Jump to content
SAU Community

Recommended Posts

Hi All,
Have a VL NA converted to Turbo, after a thicker head gasket, looking into MLS cometic. 
They come in 1.29mm. 1.89mm and above 2.0mm thickness.

Planning to run hi boost (20psi) any advice would be great.


2.5mm thickness would drop it to nearly 8:4:1 or something like that?

Seems like 1.29mm is default choice for rebuilds?

Leaning towards 1.89mm thickness. What thickness do people mostly use?

Will keep it on 98 octane for now but will eventually go on E85

 

TIA.

25 minutes ago, VL_Turbo said:

Anyone?

Really, after just half an hour?

There is no way that I would want an engine with only 8.4:1. What management are you using? Anything with good management for knock control should have no fear of running at least mid 9s.

Update, changing paths and now going with Nitto 1.1mm with (fire rings) head gasket as opposed to mls cometic 1.29mm gasket.

apparently nitto seals better and have stronger fire rings. 
cometic is good but would require copper spray and wet stone/knife sharpening the block as cometic are very sensitive and my leak compression if not done properly. 

👍

  • Like 1

Good luck telling the difference between the two.

 

Also I seriously doubt the nitto gasket is any more forgiving than another mls gasket. They all need to have the sealing surfaces prepped  properly.

Cometic also recommend installing dry. Not sure why you think they need copper spray, or why the nitto can handle a bad deck surface.

 

 

Cometic make great gaskets. Nitto make great gaskets. That's what I mean.

For a slap together build no way is the head gasket going to be the actual root cause of any failure.

 

  • Like 1

*next post- my engine is making a knocking sound

 

Any decent metal head gasket will do the job. Do Arp head studs and valve springs while the head is off.

Pending turbo sizing, fuel system and condition of engine, bottom end will be the biggest weak point.

On 11/3/2023 at 5:45 PM, robbo_rb180 said:

*next post- my engine is making a knocking sound

 

Any decent metal head gasket will do the job. Do Arp head studs and valve springs while the head is off.

Pending turbo sizing, fuel system and condition of engine, bottom end will be the biggest weak point.

Bought some copper spray today. I also believe it's good to add copper spray for extra safety.

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now



  • Similar Content

  • Latest Posts

    • Possibly avoid using a Cometic one unless the deck/head surface are perfectly flat. I did have a look just then and forgiving gaskets such as Tomei or Nitto don't exist for the FJ20, however the Bar-Tek or Kameari ones look good and might do the trick.
    • Because pipe threads for pipe things. M threads for bolt things. Throw some teflon sealant onto it and dust your hands off knowing you did the right thing, instead of going twice around the block to achieve a result using the wrong things. Of course, all of these solutions are ignoring the fact that the minimum thread pitch we're talking about here is 1.25mm, with the 1/4" in NPT or BPS being out around 1.4mm. You will need to know that the boss you're tapping has enough thickness for at least a few threads. That's one of the reasons that 1/8" is commonly used - because the pitch is <1mm. And why would you look to use 1/4" NPT in a BSP country anyway? Ugh.
    • Just throwing around ideas, does it need to be in the compressor cover? Why not the hot side piping?
    • 1/8NPT drill size = 8.7mm. Since the hole got messed up by me, it’s probably around 9mm.    So 1/4” NPT would be next step. A drill size of around 11mm would be preferred there which is not way of my M12 (drill 10.5mm and tap M12 threads) 
    • 3 Kids are starting to hit that ages. I wanted to get them something special to learn on, put down the screens and have some fun. 4Door 2001 R34DE Black Pearl GV1 Jap Import, AU 2nd owner. Pre Work done. Suspension - Wheels Pedders SportsRyder Coilovers   Wheels TSG Spokey Boi 18'x9.5"+15 Body JASI Aero 4 door Type R Full Kit LED Conversion - Parker, Blinkers, & Reverse Exhaust Hurricane Headers 100 CPI high flow cat 2.5" Piping Cannon muffler Internal Bride low max stradia ii - front seats  Bride RO seat base and Rails (R/H) Cube short shifter LED Conversion - Interior   
×
×
  • Create New...