Jump to content
SAU Community

Recommended Posts

Hey all, on my Subaru I noticed I have a whistling sound when from 60km an hour onwards, below that I don't hear it. I used to hear it from 80km onwards but now it's 60km. It does seem to get louder then plateau's, I thought maybe it's the wheel bearings but I got them replaced about 70,000km ago, unless the mechanic put cheap ones on. What would you guys lean towards it being? Also when going over small bumps and especially when I'm turning the wheel on bumps I can hear like a twitching sound I think from the rear passenger side, maybe the strut? 

I know the rear of the car itself has been squeaky probably since I bought it (separate issue), but I've never fixed it as I generally don't have people sitting in the back and it's not overly noticeable unless I go over bumps with people in the back or if I'm driving myself but turn into a carpark ramp to go up the parking.

On 11/07/2023 at 10:35 PM, GTSBoy said:

You seriously want us to attempt to diagnose odd sounds over the internet?

To be fair something like every second engine issue thread starts with a recording of odd noises happening in the engine bay, no? In that sense I'd say having a recording would be good for a start.

44 minutes ago, soviet_merlin said:

To be fair something like every second engine issue thread starts with a recording of odd noises happening in the engine bay, no? In that sense I'd say having a recording would be good for a start.

Yeah, but when it's happening at 60+ km/h, good luck trying to get a recording that we can hear anything over the wind roar.

On 11/07/2023 at 9:34 PM, silviaz said:

I thought maybe it's the wheel bearings but I got them replaced about 70,000km ago,

Could still be wheel bearings. Or a diff? Dunno if that's a whistle, probably more a whir.

Sounds like the rear is unrelated? Hard to diagnose anything with the amount of info though. YOu could get under the back and just check everything is tight ?

5 hours ago, PranK said:

Could still be wheel bearings. Or a diff? Dunno if that's a whistle, probably more a whir.

Sounds like the rear is unrelated? Hard to diagnose anything with the amount of info though. YOu could get under the back and just check everything is tight ?

Bearings got replaced (could have been cheap ones, though I am leaning towards it), will get it checked out one of these days. Doubt it's the diff, can't hear it on passenger side only driver side.

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • Don't be ridiculous. "2-3 ugga duggas or one Oof. You have to use Oof on tie rods because you can't get an ugga dugga on there." Is not helping the guy at all.
    • I have done a lot of research before posting here and on gtruk forum. couldn't find anything. I have my gauges all part except the needle itself. the needle has a extremely small hole in the center, but the shaft going to the needle is extremely small and appears to have nothing to index it either. doesn't seem strong enough to simple pry or pull without damaging something. Already tried the old spoon trick on a extra triple meter I have from a gtt, but no luck. the center cap comes off easily but the hole in the meter face plate aren't big enough to get over the needle itself. figured this would be my best place to find someone who might have actually removed theirs. wonder if there is some type of small pin press tool to push the pin in while pulling the needle base off.
    • Ok...its taking me long enough to finally do this.  Feck financial security...heart disease will get me soon enough anyway So welcome to the garage..."Clem" Belsil80 has been running a 370Z in Super TT series. So after entering with him in last years Winton 300 i figured I  need my own car. Seems SAU Vic race cars need to be yellow....{tick} Reckon with enough motor i will be able to make up for the lack of talent and stay ahead of the 370Z... but the LS powered S13 and E36s are a ways up the road Aim is to have a car that doesnt stop or turn but has a bit of shed built motor with jam...maybe some cream  First step is getting this ex drift car log booked I am keeping faithful silver car. As the road-club car gets upgrades the race car wil get the sloppy seconds
    • Assuming that they will come off without damage at all.... i would have thought just pull straight up off the spindle with a something or other than can reach underneath. Have you searched for youtube vids of people doing similar on R34s or any other Nissan from the same vintage? They should be the same technique, in all likelihhood.
    • Keeping in mind that sandblasting is really aggressive on softer metals like cast alloy, and you can do damage that you might regret. For trash wheels, not a problem. For wheels with value/scarcity issues, etc.... perhaps a less aggressive media is a better choice?
×
×
  • Create New...