Jump to content
SAU Community

Recommended Posts

Hi Everyone. 

So we've installed a HKS Step Pro VCam kit to my RB26 2.8L engine. (Dry sumped etc)

Head has had a full overhaul in the past - 1mm oversize valves, Shimless Buckets, 150psi aftermarket springs etc. 

So the issue i have is the VCam system can't advance unless the RPM is at 3500rpm or more. I have eliminated all electrical Issues / ECU control issues. 

The oil pressure feed line has been moved somewhere where there is plenty of oil (engine has a dry sump with heaps of pressure), and the VCam itself has been disassembled and checked thoroughly.

Could there be a chance the valve springs are too heavy for the VCam system to open the valves at lower RPM and oil pressure?

Anyone have any ideas? 

Thanks

Link to comment
https://www.sau.com.au/forums/topic/483648-hks-vcam-step-pro-issues/
Share on other sites

On 5/16/2022 at 9:06 AM, The Mafia said:

Could there be a chance the valve springs are too heavy for the VCam system to open the valves at lower RPM and oil pressure?

I can't see how that could be the case. All it has to do is rotate the camshaft, which the camshaft is already doing and already popping the valves open upon demand. The real counteracting force against the oil pressure is the return spring in the positioner itself, no? So, whilst it is difficult to blame the valve springs, your theory might, could, just possibly have something in it.

I suggest fitting a pressure gauge to the supply line close to the actuator and see what's what. Maybe the pressure there is disappointingly low until 3.5k.

We installed a pressure gauge right on the side of the cam cover, 40psi at idle couldn't move the cam. Had to increase the rpm to 3500rpm (100psi) and it started to move. 

I've asked so any people - No one is sure. 

On 16/05/2022 at 12:23 PM, r32-25t said:

When you opened the the cam gear did you tighten the back up with the cam installed in it and made sure the backing plate isn’t touch the cam at all?

I'll find out mate

Currently installing a V-Cam also. So following thread with interest.

In the instructions it does recommend an upgraded oil pump due to the pressure required by the vcam.

40 psi at idle is pretty stout though, can't imagine that being an issue if the flow is good.

 

For my own interest, how are you confirming that it is or is not opening the vcam ?

What are you using to control the vcam ?  Assume an ecu over the HKS control box ?

 

My only suggestion to help and I am sure you have looked at this is go through the o-rings(Cam cover ones especially).

If one is pinched, 40 psi at cam cover is going to result in a lot less to cam gear if you have a leak.

 

I agree with others above, the valve springs should have nothing to do with this.

 

On 16/05/2022 at 1:02 PM, Butters said:

Currently installing a V-Cam also. So following thread with interest.

In the instructions it does recommend an upgraded oil pump due to the pressure required by the vcam.

40 psi at idle is pretty stout though, can't imagine that being an issue if the flow is good.

 

For my own interest, how are you confirming that it is or is not opening the vcam ?

What are you using to control the vcam ?  Assume an ecu over the HKS control box ?

 

My only suggestion to help and I am sure you have looked at this is go through the o-rings(Cam cover ones especially).

If one is pinched, 40 psi at cam cover is going to result in a lot less to cam gear if you have a leak.

 

I agree with others above, the valve springs should have nothing to do with this.

 

Hey mate, we double checked the o-rings. One was pinched and we replaced it and it had the same behavior. 

Cam is being controlled with an Emtron KV8. To bypass all of the ECU side of things we connected the solenoid directly to 12v and ground and had the same result. Cam wouldn't move until 3500rpm on the trace in the ECU. 

Something is not right. It's frustrating that's for sure. 

On 16/05/2022 at 12:23 PM, r32-25t said:

When you opened the the cam gear did you tighten the back up with the cam installed in it and made sure the backing plate isn’t touch the cam at all?

Can confirm all of this went back together correctly 

On 5/16/2022 at 11:28 AM, The Mafia said:

Hey mate, we double checked the o-rings. One was pinched and we replaced it and it had the same behavior. 

Cam is being controlled with an Emtron KV8. To bypass all of the ECU side of things we connected the solenoid directly to 12v and ground and had the same result. Cam wouldn't move until 3500rpm on the trace in the ECU. 

Something is not right. It's frustrating that's for sure. 

 

So to be very specific . The KV8 is sending PWM to the negative side of the solenoid at a specific RPM say 2000 ?

Then you are reading the reluctor sensor on the side of the cam cover to see the advance ?

And not seeing a change in the cam until 3500rpm ?

 

Yep, that's it. ECU was reporting the cam angle.

A quick test to rule out solenoid control was to get a tail, plug it into the solenoid, and give it 12v and ground directly. It wouldn't move until 3500rpm and 100psi on the little gauge we had inbetween the line and the cam cover. Exact same behaviour as when the ECU was trying to control it. 

I was doing some data stuff on my car which is also dry sumped and we didn't want the engine running, so used a Subaru cam belt (15km long) and a dry sump mandrel on a power drill. This allowed us to spin the pump independently of the engine and log some data, and the drill can be located in a convenient location without some poor bastard on his back under the car.

Perhaps you could do this and see if there's any other weird shit going on? Overall oil pressure isn't your problem, so it's leaking out or you have a faulty solenoid. Alternatively there's something mechanical dragging on the gear, as above it's got nothing to do with valve springs.

  • Like 1
On 16/05/2022 at 4:48 PM, Komdotkom said:

I was doing some data stuff on my car which is also dry sumped and we didn't want the engine running, so used a Subaru cam belt (15km long) and a dry sump mandrel on a power drill. This allowed us to spin the pump independently of the engine and log some data, and the drill can be located in a convenient location without some poor bastard on his back under the car.

Perhaps you could do this and see if there's any other weird shit going on? Overall oil pressure isn't your problem, so it's leaking out or you have a faulty solenoid. Alternatively there's something mechanical dragging on the gear, as above it's got nothing to do with valve springs.

Hi Mate, I have two VCam kits, we swapped the solenoid and that didn't help either.

We've ruled out quite a few things that's for sure. 

My money is still on an oil pressure drop post cam cover.

 

The other thing you have to question here is the data sampling and again I am sure you have done this but given we are running out of ideas :D

 

I am wondering if it is actually activating before 3500rpm and your only seeing the change in the data at the point.  Simple things like only log  after 3500 for all parameters :)

Are you holding the engine steady at 3000rpm for a period of time and activating the solenoid and seeing no change in the KV8 data ? 

On 17/05/2022 at 10:33 AM, Butters said:

My money is still on an oil pressure drop post cam cover.

 

The other thing you have to question here is the data sampling and again I am sure you have done this but given we are running out of ideas :D

 

I am wondering if it is actually activating before 3500rpm and your only seeing the change in the data at the point.  Simple things like only log  after 3500 for all parameters :)

Are you holding the engine steady at 3000rpm for a period of time and activating the solenoid and seeing no change in the KV8 data ? 

The sampling data was live mate. from idle to 3500. It's like the VCam couldn't move under 3500rpm (Oil pressure I'm thinking) because at 3500rpm the pressure at the guage was going over 100psi. Under that it couldn't control the position properly. 

When the oil was cold it was a little under 3500rpm which makes me think it's a pressure / flow / resistance (springs) issue. 

New springs are going in and I will report back. 

On 5/16/2022 at 9:59 PM, The Mafia said:

The sampling data was live mate. from idle to 3500. It's like the VCam couldn't move under 3500rpm (Oil pressure I'm thinking) because at 3500rpm the pressure at the guage was going over 100psi. Under that it couldn't control the position properly. 

When the oil was cold it was a little under 3500rpm which makes me think it's a pressure / flow / resistance (springs) issue. 

New springs are going in and I will report back. 

There is some kind of locking pin on the VVT cam gear that holds it in place during cold start and other conditions where the VVT is not going to work properly. So you're going to have to trace the path from the gauge to this pin and verify there's no weird behavior like leaks, etc.

Okay, so changed the valve springs and the VCT works as it should now (nice and responsive at idle). 

125psi springs were just too heavy for it. 

I have heard that when people have put heavier springs in the Barra those have stopped working too. 

Currently running HKS springs. 

I recommend lighter springs 90psi would be pushing it. 75psi or below will be my safe estimation.

(Please bear in mind your RPM targets, cam selections, etc). It's a careful balancing act. 

Edited by The Mafia
  • Like 1

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now



  • Similar Content

  • Latest Posts

    • Back again. I returned to Japan in Jul/Aug to spend time with the car on my birthday and remind myself what all the sacrifice and compromise is for. It happened to line up with the monthly morning meet in Okutama, which I have been wanting to go to for a long time. It's a unique event at a unique spot with really rare, interesting, and quirky cars. It's where all the oldheads and OGs gather. The nighttime scene at DKF certainly has its place and should be experienced if you're into cars, but there's too much bad attention and negativity around it now. IMO the better time is Sunday morning at DKF or Okutama; it's more chill and relaxed. I'm glad I was finally able to go, but not sure it's worth the drive from all the way from Nagoya immediately the day before, unless I was already staying in Tokyo for the days right before the meet, because you have to wake up quite early to make it in time. Funnily enough though I didn't drive the car all that much this trip because it was just too damn hot. While there were zero issues and running temps were nominal and the A/C was strong, RBs already run crazy hot as it is. Sure, it took it all like a champ but something about driving these cars in the ridiculous heat/humidity bothers me and makes me feel like I'm asking too much of it. I'm just me being weird and treating the car like a living thing with feelings; I'm mechanically sympathetic to a fault. Instead I was mainly driving something else around - a KX4(silver) 2001 X-Trail GT, that I acquired in May. There's a few different flavors to choose from with Xs, but visually it's the Nissan version of the Honda CR-V. Mechanically it's a whole different story as this, being the top-trim GT, has an SR20VET mated to a four speed auto and full-time AWD! It was a very affordable buy in exceptional condition inside and out, with very low mileage...only 48k kms. Most likely it was owned by an older person who kept it garaged and well-maintained, so I'm really happy with how it all worked out. It literally needs zero attention at the moment, albeit except for some minor visual touch-ups. I wanted something quirky, interesting, and practical and for sure it handily delivers on all three of those aspects. I was immediately able to utilize the cargo and passenger capacity to it's full extent. It's a lot of fun to drive and is quite punchy through 1st and 2nd. It's very unassuming -in the twisty bits it's a lot more composed than one would think at a glance- and it'll be even better once I get better tires on it(yes, it's an SUV but still a little boat-y for my liking). So...now I have two golden-era Nissans in silver. One sports car and one that does everything else; the perfect two-car solution I think👍 The rest of the trip...I was able to turn my stressed brain off and enjoy it, although I didn't quite get to do as much as I thought. I did some interesting things, met some interesting people, and happened into some interesting situations however, that's all for another post though only if people really want to know. Project-wise, I went back to Mine's again to discuss more plans and am hoping to wrap that up real soon; keep watching this space if that interests you. Additionally, while working in the tormenting sweatbox that is the warehouse, I was able to organize most of the myriad of parts that my friend is storing for me along with the cars, and the 34 has a nice little spot carved out for it: And since it can get so damn hot in there, that made it all the more easy to remove all the damn gauges that have mostly been an eyesore all this time. Huzzah. I was standing there looking at the car and said 'f**k it'. The heat basically makes the adhesive backing on the gauge mounts more pliable to work with, so it was far less stressful getting this done. I didn't fully clean it up or chase the wiring though; that will happen once I have the car in closer possession. Another major reason to remove all that stuff is to give people less reasons to get in my car and steal s**t while it's being exported/imported when/if the time comes, which leads us to my next point... ...and that is even though it's time in Japan is technically almost up since it's a November car and the X would be coming in March, I'm still not entirely sure where my life and career is headed; I don't really know what the future looks like and where I'm going to end up. I feel there's a great deal of uncertainty with me and as a result of that, it feels like I'm at a crossroads moreso now than any point in my life thus far and there are some choices I need to make. Yes, I've had some years to consider things and prepare myself, however too much has happened in that time to maintain confidence and everything feels so up in the air; tenuous one might say. Simply put, there's just too much nonsense going on right now from multiple vectors. Admittedly, I'm struggling to stay in the game and keep my eyes on the prize. So much so in fact, that very recently I came the closest I ever have before to calling it quits outright; selling everything and moving on and not looking back. The astute among you will pick up on key subtext within this paragraph. In the meantime I've still managed to slowly acquire some final bits for the car, but it feels nice knowing there's not much left to get and I'm almost across that finish line; I have almost everything I'll ever want for my interpretation and expression on what it is I think an R34 should be. 'til later.
    • Thanks for that, hadn’t used my brain enough to think about that. 
    • Also playing with fire if they start to flow more air down low than what the stock twins can. It's not even up top you need to worry, it can be at 3000rpm and part throttle and it's getting way more flow than it should.
    • Any G40/1000 or G40/1250 results out there?  
    • You still want a proper tune on the stock ECU though. Stock tune + stock ECU with GT-SS/-9s is probably playing with fire if you're running more than stock airflow/power.
×
×
  • Create New...