Jump to content
SAU Community

Recommended Posts

  • 2 weeks later...
On 07/11/2020 at 8:35 PM, Robzilla32 said:

I accidentally brought home a tranny once. Nobody believed that story either

Ye na tryinga to say I didn't mean to buy a car with a shit tone of problems. Still luv it, but Im not gonna be rushing into buying a car again anytime soon. 

See here's the thing. For the last 20 years R31s have been exclusively owned by people who only frequent Centrelink, the cheesecake shop and the bottle-o. Most of them can't even spell teeth, let alone say the word, let alone have more than 30% of their originals.

It hasn't led to R31s being very well looked after, for the most part.

  • Like 2
12 minutes ago, GTSBoy said:

See here's the thing. For the last 20 years R31s have been exclusively owned by people who only frequent Centrelink, the cheesecake shop and the bottle-o. Most of them can't even spell teeth, let alone say the word, let alone have more than 30% of their originals.

It hasn't led to R31s being very well looked after, for the most part.

yeah na like apprently the 1st owner was a complete junga, like theirs so many random things the car came with (no crack pipes 😢) such as silhouette tail light garnishes and a f**king street poll for an exhaust tip, but the junkie kept a really nice interior which is wot kinda sold me 

1 hour ago, mlr said:

Fark she is a vlean old girl

Nice score

Hahaha yeah man lean indeed, just gotta ignore the roof and rust spots in the body and boot, all that stuff is bound to empty my wallet sooner or later.

PS. (Don't have to answer this) but has anyone gotta trick to dealing with rust bubbles/rust in general, or are we all paying the cars weight in gold to get it fixed at the body shop 

IMG20201119185207.jpg

IMG20201119185635.jpg

IMG20201119185617.jpg

IMG20201119185412.jpg

IMG20201119185351.jpg

IMG20201119185231.jpg

Wire wheel and converter, then throw on some paint and bondo, finish with a nice rattle can finish.

Don't worry about the exterior, just give it a cut and polish.

That patina look is in, just need some wide steel rims painted black to finish the look.

  • Thanks 1
25 minutes ago, mlr said:

Wire wheel and converter, then throw on some paint and bondo, finish with a nice rattle can finish.

Don't worry about the exterior, just give it a cut and polish.

That patina look is in, just need some wide steel rims painted black to finish the look.

 

3 minutes ago, trel said:

Yeah as mlr says rub back to bare metal, rustoleum, prime, then rattle can that bitch. Nice 31 otherwise dude, brings back memories.

yeah cheers guys I think I got a good idea how imma tackel it, but should i do the whole panel (when dealing with the rust spots) or just rattle can the parts that need it and hope it blends nicely.

 

yeah na was thinking about chasing down some rims with decent offset (still decided about colour), but for now i figure its cheaper to hunt down some ti hubcaps and roll with those for now    

Depends how far you want to go with the car. Just do the spots if the rest of it looks ok, you'll know as you rub back how far you'll need to go anyway. Keep up the posts. Give her a nice detail and keep it clean, they're a really reliable car if it's in good order.

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • Hi, is the HKS  Tower Bar still available ? negotiable ? 🤔
    • From there, it is really just test and assemble. Plug the adapter cables from the unit into the back of the screen, then the other side to the car harness. Don't forget all the other plugs too! Run the cables behind the unit and screw it back into place (4 screws) and you should now have 3 cables to run from the top screen to the android unit. I ran them along the DS of the other AV units in the gap between their backets and the console, and used some corrugated tubing on the sharp edges of the bracket so the wires were safe. Plug the centre console and lower screen in temporarily and turn the car to ACC, the AV should fire up as normal. Hold the back button for 3 sec and Android should appear on the top screen. You need to set the input to Aux for audio (more on that later). I put the unit under the AC duct in the centre console, with the wifi antenna on top of the AC duct near the shifter, the bluetooth antenna on the AC duct under the centre console The GPS unit on top of the DS to AC duct; they all seem to work OK there are are out of the way. Neat cable routing is a pain. For the drive recorder I mounted it near the rear view mirror and run the cable in the headlining, across the a pillar and then down the inside of the a pillar seal to the DS lower dash. From there it goes across and to one USB input for the unit. The second USB input is attached to the ECUtec OBD dongle and the 3rd goes to the USB bulkhead connected I added in the centre console. This is how the centre console looks "tidied" up Note I didn't install the provided speaker, didn't use the 2.5mm IPod in line or the piggyback loom for the Ipod or change any DIP switches; they seem to only be required if you need to use the Ipod input rather than the AUX input. That's it, install done, I'll follow up with a separate post on how the unit works, but in summary it retains all factory functions and inputs (so I still use my phone to the car for calls), reverse still works like factory etc.
    • Place the new daughterboard in the case and mount it using the 3 small black rivets provided, and reconnect the 3 factory ribbon cables to the new board Then, use the 3 piggyback cables from the daughterboard into the factory board on top (there are stand offs in the case to keep them apart. and remember to reconnect the antenna and rear cover fan wires. 1 screw to hold the motherboard in place. Before closing the case, make a hole in the sticker covering a hole in the case and run the cable for the android unit into the plug there. The video forgot this step, so did I, so will you probably. Then redo the 4 screws on back, 2 each top and bottom, 3 each side and put the 2 brackets back on.....all ready to go and not that tricky really.      
    • Onto the android unit. You need to remove the top screen because there is a daughterboard to put inside the case. Each side vent pops out from clips; start at the bottom and carefully remove upwards (use a trim remover tool to avoid breaking anything). Then the lower screen and controls come out, 4 screws, a couple of clips (including 3 flimsy ones at the top) and 3 plugs on the rear. Then the upper screen, 4 screws and a bunch of plugs and she is out. From there, remove the mounting brackets (2 screws each), 4 screws on the rear, 2 screws top and bottom and 3 screws holding in the small plates on each side. When you remove the back cover (tight fit), watch out for the power cable for the fan, I removed it so I could put the back aside. The mainboard is held in by 1 screw in the middle, 1 aerial at the top and 3 ribbon cables. If you've ever done any laptop stuff the ribbon cables are OK to work with, just pop up the retainer and they slide out. If you are not familiar just grab a 12 year old from an iphone factory, they will know how it works The case should now look like this:
    • Switching the console was tricky. First there were 6 screws to remove, and also the little adapter loom and its screws had to come out. Also don't forget to remove the 2 screws holding the central locking receiver. Then there are 4 clips on either side....these were very tight in this case and needed careful persuading with a long flat screw driver....some force required but not enough to break them...this was probably the fiddliest part of the whole job. In my case I needed both the wiring loom and the central locking receiver module to swap across to the new one. That was it for the console, so "assembly is the reverse of disassembly"
×
×
  • Create New...