

It's the stock wiring AT THE PUMP that is the most concern here.  Not the wiring that trails off into the car.  Put a massive pump into the tank and feed it with the original dental floss wiring through the pump hat?  Recipe for voltage drop and wire meltage.  Put a pump in there that is bigger than stock (and, of course, big enough to do the job) but not too big for the wiring?  Yup, recipe for happiness.

If you go massive, you need to do more work.

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • Cheers. Skyline is back on the menu, can’t get rid of it. It’s like a child you don’t want, or herpes 
    • I got back to Japan in January and was keen to get back on track as quickly as possible. Europe is god-awful for track accessibility (by comparison), so I picked up a first-gen GT86 in December just to have something I could jump into right away. The Skyline came over in a container this time and landed in early January. It was a bit battered after Europe, though—I refused to do anything beyond essential upkeep while it was over there. The clutch master cylinder gave out, and so did the power steering. I didn’t even bother changing the oil; it was the same stuff that went in just before I left Japan the first time. Naughty. Power steering parts would’ve cost double with shipping and taxes, so knowing I’d be heading back to Japan, I just postponed it and powered through the arm workout. It took a solid three months to get the car back on the road. Registration was a nightmare this time around. There were a bunch of BS fees to navigate, and sourcing parts was a headache. I needed stock seats for shaken, mistakenly blew 34k JPY on some ENR34 seats—which, of course, didn’t fit—then ended up having the car’s technical sheet amended to register it as a two-seater with the Brides. Then there’s the GT86. Amazing car. Does everything I want it to do. Parts are cheap, easy to find, and I don’t care what anyone says—it’s super rewarding to drive. I’ve done a few basic mods: diff ratio, coilovers, discs, pads, seat, etc. It already had a new exhaust manifold and the 180kph limiter removed, so I assume it’s running some kind of map. I’ve just been thrashing it at the track non-stop—mostly Fuji Speedway now, since I need something with higher speed after all that autobahn time. The wheels on the R34 always pissed me off—too big, and it was a nightmare getting tires to fit properly under the arches. So I threw in the towel and bought something that fits better. Looks way cleaner too (at least to me)—less hotboy, less attention-seeking. Still an R34, though. Now for future plans. There are a few things still outstanding with the car. First up, the rear subframe needs an overhaul—that’s priority one. Next, I need to figure out an engine rebuild plan. No timeline yet, but I want to keep it economical—not cutting corners, just not throwing tens of thousands at a mechanic I can barely communicate with. And finally, paint. Plus a bit of tidying up here and there.  
    • Nope, needed to clearance under the bar a little with a heat gun, a 1/2" extension as the "clearancer", and big hammer, I was aware of this from the onset, they fit a 2.0 with this intake no problems, but, the 2.5 is around 15mm taller than a 2.0, so "clearancing" was required  It "just" touched when test fitting, now, I have about 10mm of clearance  You cannot see where it was done, and so far, there's no contact when giving it the beans Happy days
    • It's been a while since I've updated this thread. The last year (and some) has been very hectic. In the second-half of 2024 I took the R34 on a trip through Germany, Italy, France and Switzerland - it was f*cking great. I got a little annoyed with the attention the car was getting around Europe and really didn't drive it that much. I could barely work on the car since I was living in an inner-city apartment (with underground parking). During the trip, the car lost power steering in France - split hose - and I ended up driving around 4,000kms with no power steering.  There were a few Nurburgring trips here and there, but in total the R34 amassed just shy of 7,000kms on European roads. Long story short, I broke up with the reason I was transferred to Europe for and requested to be moved back to Japan. The E90, loved it. It was a sunk cost of around EUR 10,000 and I sold it to a friend for EUR 1,500 just to get rid of it quickly. Trust me, moving countries f*cking sucks and I could not be bothered to be as methodical as I was the first time around.
×
×
  • Create New...