Jump to content
SAU Community

Recommended Posts

I've heard a rubbing when I steer sometimes - It was not until I was under the car this weekend that I figured out what the issue is .. My LHS front wheel is rubbing up against the stabilizer front bar, not hard on it but enough to rub against it.  Whereas my RHS does not rub against anything.  Any idea what may be causing this is there something to adjust?   The tyres are brand new 225/50R16. See the photos for a clearer explanation. You can see how close the tire is and the rubbing mark.

20191116_125156.jpg

20191116_125229.jpg

Link to comment
https://www.sau.com.au/forums/topic/479194-tyre-rubbing-r32-gts-t/
Share on other sites

That's your caster rod/ radius rod.

Basically, the tyre is to wide for the offset of your wheels.  You may have previously had tyres the "same" size but in practice different tyre manufacturers have different actual tyre sizes for a nominated size like 225/50r16

Easiest solution, assuming you have plenty of thread on your wheel nuts, is to add a 5mm alloy spacer, which will push the wheel out 5mm, assuming they are legal where you are.

Spacers are not legal in Oz.

Wheels that fit correctly are the best solution - assuming that the wheels that you have are the wrong offset.

If the wheels are fine, you may find that you have something bent in the front end.

No, we cannot diagnose that sort of thing from photos.

What wheels are on the car. Width and offset.

 

5 hours ago, Strexx said:

Thanks guys but the new tyres are exactly the same size as the old tyres I just replaced - Is the 5mm space legal in NSW?  If I do not use the space or if I do for that matter will this impede my Blue Slip?

Are spacers the only fix?

Did you read Duncan's answer regarding differences in actual size versus nominal size among manufacturers? Are your new tyres the same brand and type (and sourced from the same factory/country) as your previous tyres? Do you have stock wheels and if not what is the width and offset of your current wheels? Another possibility is that you have whacked a kerb with that wheel and damaged the suspension.

Spacers are not the only fix. Other solutions are different wheels, tyres, or lock stops.

So being new to this scene - I have no idea what offsets are. I can tell you that the last set of tyres I had on the car were all of a different brand! Yes all my new tyres are same brand, same size, same batch, RS4'sall bought at the same time. The wheel sizing is 16 x 6 1/2 JJ 40 - It's my understanding these are genuine - are they? (See photo with old tyres) In hindsight when the tyres were fitted the wheels were balanced and one wheel was slightly buckled. (On their advice it's on on the rear).  So if it has had a hit - How can I identify what is outta whack and what needs to be replaced?20191102_085640.thumb.jpg.935b55e8c04ca57e5f9c773d4820b233.jpg

Those are standard wheels and you should not have rubbing problems with those tyres on that wheel.

Control arm bushes could be stuffed, upper arm bushes are probably completely rooted. Both of these could cause the upright to lean the wrong way. it could have taken a hit into a kerb and moved the subframe under the chassis rails. You'd be best off taking it to a (good) wheel aligner to see if they can work it out.

225/50 too fat for 6.5 (it's for standard GT-R 16x8 wheels IIRC), should be 205/55. But shouldn't have rubbing issues.

Standard R32 GTS-t wheels are +40, perhaps tyres are deflecting too much? Looks like your car is lowered so geometry would be off.

Most likely something is bent.

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • If as it's stalling, the fuel pressure rises, it's saying there's less vacuum in the intake manifold. This is pretty typical of an engine that is slowing down.   While typically is agree it sounds fuel related, it really sounds fuel/air mixture related. Since the whole system has been refurbished, including injectors, pump, etc, it's likely we've altered how well the system is delivering fuel. If someone before you has messed with the IACV because it needed fiddling with as the fuel system was dieing out, we need to readjust it back. Getting things back to factory spec everywhere, is what's going to help the entire system. So if it idles at 400rpm with no IACV, that needs raising. Getting factory air flow back to normal will help us get everything back in spec, and likely help chase down any other issues. Back on IACV, if the base idle (no IACV plugged in) is too far out, it's a lot harder for the ECU to control idle. The IACV duty cycle causes non linear variations in reality. When I've tuned the idle valves in the past, you need to keep it in a relatively narrow window on aftermarket ecus to stop them doing wild dances. It also means if your base idle is too low, the valve needs to open too much, and then the smallest % change ends up being a huge variation.
    • I guess one thing that might be wrong is the manifold pressure.  It is a constant -5.9 and never moves even under 100% throttle and load.  I would expect it to atleast go to 0 correct?  It's doing this with the OEM MAP as well as the ECU vacuum sensor. When trying to tune the base map under load the crosshairs only climb vertically with RPM, but always in the -5.9 column.
    • AHHHH gotchaa, I'll do that once I am home again. I tried doing the harness with the multimeter but it seems the car needed a jump, there was no power when it was in the "ON" position. Not sure if I should use car battery jump starter or if its because the stuff that has been disconnect the car just does send power.
    • As far as I can tell I have everything properly set in the Haltech software for engine size, injector data, all sensors seem to be reporting proper numbers.  If I change any injector details it doesnt run right.    Changing the base map is having the biggest change in response, im not sure how people are saying it doesnt really matter.  I'm guessing under normal conditions the ECU is able to self adjust and keep everything smooth.   Right now my best performance is happening by lowering the base map just enough to where the ECU us doing short term cut of about 45% to reach the target Lambda of 14.7.  That way when I start putting load on it still has high enough fuel map to not be so lean.  After 2500 rpm I raised the base map to what would be really rich at no load, but still helps with the lean spots on load.  I figure I don't have much reason to be above 2500rpm with no load.  When watching other videos it seems their target is reached much faster than mine.  Mine takes forever to adjust and reach the target. My next few days will be spent making sure timing is good, it was running fine before doing the ECU and DBW swap, but want to verify.  I'll also probably swap in the new injectors I bought as well as a walbro 255 pump.  
    • It would be different if the sealant hadn't started to peel up with gaps in the glue about ~6cm and bigger in some areas. I would much prefer not having to do the work take them off the car . However, the filler the owner put in the roof rack mount cavities has shrunk and begun to crack on the rail delete panels. I cant trust that to hold off moisture ingress especially where I live. Not only that but I have faded paint on as well as on either side of these panels, so they would need to come off to give the roofline a proper respray. My goal is to get in there and put a healthy amount of epoxy instead of panel filler/bog and potentially skin with carbon fiber. I have 2 spare rolls from an old motorcycle fairing project from a few years back and I think it'd be a nice touch on a black stag.  I've seen some threads where people replace their roof rack delete with a welded in sheet metal part. But has anyone re-worked the roof rails themselves? It seems like there is a lot of volume there to add in some threads and maybe a keyway for a quick(er) release roof rack system. Not afraid to mill something out if I have to. It would be cool to have a cross bar only setup. That way I can keep the sleek roofline that would accept a couple bolts to gain back that extra utility  3D print some snazzy covers to hide the threaded section to be thorough and keep things covered when not using the rack. 
×
×
  • Create New...