Jump to content
SAU Community

R32 gtst speedo out by 10kph

Kyer32

By Kyer32,
in General Maintenance

 Share

Recommended Posts

Duncan Grand Master

Duncan

Posted
Posted

It is normal for a speedo to read 0-10% high (unfortunately), intended by manufacturers and ADRs (although not in this case) to ensure your speedo does not read low if your tyres are worn.

Speaking of which, what size tyres do you have on the rear, and what does they tyre placard say you should have? you can use this https://tiresize.com/calculator/ to determine what % difference that is causing

Personally, when I buy tyres for a car I buy a size that will bring the speedo back to being more accurate; it if it reads 5% high I buy tyres that are 5% larger diameter. If you had an electronic speed sender like R33 onwards, the other option is to add a speedo adjuster but that won't work in R32. Finally, you  might be able to find a different sized gear for the speedo sender but that will be limited to what already exists (and I don't know what sizes do)

GTSBoy Grand Master

GTSBoy

Posted
Posted
7 hours ago, Kyer32 said:

so I need a new speedo cable 

Nope.

The seal is in the drive. A new cable would just fill up and continue to convey oil to the speedo head.

To check if this is what is happening, take the cluster out, dismantle the speedo and have a look. You probably don't even have to dismantle it. If there is oil coming up the cable, the drive into the speedo will be grossly greasy.

I had to manually (and delicately) clean the gunk out of my speedo.

Kyer32 Rookie

Kyer32

Posted
  • Author
Posted
On 8/1/2025 at 6:29 AM, Duncan said:

It is normal for a speedo to read 0-10% high (unfortunately), intended by manufacturers and ADRs (although not in this case) to ensure your speedo does not read low if your tyres are worn.

Speaking of which, what size tyres do you have on the rear, and what does they tyre placard say you should have? you can use this https://tiresize.com/calculator/ to determine what % difference that is causing

Personally, when I buy tyres for a car I buy a size that will bring the speedo back to being more accurate; it if it reads 5% high I buy tyres that are 5% larger diameter. If you had an electronic speed sender like R33 onwards, the other option is to add a speedo adjuster but that won't work in R32. Finally, you  might be able to find a different sized gear for the speedo sender but that will be limited to what already exists (and I don't know what sizes do)

 

1 minute ago, Kyer32 said:

My tyres are 215/45/r17 the 32 is a type m

 

Kyer32 Rookie

Kyer32

Posted
  • Author
Posted
On 8/1/2025 at 7:21 AM, GTSBoy said:

Nope.

The seal is in the drive. A new cable would just fill up and continue to convey oil to the speedo head.

To check if this is what is happening, take the cluster out, dismantle the speedo and have a look. You probably don't even have to dismantle it. If there is oil coming up the cable, the drive into the speedo will be grossly greasy.

I had to manually (and delicately) clean the gunk out of my speedo.

So if anything it’s be the seal speedo drive sorry it’s being awhile since I worked on one of these is the drive connected to the gearbox or behind the cluster 

PLYNX Mentor

PLYNX

Posted
Posted

Yep ! 

Cluster out first.

Dismantle.

Check for oil grease. If oil and grease = clean.

Then check seal at the drive coming from the gearbox. 

Seal broken  = change seal.

Doing it the other way around it will again push grease/oil back into the cluster and then your gonna have to do the cluster clean all over again !

 

Kyer32 Rookie

Kyer32

Posted
  • Author
Posted
On 7/1/2025 at 11:26 PM, GTSBoy said:

I would guess the seal has gone down at the speedo drive and gearbox oil has crept up the drive cable sheath and fouled the speedo head.

 

On 7/1/2025 at 11:32 PM, niZmO_Man said:

Your car was auto before? You have different diff ratio (auto vs manual i think? or n/a and turbo?)

 

1 minute ago, MBS206 said:

What makes you guess that tyre size specifically?

Just tried researching factory type m spec that’s all I can find 

niZmO_Man Grand Master

niZmO_Man

Posted
Posted

Search for your VIN in gtr-registry.com and see what it left with from factory. There's 4.3:1 and 4.11:1 diff ratios IIRC, can't remember what models had what.

Also could be tyre size, by factory the speedo reads a tad quicker >80 km/h but constantly out be 10 km/h is weird.

Maybe someone wound the odometer back, and accidentally bumped the needle up?

Kyer32 Rookie

Kyer32

Posted
  • Author
Posted
1 hour ago, niZmO_Man said:

Search for your VIN in gtr-registry.com and see what it left with from factory. There's 4.3:1 and 4.11:1 diff ratios IIRC, can't remember what models had what.

Also could be tyre size, by factory the speedo reads a tad quicker >80 km/h but constantly out be 10 km/h is weird.

Maybe someone wound the odometer back, and accidentally bumped the needle up?

Well found out it’s a 60th anniversary gtst from that it came with 205-55r15

-Jimmy- Mentor

-Jimmy-

Posted
Posted

Interesting, I haven't read about the issue with oil getting into the speedo in the cluster before. I'll have to take more notice with mine.

The speedo on my R32's when I've run factory diff and tyre size have never been accurate as far as I can remember.

On 1/12/2025 at 9:44 PM, GTSBoy said:

No R32 GTSt had 15" wheels. 205/55-16 was standard GTSt fare.

4.36:1 is standard R32 turbo auto diff. I think the manual was too, not 4.11.

4.11 and 4.08 were R33 namual and auto respectively.

The non Type-M GTS-t did come with 15" 5 stud wheels and smaller brakes, but that's less than 5% of them. :)

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now
 Share
Go to topic listing


  • Similar Content

  • Latest Posts

    • Murray_Calavera
      Steps to DIY sanding car back ready for respray....

      By Murray_Calavera · Posted

      Did you panel beat the dents or have you tried to repair this only using filler?  Is your sanding block soft/flexible and is following the shape of the panel rather then just knocking down the high points? 
    • silviaz
      Steps to DIY sanding car back ready for respray....

      By silviaz · Posted

      I haven't knocked them down yet. I think I made the repair more complex than it should have been. I had rock chips combined with waviness and dents and I tackled it all in one because it was near each other and just end up wasting a bunch of bog lol. I'll knock down those areas and see how I go. And yep what you are saying at the end is correct. I think I might be sanding the top of a steep hill then my sanding block falls into the dent and gets rid of the guidecoat if that makes sense. Though shouldnt unless I'm covering too big of an area with not a long enough block. I'll try something new and provide some updates. Getting there though! Thanks as always.  
    • Murray_Calavera
      Steps to DIY sanding car back ready for respray....

      By Murray_Calavera · Posted

      Yeah makes sense, hard to comment on your situation without seeing what your doing. I was talking generally before, I would not be looking to randomly create low spots with a hammer to then have to fill them.  It's hard without seeing what your doing, it sounds like you are using the guide coat to identify low spots, as you're saying the panel is still wavy. I don't see how you're not ending up with patches of guide coat remaining in a wavy panel? Once the high spots are knocked down to the correct level, surely to have a wavy panel you need low spots. And those low spots would have guide coat still in them?
    • silviaz
      Steps to DIY sanding car back ready for respray....

      By silviaz · Posted

      So I'll put filler past the repair area a bit to make sure I don't miss anything. Then I'll block it until it's almost level, put the guidecoat, then keep blocking until it's gone. Then it's still wavy.  In regards to hitting the panel, I saw this video might give more context - Skip to 0:47 he knocks it down. But yeah I'm sanding until the guidecoat is gone then checking because otherwise my filler is still well above the bodyline. Unless what you're saying is I should put guidecoat around it early, surrounding the filler then stip once it's gone?
    • GabsReDeal
      R32 GTS (RB20DE) Injectors Replacement

      By GabsReDeal · Posted

      I refreshed the OEM injectors with the kit and connected it up. It now ideals okay even with the IACV removed. Driving still has the same cutoff issue like the 550cc injectors so the issue is somewhere else. I bought FPG's Fuel Pump Hanger. I will be installing it next, but it is not as straightforward as I thought it was with my limited wiring knowledge and no instruction on the specific model I purchased (FPG-089). I also got the incorrect billet clamp as I could not find info on the OEM sizing.
×
×
  • Create New...