Jump to content
SAU Community

Recommended Posts

Hey folks

I'm wrecking an r32 gtst manual sedan. Approximately 155000kms. The car has had a front end end and the passenger side has some damage (bonnet, fender, reo, rad support bar etc). The rest of the car is fine although the interior is a bit tired. The car wasn't mine previously, I bought it damaged when I had some ambitious plans but I don't have the time so I'm going to part it out.

The car has the usual bolt-on mods - coilovers, FMIC, turbo-back exhaust, bigger turbo, walbro fuel pump, pod etc

Everything is for sale except the wheels at this stage as I might keep them.

Happy to send specific photos and prices.

Happy to ship Aus-wide.

The following parts have been sold:

Steering wheel

Driver side window regulator

Fuel pump cradle

A pillar trims

Shifter boot and surrounding trim

Cheers

IMG_6841.JPG

IMG_6895.JPG

IMG_6893.JPG

IMG_6881.JPG

IMG_6876.JPG

IMG_6826.JPG

IMG_6828.JPG

IMG_6829.JPG

IMG_6823.JPG

Link to comment
https://www.sau.com.au/forums/topic/475975-wrecking-r32-gtst/
Share on other sites

59 minutes ago, jmknights93 said:

I literally asked him the same question haha.

And you were in before me.... damn it!!! lol

7 hours ago, R32GOJIRA said:

What is the dash cluster surround like? Are all the switch mounting tabs in good condition?

It has a couple of hairline cracks at the top but otherwise in good condition

4 hours ago, Adz2332 said:

how much on the coils? assuming 2 door and 4 door are the same mounting?

I'm keeping the coils on the motor as I want to sell motor complete with coils, loom, ecu etc

Or are you referring to the coilovers?

Edited by AMR33
30 minutes ago, Adz2332 said:

sorry meant the coilovers

pretty sure coupes and sedans are the same. The difference is between gtst and gtr/gts4, but I'm happy to be corrected on this

asking $800 ONO for the coilovers

21 hours ago, AMR33 said:

pretty sure coupes and sedans are the same. The difference is between gtst and gtr/gts4, but I'm happy to be corrected on this

asking $800 ONO for the coilovers

 

how old are they? which BC model are they??

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now



  • Similar Content

  • Latest Posts

    • Pads for R32 GTS-t, R32 GT-R non V-Spec (Sumitomo), R33 GTS-t and R34 GT-t are all interchangeable. R34 GT uses a 2x piston caliper, hence it didn't fit.
    • Checked with amayama and nope, the full S2 manual set is not available anymore. Unsurprising, but still disappointing as the ? on availability gave a glimmer of hope.
    • I've heard the Tomei USA head gaskets are decent if you want to o-ring the heads but otherwise not recommended.
    • The 296mm rotors are the R33 turbo brakes. The 310mm rotors are the R34 turbo brakes. The calipers are nearly the same, but not. They're the same caliper but the R34 caliper has longer legs so that it sits out far enough to go over the rotor. The pads are the same for both. When you say, "I bough tsome EBC"....did you just mean pads? Or rotors? 310mm rotors fit under 17" wheels. There may be some wheels without enough clearance though. I can't fit my fingers between the barrel of my wheel and the "corners" of my R34 calipers, but there is plenty of room behind the spokes. This is on Enkei RPF1. You can fit 324mm rotors inside a 17" wheel, but I'd be willing to bet that it would be close to impossible with the Nissan/Sumitomo caliper (using an adapter, of course), because the Sumitomo caliper is fatter than the Brembo caliper that is supposed to go on the 324mm rotors.
    • Hi. Can someone tell me what brakes(and mainly WHERE) can i buy brakes on R34 GTT? I bought some EBC which SHOULD go on my car(i have GT but it has GTT brakes) but it does not fit, Brakes are "too" small(296mm) Are 310mm be good or? I have 17 inch wheel so no "big boys" but for me driving i just need one that fits and i can get here in EU/Czech.
×
×
  • Create New...