Jump to content
SAU Community

Recommended Posts

Howdy friends,

I found a few posts on 3D printing but thought I might start a thread to consolidate the bits and pieces I make for the my R32 Skyline and update the original post as I go.

I only recently got into this hobby and for some of those obscure parts which are difficult to locate part numbers, or are no longer in production, the 3D printer is a pretty useful resource, albeit there will always be some cosmetic limitations.

I'll list model files on my Printables account for those with their own printers so you can download and print at your leisure.

If anybody has any ideas on parts they can't locate and want me to have a crack at making something, feel free to post below and I might be able to help out 🙂

Cheers,

Sean

  • Like 2
Link to comment
https://www.sau.com.au/forums/topic/485352-3d-printing-fun/
Share on other sites

  • 1 month later...

Howdy friends,

So this evening I had a need to remove the rear compressor turbo pipe (long story, but I'm replacing it due to a bolt snapping off in the pipe and managing to then snap an extraction bit in the broken bolt, fun times -_-). The rear bolt is a bit of a bastard and very little room to get good leverage. I was able to get a 12 mm socket onto the bolt head, but none of my ratchets were able to fit, so I put together a "stubby" socket wrench to get it out and it worked surprisingly well 🙂. In the past I've "made" tools by cutting down spanners and bending them with a torch etc, but this 3D printed wrench was way less effort.

I'll be keeping this one in my "special tool draw" from now on for sure ^_^b

https://www.printables.com/model/868973-half-inch-stubby-socket-wrench

image.thumb.png.6d102a91082ebe1baeef73fa48226c90.png

StubbyWrench.thumb.PNG.eee7396733b1bb24f11d896aeaddbb84.PNG

PipeReplacement.thumb.PNG.e28aa7b46e6409c1865e365bb340d5ca.PNG

  • Like 2
Link to comment
https://www.sau.com.au/forums/topic/485352-3d-printing-fun/#findComment-7989529
Share on other sites

Plastique? So there will be a limit to how much torque you can apply. I guess the short length probably plays well with that. You chose the length based on the room you had available to swing it in?

I've made something similar with round bar, heated up and bent sharply, then a little spray with the MIG to fill out the corners of the 3/8" square and some filing to shape. I've also seen it done just using a short length of 3/8" square bar (or there are double ended male 3/8" socket accessories which can do the same thing) and a bit of plate with a 3/8" square hole broached through it to use as a handle that you can slip over the square drive.

You could probably do the job you had to do with a 12mm box spanner too. You know, the sort that you get for spark plugs on whipper snippers etc. Box spanners are beneath scorn most of the time, until one saves the day.

Link to comment
https://www.sau.com.au/forums/topic/485352-3d-printing-fun/#findComment-7989639
Share on other sites

On 09/05/2024 at 2:26 PM, GTSBoy said:

Plastique? So there will be a limit to how much torque you can apply. I guess the short length probably plays well with that. You chose the length based on the room you had available to swing it in?

I've made something similar with round bar, heated up and bent sharply, then a little spray with the MIG to fill out the corners of the 3/8" square and some filing to shape. I've also seen it done just using a short length of 3/8" square bar (or there are double ended male 3/8" socket accessories which can do the same thing) and a bit of plate with a 3/8" square hole broached through it to use as a handle that you can slip over the square drive.

You could probably do the job you had to do with a 12mm box spanner too. You know, the sort that you get for spark plugs on whipper snippers etc. Box spanners are beneath scorn most of the time, until one saves the day.

Yep PETG (Polyethylene terephthalate glycol), my 'go to' plastic, printed to precisely how long I wanted 🙂, about a finger length ha ha.

I would usually grind up something but since I've got the printer I thought I might give it a try and it worked beautifully ^_^b

So with regards to torque, there's a little bit of science behind the orientation of the print, fill density, fill pattern and number of external perimeters which can increase the strength dramatically, but you still need to work within the constraints of the material and the orientation of the model for sure. I certainly wouldn't be making a breaker bar out of plastic, but this little bugger is very strong for it's size that's for sure.

Link to comment
https://www.sau.com.au/forums/topic/485352-3d-printing-fun/#findComment-7989742
Share on other sites

  • 5 weeks later...

Howdy all,

A mate of mine picked up an R32 GTS-T recently and it had a very... colourful... gear knob that needed to be replaced immediately 🤣

I put together a replacement which is reminiscent of the Nismo offering, which I also really like both the feeling and design. I basically took what they did and optimising for 3D printing, with the exception of the top chamfer, where I prefer a filleted design, despite it not printing quite as clean.

If anybody needs another thread size for the locker or if you prefer a top chamfer similar to the Nismo one, I'm happy to put something together for you and as a side note, I was really impressed by the TPU lock nuts. Originally I was going to use steel and then found out the ones I had on hand were sadly M10 1.5 pitch, rather than the required M10 1.25 pitch, so I had to get a bit creative rather than wait for the bolt shop to open.

In the picture it looks a little bit 'rough' at the top due to the layering printing on a curve, but in reality it's not very noticeable at all and honestly feels pretty good in the hand.

https://www.printables.com/model/910138-nissan-skyline-r32-gear-knob

Regards,

Sean

  • Like 2
Link to comment
https://www.sau.com.au/forums/topic/485352-3d-printing-fun/#findComment-7990458
Share on other sites

  • 7 months later...

Howdy friends,

So another weird one today, I was looking into replacing some broken clips holding the front grille for the R32 GTR (part number 01553-03831), and noticed the brackets which are supposed to hold the grille in place were also missing 😑. I do recall seeing this issue many years ago, but didn't fix it at the time.

A quick look on eBay and I was able to find the genuine brackets, along with all the screws which suited the headlights (part numbers 26042-08U05,26092-08U05). Happy days!.... 

Once they arrived however there was an extra nut in the packaging which implied that there should also be a bolt or a stud, and sure enough, after a bit of searching I found this thread from 2013, and @Ants clearly shows a stud should be present. Reading around a bit more, it's possible the headlights on my car are the "povo pack" headlights as mentioned by @funkymonkey in this thread way back in 2008. This could explain why the studs are missing on my set of headlights.

Looking at the headlight diagram I wasn't able to see a suitable part number for the stud itself. The headlight did indeed have a recess that looked like it would accept a stud, but interestingly no thread or anything obvious how the stud would be affixed to the headlight, I suspect it may have been glued in, press fit, or melted into the plastic at the factory. Another member may be able to clarify if they happen to have a genuine set of N1 headlamps. The only thing we have to work with within the recess is a keyway which likely is there to prevent the stud from rotating within the recess.

26042-08U0526092-08U05.thumb.PNG.2fbd8c765fa2c0972be4330dc124c5a1.PNG

In any case, back to 3D printing, I put together a model which acts like a pug with a friction fit inside this recess, making use of the keyway so it doesn't rotate while tightening a bolt. Printing in TPU will allow it to slightly swell making a nice snug fit without cracking the part. I've designed the adaptor it to accept an 20 mm M6 bolt (stainless with a cap head in my case), as opposed to the standard M5 stud and I made use of the standard galvanised split washer that came with the genuine brackets from Nissan.

Once the bolt and screws were all in place, giving the bracket a gentle shake gave the classic "shaking the car" feeling, very solid, which gives me confidence this is going to be able to hold on much better than the janky solution which seems to have been here for the past decade or so. Overall I'm really pleased with how this turned out and maybe there are more people out there running these headlights without a centre stud at all!

Link to the freely available model on Printables: Click here

Regards,

Sean

Studadaptor.thumb.PNG.6f329badf5bb0f86c7702083d718aed9.PNG

Studadaptorinsertedintoblindholewithkeyway.thumb.PNG.6274b208d8b69cee7a235ecd1068def1.PNG

Boltinsertedintobracketwithsplitwasher.thumb.PNG.69c5b0b4cc1dc6e348108fd6e8887ce9.PNG

Standardscrewsinserted.thumb.PNG.36f759775530e11b71ceb1dd7a5e57bf.PNG

GenuineNissanBrackets.thumb.PNG.43c416403521565cb27c7274620e126d.PNG

GenuineNissanBrackets2.thumb.PNG.f8dacf9828157acbf06ef7e20acfeae9.PNG

 

Stud adaptor inserted into blind hole with keyway2.PNG

  • Like 1
Link to comment
https://www.sau.com.au/forums/topic/485352-3d-printing-fun/#findComment-7996805
Share on other sites

Thanks for sharing this, and BTW if your headlights are in good condition they are worth thousands....you might want to consider replacing them with brand new LED ones like this (https://www.nengun.com/78works/full-led-headlights-r32-skyline) and making enough profit to buy a house in Sydney

  • Like 2
Link to comment
https://www.sau.com.au/forums/topic/485352-3d-printing-fun/#findComment-7996807
Share on other sites

No worries at all 🫡

I think the most satisfying things to make are the little bits that are just impossible to find or they're no longer manufactured. Generally I always try to replace parts with OEM wherever possible.

This little project is also great because it'll never see the light of day, but strengthen these brackets so it's not just relying on the little standard screws in the headlight plastic.

As soon as I saw the standard brackets and screws I thought, "well I'm not going to install with just the screws, the plastic tabs will just snap off". It's crazy how expensive everything has become yeah. But I suppose that's supply and demand; granted it's a lot easier to get brand new genuine parts these days which is fantastic 😊, I don't have to get totally reamed at the local Nissan dealer ha ha

We sure are lucky we have all these manufacturers making parts these days, a few really great Australian companies too like Platinum Racing Products and Fit Mint Automotive, what a time to be alive ❤️ . I've got my eye on the RB26 head by PRP as mine has a very fine hairline crack, so that'll need to be addressed some time in the future.

If you have any requests or odd things to make feel free to let me know and I can have a crack at making replacement parts ✌️

Link to comment
https://www.sau.com.au/forums/topic/485352-3d-printing-fun/#findComment-7996808
Share on other sites

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • Not too sure just yet, want to have a go at doing what I can myself, but to start with want someone to cast their eye over it tell me what needs doing to get it running and back on the road, so anyone with great overall knowledge would be ideal.
    • I personally would go with cutting out the rubber. Then deal with getting sleeve off separately. Rubber can be painful to cut, it loves to jam up cutting tools. I normally have success with drill bits, deburr bits, angle grinders, jigsaw, reciprocating saw, and never forget... fire. Obviously different tools won't work in all locations you're trying to work with, and you need to be comfortable with each. You personally may be happy slowly slicing it out with a razor blade, if you are, go for it with one too! Feel free to wait for others to weigh in also on their thoughts.
    • So ... I got everything disconnected and started dropping the frame. Three of the four mounts started to come down but the fourth one (the one with the nut that gave me all the trouble) won't budge. The inner metal sleeve stays up tight against the chassis rail although the outer part of the mount drops a bit (and can be levered quite a lot more) but it's just stretching the rubber bushing. So I reckon there's some serious corrosion inside the inner sleeve and holding it tight to the lug at the top of the bolt. Tried everything I can think of so far: penetrating oil, whacking the top of the sleeve to vibrate it and wedge a screwdriver blade in there. I also tried to turn the inner sleeve a bit by hitting it with a chisel at the bottom. It's stuck solid. What do you think about cutting the rubber with a blade so I can drop the subframe around it anyway. Then worry about getting the inner sleeve off after? Will that work? Is it gonna give me even more problems?
    • Steam valve seals are usually responsible for cold start smoke, it goes away once engine warmed up. Disconnect it let engine breathers and let it breath freely, see if problem goes away after a short drive. Also check to make sure engine oil drain pipe is not blocked or kinked. 
    • Haha thanks! Yea I'm moving over from 2x 1000cc jets pre throttle over to 6x 190cc direct port jets and 1x 500cc pre throttle jet.  Direct port comes with all the advantages you would expect, except that pre throttle does cool down IAT'S more. That's why my direct port nozzle placement is closest to the plenum as possible in the runners to allow the air more time to cool before being sucked in. I'm also putting that one 500cc pre throttle jet to help with more cooling. It's a hybrid system. There's a lot more advantages to moving over to a PWM solenoid with a constant pressure system vs my old PWM pump setup, but I'll get more into that once I'm done converting everything over. The ricer in me is excited to see SS tubing all over my manifold though!
×
×
  • Create New...