Jump to content
SAU Community

Recommended Posts

phone LCD screen replacements

anyone know who/where does this and can be trusted ?

I have 2 HTC Mobile phones where I have cracked the screen

These are worth $450 and $650 bucks so I'd like to see if I can repair them

all help appreciated :)

I've done it before on HTC depends which model it is I can probably do it for you. Sometimes you have to get the LCD plus the digitizer because it's nearly impossible to seperate them.

You can try the phone shop vendors in tuggers mall or Woden infront of Vodafone

Soda blasting was used on my GTR bonnet. Very gently but still managed to rip a whole in the alloy bonnet.

I think in the hands of an experienced operator it has it's benefits.

I expect rubber and sills need to be covered correctly or avoided.

Ive always done my cars prep by hand. The whole lot. Takes a long time but you get better results. Hope damage was not too bad Mik.

The rubbers can be fixed, they are old and hard and can be sanded back, maybe thats why the soda did that.

The plastic bit in the back window seal is fked anyway, i might cut it out and do a bead of sealant in the gap.

So in hindsight, you can sand just as close or closer than you can blast, and blasting lifts the rubber and leaves crud under there.

Im glad i only did a couple of spots, ill have to clean behind the rubber to get it sitting flush again.

post-89755-0-06799200-1392885986_thumb.jpg

Its good for getting paint out of the tight corners, and probly good for cleaning small metal parts

Its not working properly, the guy sent a bag of the wrong soda, so it clogs up. It works with constant shaking, but thats kinda hard to do while your trying to use it.

I cant get blasting soda in canberra that i know of, and the car will be primed before the right stuff turns up....... :/

Maybe ill do the old wheels or something.

Caught up with a few mates and went for a quick cruise - they met up with the Braddon guys... left there not wanting to be around kidz doing fatty skiddiez. So went up to Mt Ansilie and chatted about Initial D with a m8 who tagged along then went home. So good taking Rosie out for a long nip :)

Spotted a R33 GTR and a white R34 GTT and about 50 SS's haha

Edited by RosieR34

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now



  • Similar Content

  • Latest Posts

    • Well, the trouble with that ^^ is: The configuration shown is absolutely a 1-way, not a 1.5-way. There is no way that a 1.5-way can be said to offer LSD action only on acceleration. If Nismo cannot get that right, then it is impossible to believe their documentation. That ^ is not a 1.5 way setup. That is a 1-way.   And so now I have allowed all doubts to flourish and have gone back to look at the MotoIQ video. I originally made the mistake of believing him when he said "this is a 1.5-way" at the ~6:10 mark. Because what he did was take the gear assembly out of the 2-way opening and just rotate it one place to the left to drop it into the 1-way opening. When he dropped it in there, the cam was "backwards" compared to the correct orientation shown in all other photos of that config. The flat shold have been facing the 1° ramp side of the opening, not the 55° ramp side. And I thought, "gee that's cute", but I was concerned at the time, when he put the other ring back on, that the gap between the rings looked like it was wider then in the 2-way config. And then I said a lot of things in my long post on Tuesday that could only make sense if the guy from MotoIQ was correct about what he'd done. BUT... I have now done my homework. I grabbed a frame of the video with the 2-way config, and then grabbed another with the "1.5-way" config, snipped out the cam and opening of that frame and just pasted it direct on top of the 2-way config. I scaled it so that the triangular opening was almost exactly the same height in both. AND.... the gap between the plates is wider with the cam installed in the triangualr opening backwards. That is.... it cannot go together that way. There would be massive force on the plates all the time, if you could even reassemble it.  So, My statement on the matter? The Nismo diff is actually only a 2-way and 1-way. There is no 1.5-way option in it, regardless of what they say. Here's a photo of a real 1.5-way ramp opening from Cusco (along with the 1 way option). And the full set of 1 through 2 way options from their racing diff, which is not same-same as what we'd typically be using, but...the cams work the same. A little blurry, but it comes from this Cusco doc, which is quite helpful. AND.... Cusco do in fact do what I suggested would be sensible, which is to have rings that do 1 and 1.5, and 1.5 and 2. Separately.  
    • Welcome Adam. Car looks great!
    • "With a 1.5-WAY, the LSD is effective only during acceleration."
    • Well it wasn't as easy as I thought.... and it also wasn't in my original manual which I did end up finding. They discuss the process in the Nismo catalogue though and it requires slight machining. Page 145.  NISMO PARTS CATALOGUE 2020
    • I'm an idiot, my intercooler is rated for 1000hp. I had clicked on the wrong product. Knowing the delta P would be nice, but I'm doubtful I'll do it. Now as for an EMAP, that would be great and I'll get around to it eventually but from my findings in my last post, I'm considering a turbo swap now. 
×
×
  • Create New...