Jump to content
SAU Community

C34 25det neo

Jarrod rb25det
 Share

Recommended Posts

Jarrod rb25det Newbie

Jarrod rb25det

Posted
Posted (edited)

Hey I've got a s2 c34 with rb25det neo after I installed a highflowed 25det turbo the car hesitates for a second between gears when coming off boost then back on throttle. I was running a frontmount no problems with the stock turbo and I've jst installed the sidemount and now it's fine again with the frontmount and highflowed turbo is the afm not coping with the extra air flow or what I'm stummped

Edited by Jarrod rb25det
Link to comment
https://www.sau.com.au/forums/topic/483484-c34-25det-neo/
Share on other sites
GTSBoy Grand Master

GTSBoy

Posted
Posted

Any larger turbo worth using will flow more at at "low boost" than the stock turbo does wound all the way up to "turbine flies off". You can't really go past the airflow available from the stock turbo at 10 psi without the stock ECU starting to get upset, and at 11-12 psi it will really be pissed off. I wouldn't contemplate a highflow on a stock ECU without Nistuning it to get around all that.

  • Like 1
Link to comment
https://www.sau.com.au/forums/topic/483484-c34-25det-neo/#findComment-7962435
Share on other sites
BK Grand Master

BK

Posted
Posted
On 24/03/2022 at 12:24 PM, Jarrod rb25det said:

Like I said I have a link g4x but havnt been able to tune it that's not my question anyway I'm jst cruising until it gets tuned but with the frontmount it buzzes out and the sidemount it doesn't that's my question 

I think you've just demonstrated how shit your side mount intercooler actually is in pressure drop and flow across its core compared to your front mount.

  • Like 2
Link to comment
https://www.sau.com.au/forums/topic/483484-c34-25det-neo/#findComment-7962446
Share on other sites
robbo_rb180 Grand Master

robbo_rb180

Posted
Posted

go back to the front mount, install the Link and road tune the low load stuff, plenty of people can help like myself or @Dose Pipe Sutututu
Depends where you live an experienced member may be able to help with the install & setup

 

  • Like 2
Link to comment
https://www.sau.com.au/forums/topic/483484-c34-25det-neo/#findComment-7962453
Share on other sites
robbo_rb180 Grand Master

robbo_rb180

Posted
Posted
On 3/25/2022 at 4:54 PM, Jarrod rb25det said:

I've now installed the link g4x calibrated everything set base timing and finally got it running afrs are rich on idle but fine cruising but ran out of daylight so will have to tidy things up tomorrow 

 

Good work
Easy to trim fuel, build a Lambda/afr target map and can use the quick tune function to get it pretty good quickly but need to turn off any other trim tables.

  • Like 1
Link to comment
https://www.sau.com.au/forums/topic/483484-c34-25det-neo/#findComment-7962515
Share on other sites

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now
 Share
Go to topic listing


  • Similar Content

  • Latest Posts

    • Kinkstaah
      Mistakes were made, my R34 Story

      By Kinkstaah · Posted

      God damnit. The only option I actually have in the software is the one that is screenshotted. I am glad that I at least got it right... for those two points. Would it actually change anything if I chose/used 80C and 120C as the two points instead? My brain wants to imagine the formula put into HPtuners would be the same equation, otherwise none of this makes sense to me, unless: 1) The formula you put into VCM Scanner/HPTuners is always linear 2) The two points/input pairs are only arbitrary to choose (as the documentation implies) IF the actual scaling of the sensor is linear. then 3) If the scaling is not linear, the two points you choose matter a great deal, because the formula will draw a line between those two points only.
    • GTSBoy
      Mistakes were made, my R34 Story

      By GTSBoy · Posted

      Nah, that is hella wrong. If I do a simple linear between 150°C (0.407v) and 50°C (2.98v) I get the formula Temperature = -38.8651*voltage + 165.8181 It is perfectly correct at 50 and 150, but it is as much as 20° out in the region of 110°C, because the actual data is significantly non-linear there. It is no more than 4° out down at the lowest temperatures, but is is seriously shit almost everywhere. I cannot believe that the instruction is to do a 2 point linear fit. I would say the method I used previously would have to be better.
    • GTSBoy
      DeAgostini 1/8 scale BNR32 Nissan Skyline GT-R Nismo

      By GTSBoy · Posted

      That's hilariously putrid!
    • GTSBoy
      R33 Fuel Pump & Brakes after alarm swap

      By GTSBoy · Posted

      When I said "wiring diagram", I meant the car's wiring diagram. You need to understand how and when 12V appears on certain wires/terminals, when 0V is allowed to appear on certain wires/terminals (which is the difference between supply side switching, and earth side switching), for the way that the car is supposed to work without the immobiliser. Then you start looking for those voltages in the appropriate places at the appropriate times (ie, relay terminals, ECU terminals, fuel pump terminals, at different ignition switch positions, and at times such as "immediately after switching to ON" and "say, 5-10s after switching to ON". You will find that you are not getting what you need when and where you need it, and because you understand what you need and when, from working through the wiring diagram, you can then likely work out why you're not getting it. And that will lead you to the mess that has been made of the associated wires around the immobiliser. But seriously, there is no way that we will be able to find or lead you to the fault from here. You will have to do it at the car, because it will be something f**ked up, and there are a near infinite number of ways for it to be f**ked up. The wiring diagram will give you wire colours and pin numbers and so you can do continuity testing and voltage/time probing and start to work out what is right and what is wrong. I can only close my eyes and imagine a rat's nest of wiring under the dash. You can actually see and touch it.
    • Kinkstaah
      Mistakes were made, my R34 Story

      By Kinkstaah · Posted

      So I found this: https://www.efihardware.com/temperature-sensor-voltage-calculator I didn't know what the pullup resistor is. So I thought if I used my table of known values I could estimate it by putting a value into the pullup resistor, and this should line up with the voltages I had measured. Eventually I got this table out of it by using 210ohms as the pullup resistor. 180C 0.232V - Predicted 175C 0.254V - Predicted 170C 0.278V - Predicted 165C 0.305V - Predicted 160C 0.336V - Predicted 155C 0.369V - Predicted 150C 0.407V - Predicted 145C 0.448V - Predicted 140C 0.494V - Predicted 135C 0.545V - Predicted 130C 0.603V - Predicted 125C 0.668V - Predicted 120C 0.740V - Predicted 115C 0.817V - Predicted 110C 0.914V - Predicted 105C 1.023V - Predicted 100C 1.15V 90C 1.42V - Predicted 85C 1.59V 80C 1.74V 75C 1.94V 70C 2.10V 65C 2.33V 60C 2.56V 58C 2.68V 57C 2.70V 56C 2.74V 55C 2.78V 54C 2.80V 50C 2.98V 49C 3.06V 47C 3.18V 45C 3.23V 43C 3.36V 40C 3.51V 37C 3.67V 35C 3.75V 30C 4.00V As before, the formula in HPTuners is here: https://www.hptuners.com/documentation/files/VCM-Scanner/Content/vcm_scanner/defining_a_transform.htm?Highlight=defining a transform Specifically: In my case I used 50C and 150C, given the sensor is supposedly for that. Input 1 = 2.98V Output 1 = 50C Input 2 = 0.407V Output 2 = 150C (0.407-2.98) / (150-50) -2.573/100 = -0.02573 2.98/-0.02573 + 47.045 = 50 So the corresponding formula should be: (Input / -0.02573) + 47.045 = Output.   If someone can confirm my math it'd be great. Supposedly you can pick any two pairs of the data to make this formula.
×
×
  • Create New...