Jump to content
SAU Community

Fixing exhaust position?

PranK

By PranK,
in General Maintenance

 Share

Recommended Posts

PranK Grand Master

PranK

Posted
Posted

I bought an off-the-shelf exhaust for my car late last year and I've had it on and off about 4 times trying to get it to sit right. 

The middle slip-on part does not go all the way on and its causing the rear to be pushed back, protruding a lot. The rear hangers all sit below and to the back rather than just directly below. Also, I've had to add bigger (longer) mounts at the back as the exhaust hits the bumper after a short drive and it heating up. 

What sucks is, the first time I put it on it looked the best, each subsequent time got worse 🤣! 

This was a cheap exhaust (duh) and the shop has been less than exceptional with support but at the end of the day I do like it and it sounds great so I'd like to keep it but just get it fixed.

Exhaust shops are not that common any more. Anybody know any place on the north of Sydney? I guess I can just check in at a few places near me, most are for 4wd's and lifting though! 😆

I was considering modifying it myself, but the angles scare me.

PXL_20250105_073246351.MP.jpg PXL_20250105_073236357.jpg

Link to comment
https://www.sau.com.au/forums/topic/486039-fixing-exhaust-position/
Share on other sites
PranK Grand Master

PranK

Posted
  • Author
Posted
12 hours ago, Milkmun said:

Protrusion looks pretty good there.

 

11 hours ago, Kinkstaah said:

Yea - Needs a side shot TBH. Other than that, actually looks pretty good. My OCD would want to see it tuck 'higher' but melty melty is a concern.

Oh really? Maybe I'm being silly. I'll get some more shots. I had it higher but found that it went too high after a drive, I never knew this but exhausts can move around a bit when hot (makes sense, just never knew) and when it was higher it would make nice cooking plastic smells. That said, I could put some heat tape on a'la 90's R33 exhausts :D 

 

1 hour ago, Duncan said:

Not sure how broadly you define Northside :) but Castle Hill Exhaust are still around and could sort it.

Ha, I've spent a lot of my life in castle hill waiting for cars to be done. I think I'd prefer something closer but thanks D. 

Kinkstaah Grand Master

Kinkstaah

Posted
Posted

I'd want an even MORE side on view. More or less you want to make sure the outlet is actually square with the outermost part of the bumper. Or you end up getting soot all over your bumper from your hektik exhaust. In any case, it looks pretty close.

I think the way to fix this is probably more of an overhaul at an exhaust specialty shop if you want tips that are rounded off or sit nicely with the bumper but have proper clearance and don't move - Probably more of a redesign than a quick fix. I've pencilled in my own exhaust with its own various problems, pinholes, PITA fitment, and other issues and can see myself going to a shop and saying "JUST DO THIS BUT BETTER?" 

Which is gonna work better than any more small fixes. I'm gonna chime in here officially with "from an outsider perspective this exhaust looks fine so this is self OCD probably" (which I also suffer from)

  • Like 1
PranK Grand Master

PranK

Posted
  • Author
Posted

Love your work guys, I think I'll leave it then. I was a bit self conscious about how it looks but you've convinced me its fine. 

@GTSBoy I'll just rip down a chain link fence and cram the pipes into my tips. There's tonnes of room. We can call it BozoEuro. 

The Bogan Grand Master

The Bogan

Posted
Posted

Tips look fine to me......but

Boring stuff: Legalities - Vehicle standards notes that exhausts cannot extend to a point where they could cause injury

Scary stuff: Mrs cuts open her shin putting stuff in the boot (ensure you have some bandaids and shiny jewellery handy)

GTSBoy Grand Master

GTSBoy

Posted
Posted
13 minutes ago, The Bogan said:

Tips look fine to me......but

Boring stuff: Legalities - Vehicle standards notes that exhausts cannot extend to a point where they could cause injury

Scary stuff: Mrs cuts open her shin putting stuff in the boot (ensure you have some bandaids and shiny jewellery handy)

Easy solution to both of those. Put a split bit of garden hose on each one. Attractive and practical!

  • Haha 2
PranK Grand Master

PranK

Posted
  • Author
Posted
28 minutes ago, The Bogan said:

Tips look fine to me......but

Boring stuff: Legalities - Vehicle standards notes that exhausts cannot extend to a point where they could cause injury

Scary stuff: Mrs cuts open her shin putting stuff in the boot (ensure you have some bandaids and shiny jewellery handy)

I once hit my knee on an exhaust on my sisters Suzuki Sierra after she drove it her *normal* way. My knee looked like porridge for weeks.

Bec and my daughters never go near this car. I can see one of my dogs losing an ear though. 🤔

  • Haha 1
PLYNX Mentor

PLYNX

Posted
Posted
On 1/8/2025 at 10:32 AM, PranK said:

I once hit my knee on an exhaust on my sisters Suzuki Sierra after she drove it her *normal* way. My knee looked like porridge for weeks.

Bec and my daughters never go near this car. I can see one of my dogs losing an ear though. 🤔

Wait ! What  ? My knees are NOT supposed to look like porridge ? ? 

Ummmm ! I'd best get to the docs ! 

Maybe there a cream or antibiotics or something! !

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now
 Share
Go to topic listing


  • Similar Content

  • Latest Posts

    • MBS206
      Duncan's V37.......race car?

      By MBS206 · Posted

      Even more fun, leave all the ADAS stuff plugged in, but in different locations, hopefully avoid any codes!   And honestly, all these new cars with their weird electronics. Pull all the electronics out Duncan, and just shove an aftermarket ECU and if needed a trans controller in, along with a PDM. Make it run basic but race car styled!
    • Duncan
      Duncan's V37.......race car?

      By Duncan · Posted

      To follow up a question from earlier too since I had the front bar off again (fking!) This is what is between the bumper and the drivers side wheel And this is the navigator side, only one thing but its a biggy! So basically....no putting coolers in the wheel arches without a lot of moving other stuff. Assuming I move to properly race prepping this car I'll take that job on and see how the computers respond to removing a whole bunch of ADAS modules
    • Duncan
      Duncan's V37.......race car?

      By Duncan · Posted

      So I prepped the car for another track day on Wednesday (will be interesting to see coolant temps post flushing out and the larger reservoir, with a forecast of 3-14 being 20o cooler than last time I took it out). Couple of things to mention; since I am just driving the car and not taking a support vehicle, I took the rear seats out and just loaded the back up Team Trackday style. Look at all that space! To cover off removing the rear seat....it is weird (note the hybrid is probably different because it wouldn't have folding rear seats) Basically, you remove the lower seat base, very similar to a r series but it is a clip that pulls forward to release the base rather than it being bolted down. Easy Then, you need to remove the side section of the rear seat on each side. There is a 14mm head nut at the bottom of the side piece, the it slides upwards off a hook at the top to release; you also need to unhook the seatbelt from the loop at the top. Then the centre piece is weird. You need to release/fold the seats forward with the tab in the boot on each side From there, there are 2,x12mm headed bolts holding the rear of each seat to the folding bracket, under the trim between the rear seat and the boot (4x christmas tree clips there, they suck). The seat is out but you can see where the bolts attach to the bracket
    • RP1421
      S15 Spec R

      By RP1421 · Posted

      As discussed in the previous post, the bushes in the 110 needed replacing. I took this opportunity to replace the castor bushes, the front lower control arm, lower the car and get the alignment dialled in with new tyres. I took it down to Alignment Motorsports on the GC to get this work done and also get more out of the Shockworks as I felt like I wasn't getting the full use out of them.  To cut a very long story short, it ended up being the case the passenger side castor arm wouldn't accept the brand new bush as the sleeve had worn badly enough to the point you could push the new bush in by hand and completely through. Trying a pair of TRD bushes didn't fix the issue either (I had originally gone with Hardrace bushes). We needed to urgently source another castor arm, and thankfully this was sourced and the guys at the shop worked on my car until 7pm on a Saturday to get everything done. The car rides a lot nicer now with the suspension dialled in properly. Lowered the car a little as well to suit the lower profile front tyres, and just bring the car down generally. Eternally thankful for the guys down at the shop to get the car sorted, we both pulled big favours from our contacts to get it done on the Saturday.  Also plugged in the new Stedi foglights into the S15, and even from a quick test in the garage I'm keen to see how they look out on the road. I had some concerns about the length of the LED body and whether it'd fit in the foglight housing but it's fine.  I've got a small window coming up next month where I'll likely get a little paint work done on the 110 to remove the rear wing, add a boot wing and roof wing, get the side skirt fixed up and colour match the little panel on the tail lights so that I can install some badges that I've kept in storage. I'm also tempted to put in a new pair of headlights on the 110.  Until then, here's some more pictures from Easter this year. 
    • joshuaho96
      R32 GTS (RB20DE) Injectors Replacement

      By joshuaho96 · Posted

      I would put a fuel pressure gauge between the filter and the fuel rail, see if it's maintaining good fuel pressure at idle going up to the point when it stalls. Do you see any strange behavior in commanded fuel leading up to the point when it stalls? You might have to start going through the service manual and doing a long list of sensor tests if it's not the fuel system for whatever reason.
×
×
  • Create New...