Jump to content
SAU Community

Recommended Posts

You can try 303 aerospace protectant that stuff works good on rubbers and plastic.

 

On 29/11/2021 at 8:35 PM, Duncan said:

those seals are available new from nissan

 

On 30/11/2021 at 5:59 AM, joshuaho96 said:

This thread reminded me to order them. LH side is discontinued for R33s, we’ll see if it ever comes back.

 

Do you guys have the part no. For the RH side rubber?

On 30/11/2021 at 1:21 PM, Duncan said:

I don't have the part# handy, but all 4 (LH/RH door and cabin side) seals are listed on efisolutions.com.au

https://www.efisolutions.com.au/search-results?q=r32 seal

Thanks duncan, im looking for R33 rubbers.

Can't seem to find the one that looks like the r32's, the only r33 i can find doesn't look like it goes around the side mirror.

On 11/29/2021 at 5:19 PM, dyl33 said:

You can try 303 aerospace protectant that stuff works good on rubbers and plastic.

 

 

 

Do you guys have the part no. For the RH side rubber?

It's listed on the EPC under "front door panel and fitting", original part number for the RH is 80220-22U00, LH is 80221-22U00. Should bring up the superceding part numbers. The LH is definitely discontinued but might come back under another part number at laughable cost under the Nismo Heritage Parts program, if they made the RH side as recently as last year they might do it for the LH side if they think they can sell out their MOQ. RH is an open question, I have no idea if they're still available but we'll see if my order goes through. To get that one stupid rubber piece you have to buy the entire assembly. In classic Nissan fashion the part was barely painted from the factory so they tend to be extremely rusty when pulled out of the door, so to do the repair "properly" you need to mask off the rubber and get it painted so it doesn't rust again. Looking around you should also expect to spend a lot of time with the door disassembled and adjusting it so the window slides correctly as it seems to be a guide rail for the pillarless windows.

This Minkara blog talks about the production dates on their parts, they mention that the driver side part run seems to be relatively recent (2020?) while the passenger side is much older, more like 2016: https://minkara.carview.co.jp/userid/322508/car/2941721/6237254/note.aspx

On 11/29/2021 at 6:21 PM, Duncan said:

I don't have the part# handy, but all 4 (LH/RH door and cabin side) seals are listed on efisolutions.com.au

https://www.efisolutions.com.au/search-results?q=r32 seal

The R32 has a different design, you only need the door rubber seal 80830-04U10 RH and 80831-04U10 LH instead of buying an entire structural component of the door like the R33. I don't really understand why Nissan didn't make the rubber weatherstripping a separate piece like the R32s even if they wanted to have the glass guide be a separate component in the door.

On 11/30/2021 at 5:28 PM, PLYNX said:

Toluene or Xylene will probably remove it

DON'T get it on anything else

As a general rule I thought hydrocarbons and rubber don't mix? I got a bunch of penetrating oil and other fun stuff on some old hoses as I was taking my engine apart and it was really obvious that it damaged them. I wouldn't risk taking anything like that to rubber I actually wanted to keep.

On 1/12/21 at 3:04 PM, PLYNX said:

You only need to wipe off the white "oxidization" off the surface of the rubber with a dampend cloth

You’re right. It’s been days since I wiped that spot and it’s still as per the “after” photo attached in my original post 😀

  • 1 month later...

AFAIK you can't replace only the rubber seal you need to buy the entire corner piece assembly. LHS is discontinued & RHS is available under a new part # H0220-22U00. Is that you Nissan Scam Program??

I've had great results restoring the rubber using a black vinyl dye product called Forever Black. 

 

spacer.png

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • Hi, is the HKS  Tower Bar still available ? negotiable ? 🤔
    • From there, it is really just test and assemble. Plug the adapter cables from the unit into the back of the screen, then the other side to the car harness. Don't forget all the other plugs too! Run the cables behind the unit and screw it back into place (4 screws) and you should now have 3 cables to run from the top screen to the android unit. I ran them along the DS of the other AV units in the gap between their backets and the console, and used some corrugated tubing on the sharp edges of the bracket so the wires were safe. Plug the centre console and lower screen in temporarily and turn the car to ACC, the AV should fire up as normal. Hold the back button for 3 sec and Android should appear on the top screen. You need to set the input to Aux for audio (more on that later). I put the unit under the AC duct in the centre console, with the wifi antenna on top of the AC duct near the shifter, the bluetooth antenna on the AC duct under the centre console The GPS unit on top of the DS to AC duct; they all seem to work OK there are are out of the way. Neat cable routing is a pain. For the drive recorder I mounted it near the rear view mirror and run the cable in the headlining, across the a pillar and then down the inside of the a pillar seal to the DS lower dash. From there it goes across and to one USB input for the unit. The second USB input is attached to the ECUtec OBD dongle and the 3rd goes to the USB bulkhead connected I added in the centre console. This is how the centre console looks "tidied" up Note I didn't install the provided speaker, didn't use the 2.5mm IPod in line or the piggyback loom for the Ipod or change any DIP switches; they seem to only be required if you need to use the Ipod input rather than the AUX input. That's it, install done, I'll follow up with a separate post on how the unit works, but in summary it retains all factory functions and inputs (so I still use my phone to the car for calls), reverse still works like factory etc.
    • Place the new daughterboard in the case and mount it using the 3 small black rivets provided, and reconnect the 3 factory ribbon cables to the new board Then, use the 3 piggyback cables from the daughterboard into the factory board on top (there are stand offs in the case to keep them apart. and remember to reconnect the antenna and rear cover fan wires. 1 screw to hold the motherboard in place. Before closing the case, make a hole in the sticker covering a hole in the case and run the cable for the android unit into the plug there. The video forgot this step, so did I, so will you probably. Then redo the 4 screws on back, 2 each top and bottom, 3 each side and put the 2 brackets back on.....all ready to go and not that tricky really.      
    • Onto the android unit. You need to remove the top screen because there is a daughterboard to put inside the case. Each side vent pops out from clips; start at the bottom and carefully remove upwards (use a trim remover tool to avoid breaking anything). Then the lower screen and controls come out, 4 screws, a couple of clips (including 3 flimsy ones at the top) and 3 plugs on the rear. Then the upper screen, 4 screws and a bunch of plugs and she is out. From there, remove the mounting brackets (2 screws each), 4 screws on the rear, 2 screws top and bottom and 3 screws holding in the small plates on each side. When you remove the back cover (tight fit), watch out for the power cable for the fan, I removed it so I could put the back aside. The mainboard is held in by 1 screw in the middle, 1 aerial at the top and 3 ribbon cables. If you've ever done any laptop stuff the ribbon cables are OK to work with, just pop up the retainer and they slide out. If you are not familiar just grab a 12 year old from an iphone factory, they will know how it works The case should now look like this:
    • Switching the console was tricky. First there were 6 screws to remove, and also the little adapter loom and its screws had to come out. Also don't forget to remove the 2 screws holding the central locking receiver. Then there are 4 clips on either side....these were very tight in this case and needed careful persuading with a long flat screw driver....some force required but not enough to break them...this was probably the fiddliest part of the whole job. In my case I needed both the wiring loom and the central locking receiver module to swap across to the new one. That was it for the console, so "assembly is the reverse of disassembly"
×
×
  • Create New...