Jump to content
SAU Community

Recommended Posts

Apologies, but not willing to hunt through 21 pages of "Stagea Parts List".

I have a RB25DET from a (early, 1996?) C34 in my R32 GTS4, and I need a new Rocker Gasket Kit, including the washers.On the assumption that all 25s are the same, I got a Protorque GVC6100 kit, but it has the wrong style washers, and the gasket appears to be a bee's-dick short. Most kits don't clearly show the washers, so I don't know if they will work. I've found a Durapro GSRC3025K, but again not confident it has the correct washers (washers need to be basically flat, not the type that insert into the rocker).

I contacted my local Nissan dealer, asking if they could get the correct kit if I gave them the engine number. The can only search on a VIN.

There are kits on eBay, but they claim to fit 180SXs as well as Stageas / R33s / etc, so I'm dubious that they are the correct kit.

Anyone done this before? Maybe give me your VIN so I can quote it to the dealer.

Any help / guidance appreciated.

Link to comment
https://www.sau.com.au/forums/topic/485403-rocker-gasket-kit/
Share on other sites

Being a 96 it would be a non neo rb25, so any non neo rb25 gasket should fit. If I was you, I'd be calling the likes of kudos motorsport , EFI solutions to ensure you're getting the right part and ordering a genuine Nissan gasket kit. Will be a lot cheaper than Nissan spare parts as well.

As  I said in OP, the grommets (washers) are different. I need the plain flat type that acts like a washer - the kit I originally got has the type that insert into the retaining bolt hole.

I'll give kudos a call Monday, see what they can do.

This is NOT the type I need:

genuine-nissan-cam-rocker-cover-bolt-seals-5pce-bag-fits-ca18-rb20-rb25-rb26-rb30-513_600x.thumb.webp.a52c651b103f2c7252e771d0b0536463.webp

That is the correct type on my stagea's rb25; they pull down about 50% in height as you tighten them, and the bonded metal part is the washer (ie, your pic is upside down)

Per this post, those are the ones I used on mine 

 

This is how they sit, don't overtighten them

20240407_105901.jpg

(upside down because that's how they were pictured!)

Aha! So it IS the type I need!

Actually found replacement bolts that come with a flat rubber washer from EFI Solutions (https://www.efisolutions.com.au/billet-rocker-cover-washer-retainer-kit-rb20-rb25 ) - might fancy-up the rocker covers with a set.

image.thumb.jpeg.463f9a93e9cba7d40924335827d4c7d5.jpeg

Edited by blind_elk

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • As far as I can tell I have everything properly set in the Haltech software for engine size, injector data, all sensors seem to be reporting proper numbers.  If I change any injector details it doesnt run right.    Changing the base map is having the biggest change in response, im not sure how people are saying it doesnt really matter.  I'm guessing under normal conditions the ECU is able to self adjust and keep everything smooth.   Right now my best performance is happening by lowering the base map just enough to where the ECU us doing short term cut of about 45% to reach the target Lambda of 14.7.  That way when I start putting load on it still has high enough fuel map to not be so lean.  After 2500 rpm I raised the base map to what would be really rich at no load, but still helps with the lean spots on load.  I figure I don't have much reason to be above 2500rpm with no load.  When watching other videos it seems their target is reached much faster than mine.  Mine takes forever to adjust and reach the target. My next few days will be spent making sure timing is good, it was running fine before doing the ECU and DBW swap, but want to verify.  I'll also probably swap in the new injectors I bought as well as a walbro 255 pump.  
    • It would be different if the sealant hadn't started to peel up with gaps in the glue about ~6cm and bigger in some areas. I would much prefer not having to do the work take them off the car . However, the filler the owner put in the roof rack mount cavities has shrunk and begun to crack on the rail delete panels. I cant trust that to hold off moisture ingress especially where I live. Not only that but I have faded paint on as well as on either side of these panels, so they would need to come off to give the roofline a proper respray. My goal is to get in there and put a healthy amount of epoxy instead of panel filler/bog and potentially skin with carbon fiber. I have 2 spare rolls from an old motorcycle fairing project from a few years back and I think it'd be a nice touch on a black stag.  I've seen some threads where people replace their roof rack delete with a welded in sheet metal part. But has anyone re-worked the roof rails themselves? It seems like there is a lot of volume there to add in some threads and maybe a keyway for a quick(er) release roof rack system. Not afraid to mill something out if I have to. It would be cool to have a cross bar only setup. That way I can keep the sleek roofline that would accept a couple bolts to gain back that extra utility  3D print some snazzy covers to hide the threaded section to be thorough and keep things covered when not using the rack. 
    • Probably not. A workshop grade scantool is my go to for proper Consult interrogation. Any workshop grade tool should do it. Just go to a workshop.
    • In my head it does make sense to be a fuel problem since that is what I touched when cleaning the system. When I was testing with the fuel pressure gauge, the pressure was constantly 2.5 bar with the FPR vacuum removed. When stalling, the pressure was going up to 3.0 bar (which is how it should be on ignition).
    • ECUtalk pages don't mention they support the ABS computer (consult port has more than one CAN), so you might just need a different scan tool. But, I would expect ABS is a different light to the brake warning/handbrake light, do you see an ABS light come on for a few seconds when you turn the key from ACC to IGN? But since you said: I'd have a look at the ABS sensors in the rear hubs to make sure they are not damaged, disconnected etc.
×
×
  • Create New...