Jump to content
SAU Community

Recommended Posts

Hi,

see items below for sale - all items are used 

All items are negotiable - can freight at the buyers expense  or pickup

Located in Griffith NSW 2680

Photos Attached 

Standard R33 GTR Turbo set - includes manifolds and heatsheilds, only has 1 stainless down pipe. Minimal shaft play 

Manifolds do have holes in them due to EGT sensors being fitted previously - one hole per manifold 

Looking for $120.00 for the pair  

 

R32 GTR Drivers side A/C Vent - was removed to fit a gauge 

$25.00

 

Standard RB26 Valve Springs with Retainers 

Came out of a Nissan reproduction engine so not many KM's on them 

$40.00

 

Standrad RB26 Camshafts intake and exhaust 

Came out of a nissan reproduction engine so not many KM's on them

No Picture 

Looking for $80.00 for the pair 

R32 GTR A/C Condesnor Fan 

Tested Still in working order 

$65.00

 

CUSCO Radiator Cooling Panel R32 GTR

Like New , has a few minor scratches and a rub mark in the RH corner 

$45.00

 

R32 GTR Speedo Cluster 340KM

Bad Points - KM Count has gone crazy/ Not reading correctly , speedo works fine and Front Torque gauge dosent Work 

$70.00

 

 

 

 

thumbnail_IMG_6984.jpg

thumbnail_IMG_6983.jpg

thumbnail_IMG_6982.jpg

thumbnail_IMG_6981.jpg

thumbnail_IMG_6980.jpg

thumbnail_IMG_6979.jpg

thumbnail_IMG_6978.jpg

thumbnail_IMG_6977.jpg

thumbnail_IMG_6976.jpg

Edited by nismo32gtr
Link to comment
https://www.sau.com.au/forums/topic/480459-gtr-parts-turbos-speedo-etc/
Share on other sites

  • 3 weeks later...
  • 4 weeks later...

Also i have the below for sale 

R32 GTR Passenger Side Reverse Light $25.00 

Good condition no cracks - will come up good with a cleanup 

 

R32 GTR Headlights LH & RH $100.00 for the pair 

Good condition usual wear and tear for there age - black paint on top coming away and rear bulb boots cracked 

Grill Brackets NOT Damaged

These are NOT  N1 they are the standard Projector style 1989 units 

 

R32  GTR Centre Console Gauge Assembly $80.00

Was in working order when removed 

 

Cant upload photo's at the moment - but i can supply upon request 

Edited by nismo32gtr
4 hours ago, Robzilla32 said:

I will take the headlights please if you can ship to Melbourne

Hi Robzilla32 

Yes i can ship to melbourne at your cost - i would say they would be around $25-$30 to post 

  • 4 weeks later...

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • @Murray_Calavera  If I were an expert I wouldn't be in here looking for assistance.  I am extremely computer literate, have above average understanding on how things should be working and how they should tie together.  If I need to go to a professional tuner so be it, but I'd much rather learn and do things myself even if it means looking for some guidance along the way and blowing up a few engines. @GTSBoy  I was hoping it would be as simple as a large vacuum leak somewhere but I'm unable to find anything, all lines seem to be well capped or going where they need to be, and when removed there is vacuum felt on the tube.  It would be odd for the Haltech built in MAP to be faulty, the GTT tune I imported had it enabled from the start, I incorrectly assumed it was reading a signal from the stock MAP, but that doesn't exist.  After running a vacuum hose to the ECU the signal doesn't change more than 0.2 in either direction.   I'll probably upload a video of my settings tomorrow, as it stands I'm able to daily drive, but getting stuttering when giving it gas from idle, so pulling away from lights is a slow process of revving it up and feathering the clutch until its moving, then it will accelerate fine.  It sounds like I need to get to the bottom of the manifold pressure issue, but the ignition timing section is most intimidating to me and will probably let a pro do that part.  Tomorrow I'll try a different vacuum line to T off of, with any luck I selected one that was already bypassed during the DBW swap. @feartherb26  I do have +T in the works but wanted to wait until Spring to start with that swap since this is my good winter AWD vehicle.  When removing the butterfly, did it leave a bunch of holes in the manifold that you needed to plug?  I thought about removing it but assumed it would be a mess.   I notice no difference when capping the vacuum line to it or letting it do its thing.  This whole thing has convinced me to just get a forward facing manifold when the time comes though.
    • Update: tested my spark plugs that are supposed to be 5ohms with a 10% deviation and one gave me a 0 ohms reading and the rest were 3.9ohm<, so one bad and the others on their way out.
    • 9" wheels are a little too wide for a RWD 32. They can fit. People have put R33 GTR wheels on 32s for years and years. But they are a very tight squeeze. This has been known for about 30 years. As I said - there is no difference between a 17 and an 18 in terms of what will fit. The rolling diameter needs to stay about the same as stock - not very much larger. If you increase that, you will start to have problems. If you increae rolling diamater at the same time as yo increase width, you will have problems earlier. as 9" wheels are pushing the boundaries already, you would need to be careful with tyre choice. I would put 8.5s on the front of mine, but would expect problems with 9s.
    • post up screen shots of your injector tables
    • Diagnostic flow for a code 21 says check signal at the ECU pins, on a voltmeter of some kind it should read 0.1V at idle, 0.12V cranking, 0.15-0.25V at 2000 rpm. Check each coil such that +1, -3 is infinite or very high resistance, -3, +2 should do the same. (-1, +3), (+3, -2), (+1, -2), and (-1, +2) should all be somewhere between 0 ohms and high resistance. If you trace the path from the coil pin all the way back to the ECU in the diagram the resistance you measure at the coil vs connected to the harness should be pretty much the same. 
×
×
  • Create New...