Jump to content
SAU Community

Thread stripped on wheel lug

PranK
 Share

Recommended Posts

PranK Grand Master

PranK

Posted
Posted

Ola SAU'ers.

I had the rear wheels off my car yesterday and one of the lugs just did not want to come off. I eventually forced it off and it looks like maybe it was cross threaded but then somebody used a gun to tighten it (for once it wasnt me who broke something). Maybe the alignment joint.

Anyhoo, the lug has no thread at all for the bottom 1" so I'm hoping the damage was done to this and not the hub itself. I dont want to just start threading something in there willy nilly so thought I'd check with you guys.

Maybe this is a "not me" fix in which case I can take it down the road.

How long can I drive on 4 lugs? 🤔

C

Link to comment
https://www.sau.com.au/forums/topic/484124-thread-stripped-on-wheel-lug/
Share on other sites
joshuaho96 Veteran

joshuaho96

Posted
Posted
6 minutes ago, PranK said:

Ola SAU'ers.

I had the rear wheels off my car yesterday and one of the lugs just did not want to come off. I eventually forced it off and it looks like maybe it was cross threaded but then somebody used a gun to tighten it (for once it wasnt me who broke something). Maybe the alignment joint.

Anyhoo, the lug has no thread at all for the bottom 1" so I'm hoping the damage was done to this and not the hub itself. I dont want to just start threading something in there willy nilly so thought I'd check with you guys.

Maybe this is a "not me" fix in which case I can take it down the road.

How long can I drive on 4 lugs? 🤔

C

I've driven a week on 4 lugs no problem. Probably don't push your luck much longer than that.

  • Like 2
PranK Grand Master

PranK

Posted
  • Author
Posted
1 minute ago, GTSBoy said:

Yeah, driving on 4 is why you have 5.

This is a poxy Eruo, no? Female thread is in the hub? Did you try one of the other bolts in there to see how it feels?

I gave a very half arsed (maybe even quarter arsed) attempt at putting another bolt in but I was a bit concerned about doing more damage.

That said, surely the hub steel is stronger than the bolts?

PranK Grand Master

PranK

Posted
  • Author
Posted

And yeah, female is in the hub. All other corners have had stud conversions but I needed to remove that conversion on this corner when I did the wheel bearing a few months back. Haven't put the studs back in since.

GeeDog Experienced

GeeDog

Posted
Posted

If you don't want a half-assed fix (and I think you don't), and don't have the correct tap, just get a "thread doctor" to come & fix it. They do this for a living, and will either just re-tap it or put in a helicoil. Might cost $100 - $150.

On the other hand, if you are just driving on the street, I suspect it would run forever on 4 studs. If you are still doing track days it's a different story.

  • Like 1
PranK Grand Master

PranK

Posted
  • Author
Posted

Yeah, I'm not comfortable with even the slightest chance something could go further wrong so I want it fixed ASAP. I went down to my tyre joint and i'm booked in for an alignment on Monday. They said they'd get their thread guy to come out and try and fix for me.

If I did this myself with a tap I don't think I'd ever listen to music in the car again, I'd be listening for wheel noises.

Appreciate the help guys.

  • Haha 3
Duncan Grand Master

Duncan

Posted
Posted

Don't worry about missing wheel nuts/bolts until the 3rd one fails. 4 will be fine indefinitely unless you are heading to the track.

But if I can just add, I know brand tradition is important, and I kind of get it with an over the top modernisation of a kidney shaped grille from the 70s....but using a wheel bolt is an arsehole of a way to locate and affix a wheel compared to a stud and nut

  • Like 3
PranK Grand Master

PranK

Posted
  • Author
Posted
16 hours ago, Duncan said:

But if I can just add, I know brand tradition is important, and I kind of get it with an over the top modernisation of a kidney shaped grille from the 70s....but using a wheel bolt is an arsehole of a way to locate and affix a wheel compared to a stud and nut

You have my 100% support here mate. Changing wheels sucks balls. That's why I did the stud conversion.

Bec's X5 has 20x12's on it. You should try holding those in place on a spinning front hub while you try to locate the hole for the fricken bolt. (Nobody raise the unnecessary size of those wheels please 😉 )

PranK Grand Master

PranK

Posted
  • Author
Posted

And the reason there's no studs in that hub now is because i needed to take them out to get the hub out of the wheel bearing when I replaced it. Also you can't adjust the handbrake with studs in :(

 

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now
 Share
Go to topic listing


  • Similar Content

  • Latest Posts

    • ARB26
      RB26DETT Sketchy boost mod?

      By ARB26 · Posted

      I might be way off the mark here.. there must be a T junction under the manifold. That takes manifold pressure through a check valve prior to the T, one side splits out to this bleed off orifice, the other straight to the wastegate actuators. 
    • ARB26
      RB26DETT Sketchy boost mod?

      By ARB26 · Posted

    • ARB26
      RB26DETT Sketchy boost mod?

      By ARB26 · Posted

      Carrying out some engine due diligence before my first drive in a 260RS that has been in storage for 10+ years, and found two lines that are susposed to be plumbed into the boost control solenoid. One of the lines (the wastegate boost supply line) to actuate the gates, had a bolt in one end blocking it. The other line (main boost signal line) from the very rear of the intake manifold (RB26DETT) and runs up to the boost controller had this pill in the end of it as seen in photos. Other than the obvious (T28 Ceramic turbos might well be cooked)  Can anyone shed any light on if there is any validity at all with this mod, bleeding a constant fixed rate of manifold boost pressure off through this 3mm hole?  Is it deliberate?  Was this a 90s Jap mod done to RB26's? Or has someone just fitted this without any idea of what happens to ceramic T28s if they are not gate controlled?    
    • PranK
      Chris' Toyota Mark ii JZX110

      By PranK · Posted

      This looks great! Awesome to have the 5 speed with an LSD in this. The Recaro's look like SR2's or SR3's. It's a shame they've been retrimmed as they would have looked sweet in their original colours. I think I'd want my agent to be a little more up front and informative too. I've never imported but I reckon it would make me a little nervous, so the more info the better.
    • soviet_merlin
      Duncan's V37.......race car?

      By soviet_merlin · Posted

      Thanks for doing that Duncan! Makes you a good person in my books. We don't get kangaroos or wombats here. But we have bats and it's similar. AFAIK it's often the mums with a baby attached that get hit because they drop lower when starting from a tree. If you hit an animal, check on it. https://www.ifaw.org/au/resources/wildlife-rescue-app An app to get the closest wildlife rescue contact.
×
×
  • Create New...