Jump to content
SAU Community

Recommended Posts

Yeah hard to be certain without having checked the configuration but it sounds exactly like the intake air temperature sensor is unplugged, which is an issue if air is based on a MAP sensor not the air flow meters....I would stay off boost if you don't know how it is set up as it is potentially an engine killer

Begs the question what intake air temperature are you running? Because for some models atleast (EG RB26 in an R32) it should be replaced with something less antiquated/faster responding.

  • Inlet Air Temp sensor (IAT) – From factory the GTR is fitted with an IAT sensor to the inlet manifold and this is supported by the G4+ plug-in. However for best results we recommend an alternative IAT sensor to be fitted to the intercooler pipe just prior to the plenum entrance.  This may use the existing IAT wiring or connect to the expansion connector of the ECU.
On 30/11/2022 at 8:20 AM, djr81 said:

Begs the question what intake air temperature are you running? Because for some models atleast (EG RB26 in an R32) it should be replaced with something less antiquated/faster responding.

  • Inlet Air Temp sensor (IAT) – From factory the GTR is fitted with an IAT sensor to the inlet manifold and this is supported by the G4+ plug-in. However for best results we recommend an alternative IAT sensor to be fitted to the intercooler pipe just prior to the plenum entrance.  This may use the existing IAT wiring or connect to the expansion connector of the ECU.

I got the oem inlet temp sensor

On 12/1/2022 at 4:24 AM, The Skyline Guy said:

I got the oem inlet temp sensor

Yeah you can't run that if you're using speed density. It's the exact same part as the coolant temp sensor and is incredibly slow to react. In the OEM ECU all it's used for is to detect heat soak and enrich the mix as a result.

  • 2 weeks later...
On 02/12/2022 at 8:17 PM, joshuaho96 said:

Yeah you can't run that if you're using speed density. It's the exact same part as the coolant temp sensor and is incredibly slow to react. In the OEM ECU all it's used for is to detect heat soak and enrich the mix as a result.

Why do you say that I cant use it when its been fine this whole summer on my new map with link ecu?

You can use it, you just shouldn't as Link state and djr81 posted up for you

On 30/11/2022 at 6:20 PM, djr81 said:

Begs the question what intake air temperature are you running? Because for some models atleast (EG RB26 in an R32) it should be replaced with something less antiquated/faster responding.

  • Inlet Air Temp sensor (IAT) – From factory the GTR is fitted with an IAT sensor to the inlet manifold and this is supported by the G4+ plug-in. However for best results we recommend an alternative IAT sensor to be fitted to the intercooler pipe just prior to the plenum entrance.  This may use the existing IAT wiring or connect to the expansion connector of the ECU.

It is electrically compatible but way too slow to react for proper tuning of quick load changes.

You aren't driving a cheap shitter of a car and an engine rebuild would be a substantial cost. $150 for the correct sensor is good value

  • Like 2
2 hours ago, The Skyline Guy said:

Why do you say that I cant use it when its been fine this whole summer on my new map with link ecu?

If you want the long explanation, you need a fast-reacting IAT because in alpha-N or speed density you want to be able to know roughly the temperature of the air in the cylinder the instant the intake valve closes. This feeds into the ideal gas law equation which is then used to estimate the air mass in grams in the cylinder. The reason why the stock ECU doesn't need to use a fast-reacting IAT is because air mass is not calculated but measured directly at the MAFs. So it doesn't matter what the IAT is downstream, you already know the air mass directly. This applies to any MAF-based system.

  • Like 1

I have researched a bit and came across a this "FAE 33166" https://www.autodoc.co.no/fae/2495306?gshp=1&gclid=Cj0KCQiA4uCcBhDdARIsAH5jyUkvDlPnJalva3nLNelUOFAsjmuzf8U95mQYbH0MUL_tlMm2kDCc6XkaAmHQEALw_wcB

Will this fit in the original location without modification and is it plug and play or do i have to re-tune the car with this new sensor?

1 hour ago, The Skyline Guy said:

I have researched a bit and came across a this "FAE 33166" https://www.autodoc.co.no/fae/2495306?gshp=1&gclid=Cj0KCQiA4uCcBhDdARIsAH5jyUkvDlPnJalva3nLNelUOFAsjmuzf8U95mQYbH0MUL_tlMm2kDCc6XkaAmHQEALw_wcB

Will this fit in the original location without modification and is it plug and play or do i have to re-tune the car with this new sensor?

The thread size is identical but as far as I can tell you will need a harness adapter. Keep in mind part of the reason why people relocate the IAT is that the stock position will heat soak so you will probably want an insulating washer on the IAT at least. Nissan deliberately put the IAT there because the goal of the original sensor was to detect heat soak and enrich the mixture in response.

Also, the "retune" will just be changing the temperature vs voltage calibration table in the tune.

I use the sensor mentioned on the Haltech Elite, they work well. Golebys and Platinum racing also sell them, but they are just the factory long reach metric M12 thread Hella sensor 6PT 009 109 141 or 041 from BMWs and Landrovers, so they are cheaper to buy from a non performance place. They use a 2 pin EV1 connector like the factory injectors.

In the factory location heat soak doesn't seem to be a problem with the Hella sensor as the sensor body is plastic, unlike the factory metal sensor which yeah as mentioned is no good when using VE tuning.

Ok, I had no idea I should change out the iat sensor at all... nor did my tuner mention it. So I should go for the Hella sensor https://www.autodoc.co.no/hella/937856 if I use the oem location? is there any adapters from oem to the hella sensor so i dont have to cut any wires? Can I "tune" in the new sensor myself or should I let my tuner do it?

2 hours ago, The Skyline Guy said:

Ok, I had no idea I should change out the iat sensor at all... nor did my tuner mention it. So I should go for the Hella sensor https://www.autodoc.co.no/hella/937856 if I use the oem location? is there any adapters from oem to the hella sensor so i dont have to cut any wires? Can I "tune" in the new sensor myself or should I let my tuner do it?

You can definitely make an adapter, I just don't know that anyone has one readily available.

18 minutes ago, Dose Pipe Sutututu said:

That's what I did

IMG_20210320_143139_2~2.jpg

47 minutes ago, Dose Pipe Sutututu said:

Looks better than OEM with the boot.

Premium.

Yeah I got my own connector with a straight boot on the blue 32 as most of the kits have a 90 boot, which isn't as nice as the wiring might need to be extended in some cases.

On the white 32 it got the GM sensor from Haltech as it comes with the Elite and because the old man is a tight arse, didn't want to buy another sensor he already had. To fit the GM sensor the plenum needed to be retapped to NPT and about 20mm cut off the temp sensor thread boss, as the GM sensor is much shorter and needs to be pushed further into the airstream.

1276670386_20220826_1832172.thumb.jpg.9a3accecafaa3f8d308e84f338974fae.jpg

 

  • Like 1

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • Brooooo Please send ABS control unit schematic Please! R33 gts25t ABS (Its two plug ecu, black and white) wire colors possible? [email protected]
    • Don't even try to run it on the stock ECU if you're going to have the boost controller bring boost above ~10 psi. I've already told you that. If you use the Nistune ECU, you will need to CAREFULLY read the available documentation for Neo tuning, and read some threads on the Nistune forums, to discover the various things you have to do to prevent the ECU from going bananas when the boost is too high. The is a table associated with th boost sensor that must be modified to prevent it from shitting the bed. This is just one of the things that you will need to do to the tune in Nistune, because the Neo turbo ECU will be expecting to see a number of things (such as the TCS) that are not there, and you have to block the DTCs on those. It is totally not surprising to me that you are having the problems that you are, but the solutions to these problems have been known for >15 years. So just get it done.
    • Hi. Sry iam not a mechanic and iam not at the car atm so i dont know 100% but they told they measure those and even try to change those. AFM they have two. Coils are new a they have my old one too. Plugs too. ECU...we have 25 NEO stock and Nistune 25 NEO.   But i dont know if any one those could be the problem and why/if/what can cause this, Only thing they did not check is fuel...but that walbro 255 is new(like 1,5 years)... That fuel pressure gauge idk...but i let them know Any suggestions?   EDIT: how can they know if it is like you say he ECU pull power when it reaches a specific boost level that is too high? Tha car has boost controler
    • Can you clarify what you mean by boost cut, do you mean it misfires both when under load (driving) and when stationary and out of gear? Or does the ECU pull power when it reaches a specific boost level that is too high (boost control issue)? Does it occur at idle with no throttle? When you say "the ECU is OK", what ECU is it and why do you think it is OK? Have you used the NEO ECU, and if so do you have a MAP sensor attached? Same for the AFM, why do you think it is OK? Do you have any way to put a fuel pressure gauge on it (even just a mechanical one between the fuel filter and fuel rail)?
×
×
  • Create New...