Jump to content
SAU Community

Getting fuel level signal into the ECU

Murray_Calavera
 Share

Recommended Posts

  • 4 weeks later...
  • Replies 156
  • Created
  • Last Reply

Top Posters In This Topic

Popular Days

Top Posters In This Topic

Popular Days

Popular Posts

BK
BK

Did you get this sorted with the level readings ? Was thinking about doing this too in the Haltech on the current 32 build. The resistance values to work off are 90 - 0 ohms with the Nissans. In a 32

Murray_Calavera
Murray_Calavera

Ok this is the final, final update (hopefully).  So as I had a V1 Haltech IC7, my internal pullup resistor built into the dash for AVI 4 was only 1,000 Ohm. Using this resistor, I had a working v

Tobz
Tobz

I’ve got a 3D Racing Solutions dash coming on Monday hopefully. I’ll post results to see if they are any better.

Posted Images

SLVRBAKSLPZ Collaborator

SLVRBAKSLPZ

Posted
Posted
4 minutes ago, stellarimports said:

What were your voltage readings for empty and full? I am about to set this up with my powertune dash and platinum pro in my R33.

Check the previous page for the readings I had. I thought they seemed low but the other members had similar readings.

I used those and everything seemed fine, then some reason they weren't.

 

After a day the senders reading were 0 (on both the OEM and Haltech conditioner) from what I personally got from pulling the sender.

 

I went back to the voltage numbers from the how to write-up article and the level read numbers and close to the level I had which was nearly full.

From memory the article number were 0.27 full/1.31 half/2.53 empty.

 

I was pissed cause all the work to pull that sender out and get the reading and it didn't work as planned for me. I cleaned the sender rail and everything. Idk why it reverted to the higher readings.

 

So I'd say to u, use both sets of reading and see what works for u.

 

To add I think the haltech sender died. Maybe got fuel in it. I will check to see if it works again after my work trip, but the oem seems to work better imo.

  • 1 month later...
DaymoR32 Proficient

DaymoR32

Posted
Posted (edited)

Hey guys,

Im having an issue with the fuel level on my IC-7 too.

I go into input calibration and try to input a range of values say for example 2.4v empty and 0 volts full. i then click apply and it automatically changes these values to 0.924v empty and 0.16 volts full. 

It also wont let me disable the pullup resistor either. i tried disabling just to see if it made a difference. 

I filled my tank up to the brim and ive done about 120km's and my tank still says 100% full. so either my car is now the most fuel efficient car in the world or theres something wrong.

I'm using AVI input 1 sensor pin 18 with the 90-0 ohm fuel sensor channel.

Anyone have any ideas?

Car is an R32 GTS-T with a hlatech elite 2500 ECU - which shouldnt really make any difference i dont believe

 

Edited by DaymoR32
SLVRBAKSLPZ Collaborator

SLVRBAKSLPZ

Posted
Posted
2 hours ago, DaymoR32 said:

Hey guys,

Im having an issue with the fuel level on my IC-7 too.

I go into input calibration and try to input a range of values say for example 2.4v empty and 0 volts full. i then click apply and it automatically changes these values to 0.924v empty and 0.16 volts full. 

It also wont let me disable the pullup resistor either. i tried disabling just to see if it made a difference. 

I filled my tank up to the brim and ive done about 120km's and my tank still says 100% full. so either my car is now the most fuel efficient car in the world or theres something wrong.

I'm using AVI input 1 sensor pin 18 with the 90-0 ohm fuel sensor channel.

Anyone have any ideas?

Car is an R32 GTS-T with a hlatech elite 2500 ECU - which shouldnt really make any difference i dont believe

 

I have a Plat Pro. i didnt have issues it any auto correction of the values or the resistor button being locked out

DaymoR32 Proficient

DaymoR32

Posted
Posted
19 minutes ago, SLVRBAKSLPZ said:

I have a Plat Pro. i didnt have issues it any auto correction of the values or the resistor button being locked out

the resistor button isnt locked out so to speak. i just change it on the drop down to "disabled" then click apply and its enabled again if that makes sense

SLVRBAKSLPZ Collaborator

SLVRBAKSLPZ

Posted
Posted
23 hours ago, DaymoR32 said:

the resistor button isnt locked out so to speak. i just change it on the drop down to "disabled" then click apply and its enabled again if that makes sense

So now I'm having the same issue as you. My sender stopped reading the other day as the full value changed. It doesn't set when pressing apply

I dont know why. I just did it out the blue

 

DaymoR32 Proficient

DaymoR32

Posted
Posted
25 minutes ago, SLVRBAKSLPZ said:

So now I'm having the same issue as you. My sender stopped reading the other day as the full value changed. It doesn't set when pressing apply

I dont know why. I just did it out the blue

 

so is yours saying 100% full aswell? what voltage values have you used for full and empty? and did you put more than 2 columns worth of data in?

I've tried having 2 columns. i.e 2.4v - 0% & 0v - 100%

Then ive also tried 6-7 colums with 0, 20%, 40%, 60%, 80%, 100% etc

It still reverts back to two columns and random values when i click apply

SLVRBAKSLPZ Collaborator

SLVRBAKSLPZ

Posted
Posted
1 minute ago, DaymoR32 said:

so is yours saying 100% full aswell? what voltage values have you used for full and empty? and did you put more than 2 columns worth of data in?

I've tried having 2 columns. i.e 2.4v - 0% & 0v - 100%

Then ive also tried 6-7 colums with 0, 20%, 40%, 60%, 80%, 100% etc

It still reverts back to two columns and random values when i click apply

Full was 0.27 / half 1.31 / E 2.53

 

Just full changed.

 

I kinda fixed it. So I have a haltech fuel sender conditioner still wired. I think it died from getting gas in it from pulling the sender, but I had it wired up still. I pulled the power wire off for it which seemed to have made the OEM sender signal stick to full. Once I put the power from the conditioner to the battery, It started reading 15gals.

However the ICC software still reads 0.01 and revert while trying to change 

DaymoR32 Proficient

DaymoR32

Posted
Posted
3 minutes ago, SLVRBAKSLPZ said:

Full was 0.27 / half 1.31 / E 2.53

 

Just full changed.

 

I kinda fixed it. So I have a haltech fuel sender conditioner still wired. I think it died from getting gas in it from pulling the sender, but I had it wired up still. I pulled the power wire off for it which seemed to have made the OEM sender signal stick to full. Once I put the power from the conditioner to the battery, It started reading 15gals.

However the ICC software still reads 0.01 and revert while trying to change 

hmmm, i dont have a haltech fuel sender conditioner in mine. im just taking it straight from the fuel level wire that went to the original dash.

I originally had the fuel going into pin 21 as per the wiring diagram but that just didnt work at all and could not be calibrated for some reason. theres sesor and diagnostic for each avi input apar from on avi 4.

I really dont understand why its not working when it worked fine on the Racepak IQ3

SLVRBAKSLPZ Collaborator

SLVRBAKSLPZ

Posted
Posted
Just now, DaymoR32 said:

hmmm, i dont have a haltech fuel sender conditioner in mine. im just taking it straight from the fuel level wire that went to the original dash.

I originally had the fuel going into pin 21 as per the wiring diagram but that just didnt work at all and could not be calibrated for some reason. theres sesor and diagnostic for each avi input apar from on avi 4.

I really dont understand why its not working when it worked fine on the Racepak IQ3

Mine is set to pin 18. Mine worked fine as well. Idl what to make of it.

This calls for an email to Haltech

 

DaymoR32 Proficient

DaymoR32

Posted
Posted
3 minutes ago, SLVRBAKSLPZ said:

Mine is set to pin 18. Mine worked fine as well. Idl what to make of it.

This calls for an email to Haltech

 

one more thing that i havent tried, is modifying the dash when its not plugged in. basically load your layout from the dash > unplug > change settings > plug dash back in > send to dash.

Maybe that will work....

SLVRBAKSLPZ Collaborator

SLVRBAKSLPZ

Posted
Posted
1 minute ago, DaymoR32 said:

one more thing that i havent tried, is modifying the dash when its not plugged in. basically load your layout from the dash > unplug > change settings > plug dash back in > send to dash.

Maybe that will work....

I tried that too.

 

Even loaded my old file from January. Still reverts. And I just updated the firmware today so i know it wasn't that

  • Like 1
SLVRBAKSLPZ Collaborator

SLVRBAKSLPZ

Posted
Posted
14 minutes ago, SLVRBAKSLPZ said:

I tried that too.

 

Even loaded my old file from January. Still reverts. And I just updated the firmware today so i know it wasn't that

..... It may be the new software update.

 

I loaded the new update on my laptop a week or two ago. I didn't use it til today. Tryna change it offline with my old file and it's not saving settings.

I'm emailing Haltech now.

DaymoR32 Proficient

DaymoR32

Posted
Posted
9 minutes ago, SLVRBAKSLPZ said:

..... It may be the new software update.

 

I loaded the new update on my laptop a week or two ago. I didn't use it til today. Tryna change it offline with my old file and it's not saving settings.

I'm emailing Haltech now.

thats another possibilty as ive only used the latest haltech software!

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now
 Share
Go to topic listing


  • Similar Content

  • Latest Posts

    • The Bogan
      Torana Lx Gtr Hatch, Lots Of Pictures

      By The Bogan · Posted

      LOL, when one "money pit" is never enough Noice, and excellent work mate
    • The Bogan
      NC MX5

      By The Bogan · Posted

      I have more than enough digging, laying blocks, moving gravel, airrating, feeding and top soiling the grass, and setting up the veggie gardens growing some seedlings,  and then removing all the unused rock to keep me busy for the next few months at least,  hopefully the rain stops soon so I can get a few hours in this arvo, but, before that Sunday is washing day, is every body happy, you bet your life we are Nice country road day drives are a day off whenever I'm muscle sore from all the landscaping at the moment, but, more epic multiple day drives will start once the majority of the big jobs outside are completed
    • MBS206
      NC MX5

      By MBS206 · Posted

      I hear that would involve some nice country road drives into the hills for Mark...
    • MBS206
      Recommendation for engine oil funnel spill free

      By MBS206 · Posted

      I thought I'd come back and add something I JUST learned. A Toyota LandCruiser with a 1HZ, mates perfectly with a bottle of Nulon brake fluid. As in, it perfectly screws in. Great make shift funnel when you cut the bottom of it off. This may work for your Corolla.   Unfortunately, tipping a 10L drum is much harder than a 4 to 6L bottle, and they no longer include the easy pour tap which was just perfection to use previously.  
    • EndZee
      Fuel Pump Control Module & Dropping Resistor

      By EndZee · Posted

      Guys since i bought r33 gts25t coupe 1994 automatic a/t(manual swap 350z gearbox)  all i got is problems, always problems. Lets start with that when i turn key into ignition(ON) fuel pump doesnt always works. Sometimes i have to turn key twice Off/on/off/on until it primes. Its new, dw300 - 340lph. My gearbox broke so i did gearbox swap, install different intake manifold, injectors and i take pipes. Car was sitting in garage for more than half a year. I did assembly all not that long ago and when i turn ignition cant hear prime. All of sudden it stopped working. Theres many videos on YouTube how to make relay mod on r33 straight from battery so i did and it doesnt work! 😰 30 - battery positive  87 - positive from fuel pump to relay 85, 86 - one of two wires from original fuel pump wires(light blue, grey) and it didn’t work. so I check on ignition and took original BLUE relays wires from trunk, next to fuses. (I believe it’s IGN+ and ECU pin 18. it didn’t work…  tried connecting (IGN+ from og relay) and (ECU 104 from 1of4 FPCM wires) to my new relay 85/86 and it didn’t work.  I unplug FPCM. Didn’t work. im thinking what’s wrong   fuel pump is working, if I leave IGN+ on 85 and 86 straight to ground it works but it’s just nonstop. Since it getting constant 12v after key in ON. light blue wire gives me 6-8v.  so how this should be connected? What causing ECU not giving — on pin? Or I did sth wrong and that’s why it doesn’t work? I need negative signal on ECU that control fuel pump. What this should be?
×
×
  • Create New...