Jump to content
SAU Community

Recommended Posts

Prue you should try to find yourself an EA position in a public service org like Centrelink/DHS/Medicare. You'd almost certainly be located here in tuggers, and it's practically a glorified secretary :P that, and you'd be hard-pressed to even find one lower than APS4

I used to work over in Woden for the department of health & ageing & apparently they're going to have a shitload of EA positions opening up soon so my dads going to send me all the info when it comes out.

Hello territorians,

I'm trying to contact OKBANANA (Dallas S), as I purchased a R34 Alternator My link from him over a month ago and after confirming that he had sent it, then said it was returned to his house, now he won't answer his phone, emails or text. I realise he works for the government and works away on occasion so I'm trying to give this the benefit of the doubt, but dead silence is not helping.

Maybe someone on the forum/ACT area knows his situation??

Thanks

Pretty sure he'll sort it out and be back in contact as soon as he can.

He's not on here often. Last post was around end of Feb when he mentioned some work to be done in 3 weeks time.

So I'd say after the 21st sometime.

It's possible he's away at the moment, only on the last page of this thread you can see he was looking for anyone to help him with removing the engine from his car but not until 3 weeks time. Also he doesn't strike me as someone to rip another person off, seems to have a good forum standing so why would he ruin it?

Best of luck though, hopefully he should read this asap and contact you :)

Just noticed I'm a bit of a Postwhore without the post

Here comes the Rain, lucky I'm inside with a cold drink and some choice music.

Better put the roast pork on or there will be no crackling...gotta love that crackling Mmmmmm

Bored?.....yeh just a little :cheers:

It's possible he's away at the moment, only on the last page of this thread you can see he was looking for anyone to help him with removing the engine from his car but not until 3 weeks time. Also he doesn't strike me as someone to rip another person off, seems to have a good forum standing so why would he ruin it?

Best of luck though, hopefully he should read this asap and contact you :)

Thanks for the update guys, we'll wait till then and see what happens!

as in the angle???

mine are shocking, so dim its not funny and they look horrid on lo beam cant see anything. hi beam goes well though...

as for adjusting...no idea...but from everything i have seen the clips are more of a one position only???

Yeah, sorry, should have been more specific. They need to be adjusted up.

There are tilt screws on the back, but they dont seem to be doing anything?

This afternoon was really shit on the Tuggers express way coming home. The anger mgmt sessions did not help me cope with the congestion caused by 2 big tractors in the right lane and a bunch of f**ken hopless arsehole muther f**kin dream boats in cars without a clue of how to overtake on the left. Grid lock from civic to woden - Vent completed

:rant:

PS. Did you know CNUTS displays as "dream boats" LMFAO

Edited by Sinista32

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now



  • Similar Content

  • Latest Posts

    • Yep, the closest base tune available was for the GTT, I went with that and made all the logical changes I could find to convert it to Naturally Aspirated. It will rev fine in Neutral to redline but it will be cutting nearly 50% fuel the whole way.  If I let it tune the fuel map to start with that much less fuel it wont run right and has a hard time applying corrections.  These 50% cuts are with a fuel map already about half of what the GTT tune had.  I was having a whole lot of bogging when applying any throttle but seem to have fixed that for no load situations with very aggressive transient throttle settings. I made the corrections to my injectors with data I found for them online, FBCJC100 flowing 306cc.  I'll have to look to see if I can find the Cam section. I have the Bosch 4.9 from Haltech. My manifold pressure when watching it live is always in -5.9 psi/inHg
    • Hi My Tokico BM50 Brake master cylinder has a leak from the hole between the two outlets (M10x1) for brake pipes, I have attached a photo. Can anyone tell me what that hole is and what has failed to allow brake fluid to escape from it, I have looked on line and asked questions on UK forums but can not find the answer, if anyone can enlighten me I would be most grateful.
    • It will be a software setting. I don't believe many on here ever used AEM. And they're now a discontinued product,that's really hard to find any easy answers on. If it were Link or Haltech, someone would be able to just send you a ECU file though.
    • Yes sir am asking is there possible way from aem tuner from wiring pins 
    • Have you checked cam to crank timing and confirmed balancer marks are correct?
×
×
  • Create New...