Jump to content
SAU Community

Recommended Posts

So my R32 GTST has been sitting around at my old mum and dad's place for a few years now...and it's time to bring it home.

Main issue I have is that she hasn't been started in about 5 years or so, so I'm not too keen on just kicking it over and hoping that RB20 reputation for being un-killlable extends to long periods of neglect.

My plan is to get it running there so I can move it around,  then get it towed back to my place where I can start working on it properly. The old folks driveway is a bad place to start a project like that. I'm getting old too and also haven't stuffed around with cars since forever, so kinda learning this stuff again.

So far I've siphoned out all the shitty old fuel and topped up the coolant (thought it was fully dry but took 2 litres to fill the radiator). Planning on hitting the rusty rotors with some brake cleaner in case the tow truck driver gets a bit gung ho loading it up. As far as oil, it's got plenty although it's now dark in colour and obviously needs a change sooner rather than later.

Was doing some YouTube research and was planning to hand-crank the motor from the harmonic balancer with a 37mm socket and breaker bar, removing the spark plugs and spraying some "fogging oil" in the holes but there's not much room to get in there with the radiator fan right up against it. Jacking the car up takes too long and I can't leave it half done between visits.

So now I'm was thinking of cranking a few times it using the starter (removing plugs and spraying oil first). Reckon there's any chance it will do more damage that way if something's stuck inside the motor? Should I really change all fluids completely before I go any further?

Grateful for any other advice you guys have to get her going safely too.

 

 

 

Link to comment
https://www.sau.com.au/forums/topic/486162-starting-again/
Share on other sites

15 minutes ago, Ozdavroz said:

thought it was fully dry but took 2 litres to fill the radiator

You may well find that there is a big air bubble in there and plenty more coolant will be swallowed once it starts. So keep the bottle handy.

17 minutes ago, Ozdavroz said:

Was doing some YouTube research and was planning to hand-crank the motor from the harmonic balancer with a 37mm socket and breaker bar, removing the spark plugs and spraying some "fogging oil" in the holes but there's not much room to get in there with the radiator fan right up against it. Jacking the car up takes too long and I can't leave it half done between visits.

If you can roll it back and forth, you can make the pistons go up and down a bit by putting it in 3rd or 4th and giving it a shove.

Link to comment
https://www.sau.com.au/forums/topic/486162-starting-again/#findComment-7998366
Share on other sites

14 minutes ago, GTSBoy said:

If you can roll it back and forth, you can make the pistons go up and down a bit by putting it in 3rd or 4th and giving it a shove.

This sounds do-able except space is a little tight were it's currently sitting. How many metres you reckon it would need to go?

Link to comment
https://www.sau.com.au/forums/topic/486162-starting-again/#findComment-7998370
Share on other sites

It's fine. Basically if it has seized (eg due to moisture/rust in the bores) it will either break free on the starter or it won't turn....then you'll know it is freed up

If it turns and doesn't start (reasonably likely) you will need to troubleshoot but most likely issue is a seized injector from moisture; same if it starts but missfires.

Anything else could have happened (eg mice nibbling electricals) but the only way to find out is to close your eyes and hit the key

I'd also change the fuel filter again after a few minutes of running as it may catch a heap of crap on first start

  • Thanks 1
Link to comment
https://www.sau.com.au/forums/topic/486162-starting-again/#findComment-7998372
Share on other sites

19 minutes ago, Ozdavroz said:

This sounds do-able except space is a little tight were it's currently sitting. How many metres you reckon it would need to go?

Not far. If all you want to do is know that they will reciprocate and move oil around a tiny bit, then a metre or so is all you need. Half metre fore and aft is enough.

  • Thanks 1
Link to comment
https://www.sau.com.au/forums/topic/486162-starting-again/#findComment-7998374
Share on other sites

I wouldn't even move it like gTSBoy is saying. I'd seriously do what Duncan is saying.

Unplug the injectors, and unplug the fuel pump. 

Pull the spark plugs out. Have a look in quickly with a bore scope if you want.

At most, you can't spray a bit of oil into the bores so there is lubricant in there while you crank it. (Don't fill it, as it's only going to enter the exhaust, or spit at you out the spark plugs holes.

Before cranking the engine on the starter, after a 5 year sit I'd probably prime the oil system manually.

Easiest way to do so is to look at buying an oil filter relocation block, fit it to the engine. The pressure line going into the engine on this block you can then shove into some sort of oil pump, or put it into a bottle, with that hose going to the bottom. Fill bottle up with oil. Now seal the bottle and add a compressed air line to the top of the bottle. Feed compressed air in, about 20psi will be PLENTY. This will pump oil through the motor. Be aware, it also means it will drain back to the sump, so make sure you don't end up over filling the motor ;)

Now bolt the old oil setup back on (or fully install the remote filter system).

 

This way you've at least pushed fresh oil everywhere, then you're letting the motor crank to then do its own oiling.

Then I'd tap the key to make sure it can start to crank, if the motor free bumps, then I'd just hit the key and let it crank.

After letting it crank and seeing you can get real engine oil pressure, put new spark plugs in, reconnect the fuel system electrics, and send it.

 

Additionally, you can look to remove the fuel feed line to the rail, and divert it to a tank so you can get the bottom of the tank shit out, and just incase there's some crud sitting anywhere that gets passed the fuel filter (or is already ahead of it).

 

If fuel injection at the injectors ends up appearing to be a problem, you can dump the injectors into an ultrasonic cleaner for a quick flush clean out. Note this isn't as good as new injectors, or getting them pro cleaned and flowed ;)

 

 

  • Thanks 1
Link to comment
https://www.sau.com.au/forums/topic/486162-starting-again/#findComment-7998391
Share on other sites

Personally I would first drain the oil thats in the sump.. and stick something else in.. something cheap.. which id then replace once its idled for a wee bit.

Fogging oil is usually done before you put it away - I use that on mine.. as I store it for a whole year every year.

Your injectors might be stuck, if running an aftermarket ecu you can easily test each one.

 

  • Thanks 1
Link to comment
https://www.sau.com.au/forums/topic/486162-starting-again/#findComment-7998456
Share on other sites

  • 3 months later...

Quick update, finally got an hour or two on a weekend where there wasn't shit weather, no sick kids, people visiting our house or had to work. Visited me old folks and the skyline...dropped  $10 of 98 in the tank and a brand new SCA shitter battery in. Cranked over a bunch of times but didn't fire up....pretty sure it's not getting any fuel. Gonna try some of the stuff suggested above, next time I make it over there. 

Link to comment
https://www.sau.com.au/forums/topic/486162-starting-again/#findComment-8002043
Share on other sites

Had another look at the car and I noticed the fuel pump isn't priming on ignition. I'd taken out the pump from the boot to siphon out the old fuel, so maybe I've knocked something loose or broken a wire putting things back together. Will go back with a multimeter and try to work out what's stuffed. Kinda hoping it's the pump itself thats gone so I can upgrade it

  • Like 1
Link to comment
https://www.sau.com.au/forums/topic/486162-starting-again/#findComment-8002148
Share on other sites

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now



  • Similar Content

  • Latest Posts

    • Hi from Canada, Both of my calipers are starting to fail. My car is a 2005 M35 Stagea ARX and I can't seem to find any parts or any cross reference caliper that would fit my car. Is there a company or a similar caliper that would fit and I could replace the OEM one. Or if anyone knows where I can find a new OEM. Any help is very appreciated. Let me know!
    • Maf is a question mark but TPS  I have set at 0.47, the fact that I’m getting proper voltage range out of it with the key on leads me to believe it’s functioning properly. I’m getting proper voltages on basically everything. I still need to look up voltage ranges for z32 maf and test that 
    • Honestly no not at all, but it’s a very basic tune, it’s stock injectors q45 tps and z32 maf. Other than that it’s a completely stock base map. The file is from nistune and from my understanding if it was tune related I would be able to unplug maf and tps and it would still start even if it was a really shitty start. I have tried starting it with coolant temp, maf, and tps unplugged none of those 3 togethor or individually changes anything 
    • 🏆 Skyline Supremacy Meets Mount Panorama Magic 🏆 Join SAU NSW as we take the long way to Bathurst, the home of GTR greatness. Saturday 30th August 2025 7:00AM Meeting Hanna Park North Richmond 7:30AM Departure Cruise Via Bells of Line Road 9:00AM Arrival to Stop 1: Golden Poplars Meadow Flat 9:45AM Arrival to Final Destination: Mount Panorama Motor Racing Circuit Meet Location: Hanna Park North Richmond Stop 1: Golden Poplars Meadow Flat Final Destination: Mount Panorama Motor Racing Circuit   *Disclaimer* There will be a lead and follow car so no one should get lost. If you would like to attend or bring others along please put your name down and a +1 as numbers will be needed prior! This is NOT a race and we will all be adhering to all road rules. If this is what you want please come to one of our many track days. This is an official SAU:NSW event and will be run under a CAMS permit. One of the things that really sets our club apart is our commitment to being true enthusiasts. When on normal roads we strive to maintain good relations with the authorities as well as the public in general. When attending one of Skylines Australia NSW events please try to: • Be aware of surrounding environment and act accordingly. • Drive courteously on the state’s roads as a true enthusiast should. • Understand how important it is to maintain the good name of SAU NSW and thus, treat others accordingly. • Any misbehavior will not be tolerated and you will be asked to leave.
    • What does it look like with highway driving? And yes, I had a similar thought as Duncan. It looks quite similar in my Stagea and I have made myself accept it as normal. Might have to look into it some day   Highway gets as low as 10l/100km on my end so I'm not as worried about it being a mechanical issue. More likely just the tune on the haltech.
×
×
  • Create New...