Jump to content
SAU Community

Recommended Posts

I'm going to be buying a JDM from Japan soon and found a potential importer but I noticed on a lot of these JDM cars on the intake manifold and differential there is salt oxidation, which I understand cars over seem to be more prone to rusting than here. Is salt oxidation something to worry about if it's on the frame of the vehicle or is just general rust I should look out for?

Also I heard in Japan they don't have something like we do have here for PPSR or Carfax from America, but a guy told me they do they do have it, what's the best website to do the check if it exists?

On 5/13/2023 at 10:34 PM, silviaz said:

I'm going to be buying a JDM from Japan soon and found a potential importer but I noticed on a lot of these JDM cars on the intake manifold and differential there is salt oxidation, which I understand cars over seem to be more prone to rusting than here. Is salt oxidation something to worry about if it's on the frame of the vehicle or is just general rust I should look out for?

Also I heard in Japan they don't have something like we do have here for PPSR or Carfax from America, but a guy told me they do they do have it, what's the best website to do the check if it exists?

CarVX is the nearest equivalent to Carfax in the US. White rust on aluminum parts like an intake manifold usually also means there is rust elsewhere on the chassis.

  • Like 1
5 hours ago, joshuaho96 said:

CarVX is the nearest equivalent to Carfax in the US. White rust on aluminum parts like an intake manifold usually also means there is rust elsewhere on the chassis.

Thanks man, I'll use that. This is the oxidation I was mentioning, is that technically rust? Seems like there is some yellow bubbling to.

12.JPG

The pic isn't great, but I think it is the exhaust heat shield with surface rust. That is perfectly normal, it is not painted because it is too close to the exhaust for paint to survive

  • Like 1
On 16/05/2023 at 12:59 PM, silviaz said:

Thanks man, I'll use that. This is the oxidation I was mentioning, is that technically rust? Seems like there is some yellow bubbling to.

12.JPG

it's not technically rust, but it will deteriorate the shield over time. the chloride pits the metal over time. if it gets too manky you can just replace it. you can't paint it cos it gets too hot.

  • Like 1
31 minutes ago, funkymonkey said:

it's not technically rust, but it will deteriorate the shield over time. the chloride pits the metal over time. if it gets too manky you can just replace it. you can't paint it cos it gets too hot.

Oh I was referring to the white metal thing at the back looks like the differential.

1 hour ago, Duncan said:

The pic isn't great, but I think it is the exhaust heat shield with surface rust. That is perfectly normal, it is not painted because it is too close to the exhaust for paint to survive

I meant this part not the exhaust shield.

34.JPG

Yes, so that's definitely the diff cover and they will all inevitably have white oxidation on them after a few years. There can be no expectation of raw cast alloy retaining any sort of nice as cast finish on an exposed part anywhere on a car.

The question is ....is it just the usual light coating of white oxide, or is it horribly consumed and covered in little encrustations of chlorides? If the former, then the oxidation state of the alloy parts is not really any guide to how rusty the steel parts might be. But if it is horribly messed up, then the car might have spent a lot of time driving through wet slushy snow and salt, and it might have corrosion issues. The only way to know if to have a decent look.

R33s and 34s in particular have a lot of problems around the front suspension towers. R32s less so there, but they can all suffer all over the place from salt. They should have all been rescued from Japan within 5 years of being built. Anything coming out of Japan now would want to have been stored in a garage or warehouse for the last 15 years.

  • Like 1
1 hour ago, GTSBoy said:

Yes, so that's definitely the diff cover and they will all inevitably have white oxidation on them after a few years. There can be no expectation of raw cast alloy retaining any sort of nice as cast finish on an exposed part anywhere on a car.

The question is ....is it just the usual light coating of white oxide, or is it horribly consumed and covered in little encrustations of chlorides? If the former, then the oxidation state of the alloy parts is not really any guide to how rusty the steel parts might be. But if it is horribly messed up, then the car might have spent a lot of time driving through wet slushy snow and salt, and it might have corrosion issues. The only way to know if to have a decent look.

R33s and 34s in particular have a lot of problems around the front suspension towers. R32s less so there, but they can all suffer all over the place from salt. They should have all been rescued from Japan within 5 years of being built. Anything coming out of Japan now would want to have been stored in a garage or warehouse for the last 15 years.

Ah ok makes sense, will cost be a fair bit to inspect so hopefully turns out right.

Yeah the oxidation is usually a result of a car driving through and sitting in salted roads. Which is common in Japanese high country. Super high chance if the chlorine oxide has formed that the iron/steel parts are rotted too. Get a thorough underbody check done and look out for tell tale cover up spray paint too.

3 hours ago, funkymonkey said:

Yeah the oxidation is usually a result of a car driving through and sitting in salted roads. Which is common in Japanese high country. Super high chance if the chlorine oxide has formed that the iron/steel parts are rotted too. Get a thorough underbody check done and look out for tell tale cover up spray paint too.

Makes sense. Yeah will defs get a check, seems to be priced quite a bit less compared to others.

  • Like 1

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • Must have been an absolute nightmare to drive when the power steer was out, the rack ratio/wheel size/caster is all set up for power assistance
    • Welcome to SAU, what are you looking at buying?
    • I checked the injectors again (1 and 2, since they’re easiest to access) to make sure they weren’t clogged. Even though the entire fuel system had been cleaned, I wanted to be certain. Everything looked clean, so I reinstalled and connected everything. When I started the car to confirm everything was okay, it immediately revved up high, so I shut it off straight away. I checked to see if I’d missed a vacuum hose or something, but everything was connected. On the second attempt, the car ran without the high idle, but I noticed a distinct “compressed air” sound coming from the engine bay. Tracing the sound, I pushed injector #6 forward slightly and the noise stopped — it turned out it wasn’t seated properly, despite the fuel rail being bolted down. While holding it in place, the car idled steadily without stalling and ran for over 5 minutes. At this point, I pulled all six injectors out just in case I hadn’t seated them correctly or dirt had gotten onto the O-rings. Unfortunately, I discovered that I had damaged 3 out of 6 injectors (the OEM 270cc ones) during installation. So yes, this was my fault. Since only the pintle caps were damaged, I’ve ordered a Fuel Injector Service Kit from NZEFI to refurbish them. In the meantime, I reinstalled my new injectors – the car now idles fine for over 15 minutes without stalling. I have not attempted to drive it so far. It’s not perfect yet, as it hesitates when the throttle is pressed, but it’s a big improvement. Unplugging the IACV with the new injectors idles at around 800rpm, even with the IACV screw tightened fully. But this is probably due to tune.
    • I wanted to try and preserve the front bumper as long as possible, they're not cheap and are made to order in Japan. Taking inspiration from my previous K11 Micra build where I made an undertray for the Impul bumper, I did the same for this BN Sports bumper but a little slimmed down.  This time round I only made a 'skid plate' (if that's the correct wording/term) for just the bumper surface area, the Micra version covered the gap like an undertray. Starting off with a sheet of mild steel approx. 0.9mm thick 4ft x 2ft in size. I traced around the bumper, cut it out and cleaned the edges. Luckily I was able to get two halves from one piece of metal In the video I installed it as is, but I've since then I've removed it to spray and add a rubber edging trim. The rubber trim is suitable for 1-2mm and it's a really nice tight fit. The bolts had to be loosened due to the plates being too tight against the bumper, the trim wouldn't push on I used some stainless M6 flat headed bolts for a flusher finish (rather than hex heads poking down), I believe this style fastener is used for furniture too incase you struggle to source some. The corner's are a little wider, but this may be an advantage incase I get close to bumping it  The front grill got some attention, finally getting round to repairing it. Upon removal one fixing pulled itself out of the plastic frame, one side is M8 that fixes inside of the frame, where as the other side is M5. Not knowing I could get replacements, I cut down an M8 bolt, threaded it inside the frame along with a decent amount of JB Weld.  The mesh was replaced to match the bumper. One hole on the bonnet/hood had to be drilled out to 8mm to accommodate the new stud, once the glue had set it could be refitted. I think the reason the grill was double meshed was to hide the horn/bonnet latch (which makes sense) but I much prefer it matching the bumper Bumper refitted and it's looking much better IMO The Youtube video can be seen here: https://www.youtube.com/watch?v=bVZP35io9MA
    • The video for the servicing and fuel filter change can be seen here: https://www.youtube.com/watch?v=uLJ65pmQt44 One of the main jobs I wanted to do before the car officially went on the road, was to remove the awful looking blue silicone hoses. There's nothing wrong with having coloured silicone hoses, but I realise as I'm getting older I prefer monotone engine bays with a splash of colour on the engine cover(s). I cover this in a lot more detail in the Youtube video, so unfortunately there's limited photos of the process. The intercooler, upper radiator, boost vacuum and upper breather hoses were all changed to black silicone with mikalor clamps. The only blue left is a blanking cap at the back of the inlet manifold and the GReddy pulleys (which will be replaced for stock when the cambelt gets replaced) While the intercooler pipes were off I gave them a quick clean/polish too A before photo I do have a replacement air filter on its way. Fuse box covers were painted blue, they're now satin black Another job on the list while the bumper was off, is to add some mesh https://live.staticflickr.com/65535/54737966256_99b28bfa30_c.jpg[/img] I was hoping to use some thin wire to secure it, but it seems I've misplaced it and the wire I had was too thick to twist easily. I ended up using cable ties for the time being https://live.staticflickr.com/65535/54737131882_c2b7989dcc_c.jpg[/img] Was pleasant to see this https://live.staticflickr.com/65535/54737131627_8b2aab13b3_c.jpg[/img] The last thing to do was to fix the front grill and re-mesh that to match but I ran out of time The Youtube video can be seen here: https://www.youtube.com/watch?v=R4FsF6tgizE&t=23s
×
×
  • Create New...