Jump to content
SAU Community

Recommended Posts

Hey All,

I have checked the forum but just get a heap of for sale posts. I know the pros and cons of raising the boot rear but I had a few other questions. 

- should I use a spring washer and if so, where exactly in relation to the hood and hood plate and other washers?

- should I use a rubber/nylon washer and if so, where in relation to the hood and hood plate and other washers?

- should I stagger the number of spacers between the front and rear hood panel bolts so that they keep the angle of the bonnet or mount flat on the same number of washers for both?

- should I take the coil pack cover off in addition and if so where is a good spot for the igniter?

 

Thanks guys. 

Btw I have just changed gearbox and rear diff oil to redline lightweight and motul gearbox competition - best money I have spent on the car so far wow!

 

It's not 1975 any more. Why would you want to do this? You do appreciate that the base of the windscreen is a high pressure area, not a low pressure area, and the whole idea behind lifting the rear of the bonnet to let out out of the engine bay is invalidated by that fact? Right?

And don't take the coil pack cover off. Look inside the back of the timing cover. See the slots there? There is actually a deliberate effort made by Nissan for the cam drive system to pump some air through the coil tunnel. Take the cover off and you lose that. And you have to find some other method to mount the ignitoe, which you wouldn't have to do if you didn't remove the cover.

If my Splitfires die, and I don't feel like spending ~$1k for R35 type coils, the Yaris coils would be what I would do.

They are better coils, but not massively better. The R35/Audi/etc coils are quite a big step up though.

And, don't be fooled by the kits that say "Genuine Bosch Yaris Coils". The coils may be made by Bosch.....but genuine Yaris coils were made for Toyota by Denso. The Bosch ones are effectively aftermarket. I can't tell you that they are as good as the Denso ones.

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • HFM BM57 has a "bad" knee point, IIRC. It's not the same thing as the later R chassis MC.
    • The ATTESSA is functionally identical to R34; there were a bunch of JDM models that continued ATTESSA including Fuga/Q70, Skyline/Q50, Cima etc as an option. All with Auto only and I think mostly for snow regions. AFAIK there were no AWD VR30DDTT sold in Australia - it is on my to do list to check regs for racing a LHD car in Targa/ATR/AASA/CAMS events because if I can get the auto to work it would be interesting to run a 4wd car The Ecuteck TCM tuning is the same model as their ECU tuning, they already have it for R35 and Dose's favourite, BMW. You buy "points" to allow your computer to be tuned, buy either a bluetooth (phone app) or bluetooth+USB+Key (phone and PC) dongle, and pay for a tune that will be locked to your tuner ( ). You can also access the tuning software yourself but 1. it is mega expensive and 2. these computers have a billion parameters that intersect, so how could you ever spend enough time on it to get a decent result.
    • Or, is it a case of what it is like owning an R series Skyline? NFI what the previous owner has done or fiddled with... Ha ha ha After reading through this thread, I went on a bit of a research about the Q50/Q60. Now I'm quite intrigued by them! Is the AWD in them more like a WRX where it's always AWD, or is it more like the ATTESSA in the GTRs? By the sound of this TCU tuning, this sounds like a case of someone has made some real software for it, and you just need the right piece of hardware, and then you license that specific vehicle/TCU. Or is this a case of the software will be really expensive so only a few tuners have it, and you still have to pay a license per vehicle?
    • By popular demand.. it was a coil. Got my hands on 1 new OEM coil, replaced with the one that made the less noise difference when I unplugged it while the car was running and started the car up. No stutter and the engine light was gone. I guess I’ll buy the other 5 they have lol
    • No, code 21 is very straightforward. It can only be the things described in that diagnostic flow. In fact it has no way of knowing that the spark plug resistance is out of spec.
×
×
  • Create New...