Jump to content
SAU Community

Recommended Posts

phone LCD screen replacements

anyone know who/where does this and can be trusted ?

I have 2 HTC Mobile phones where I have cracked the screen

These are worth $450 and $650 bucks so I'd like to see if I can repair them

all help appreciated :)

I've done it before on HTC depends which model it is I can probably do it for you. Sometimes you have to get the LCD plus the digitizer because it's nearly impossible to seperate them.

You can try the phone shop vendors in tuggers mall or Woden infront of Vodafone

Soda blasting was used on my GTR bonnet. Very gently but still managed to rip a whole in the alloy bonnet.

I think in the hands of an experienced operator it has it's benefits.

I expect rubber and sills need to be covered correctly or avoided.

Ive always done my cars prep by hand. The whole lot. Takes a long time but you get better results. Hope damage was not too bad Mik.

The rubbers can be fixed, they are old and hard and can be sanded back, maybe thats why the soda did that.

The plastic bit in the back window seal is fked anyway, i might cut it out and do a bead of sealant in the gap.

So in hindsight, you can sand just as close or closer than you can blast, and blasting lifts the rubber and leaves crud under there.

Im glad i only did a couple of spots, ill have to clean behind the rubber to get it sitting flush again.

post-89755-0-06799200-1392885986_thumb.jpg

Its good for getting paint out of the tight corners, and probly good for cleaning small metal parts

Its not working properly, the guy sent a bag of the wrong soda, so it clogs up. It works with constant shaking, but thats kinda hard to do while your trying to use it.

I cant get blasting soda in canberra that i know of, and the car will be primed before the right stuff turns up....... :/

Maybe ill do the old wheels or something.

Caught up with a few mates and went for a quick cruise - they met up with the Braddon guys... left there not wanting to be around kidz doing fatty skiddiez. So went up to Mt Ansilie and chatted about Initial D with a m8 who tagged along then went home. So good taking Rosie out for a long nip :)

Spotted a R33 GTR and a white R34 GTT and about 50 SS's haha

Edited by RosieR34

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now



  • Similar Content

  • Latest Posts

    • Thank you, 100% the intent. New coils were due and the 17" sixers look/feel loads better than the stock wheels. The aero options are so spot on.   Thanks for the warm welcome, all!
    • 98 r34 gtt Been rocking my latest setup and car running like never before. Have put a good 200 miles on it since all the latest changes and additions. everything is dialed in and have been driving it a bunch.   However, all a sudden last weekend as soon as I pushed throttle passed 4k and the engine stumbles, (slow or fast acceleration) hesitates and doesn’t go above 4100 or so, like a misfire. Everything else seems fine. I had a “good” set of coil packs that I removed from car when I first got it when I changed them over to new coils. I swapped out current ones for those, but no change. I also changed the plugs, no change. Seems to rev over 4 when out of gear with no load just fine no “misfire”, but as soon as its in gear with a load of any kind, it “misfires” as soon as rpm drop back below 4 k it runs perfectly, smooth, starts, restarts and drives fine as long as I keep it below 4 k while in gear. All readings look fine, no CEL   Any idea as to what could all a sudden cause an issue when pushing rpms passed 4 k?
    • When you say your cams are 272/262 is that 272in and 262ex?
    • We're arguing semantics. I am saying 45 accel and a 55 deccel ramp are "2 ways". Even a 45 degree ramp and an 89 degree ramp is "2 ways", because it is literally... two ways. The cusco 55/30 ramp is a 2 way. It's two ways. I get it though - in normal nomenclature a "2 way" would be 45/45 or 55/55 or 60/60 i.e the same locking in both directions. And something like 45/65 would be considered "1.5 way". I would then say if we're getting into the nitty gritty then every locking diff is a "2 way" diff and we should not speak in 1.5, or 2 ways but ramp angles instead. Which ofc if one of those ramp angles is 90deg, that side is not doing any locking. :p So Nismo don't obviously sell 3 things. The fact of the matter that they only sell two items really goes to show that there's a 2 way and a "1,5 way" which is really a 1 way. I believe the actual lockup for the 'adjustability' of the GT pro is really just setting preload for when the ramps actually start locking up. It's not changing how much 'wayness' there is. It is (somehow) horribly explained. People just buy whatever diff and go "locks up good bruh" and that's what ends up on socials forever.  
×
×
  • Create New...