Jump to content
SAU Community

Recommended Posts

Cool. Any idea the best place to get one? Closed my door when I got home and the window exploded!

That is Crazy! Do you think it was touching something hard inside the door?

or maybe too much air pressure inside... Seals too good.

Trojan? or whatever JapSpec turned into?

or Try Jap Parts in Fyshwick maybe...

Damian 0449775209 -

Ph: 6280 0606

Ah: 6280 8898

Tell him Rob with the R31 Wagon sent ya! :thumbsup:

hmm that is strange....I agree it seems likely it either hit something inside or maybe the lower seal is rusted/loose?

anyway, if you find a window in Sydney I can bring it down next week.

Bub wanted to get up at 5 this morning.....

Lucky he did, i found water spreading across the lino floor.

One of the fishtanks is leaking. Emptied it out, fish in a bucket, took it outside.

Good excuse to get rid of it...... dont tell the missus i said that. ;)

less fish time=more skyline time

Anyone want a pair of Angelfish?

Edited by D.I.Y. Mik

I once had an old Pintara as a daily that someone smashed the window on. We got the window from the wreckers and I can't remember it taking Pete more than a couple of hours all up to fix?

Different car but still Nissan with all electric bits etc.

Surprised also if there's not a tutorial on here how to do it somewhere.

Hi Eric - have done it twice on my 32

It's not complex at all but the first time will take 1-2hrs. It's mainly about the angle of getting glass out/in.

Make certain you give it a great vacuum if the glass has shattered.

It gets every where but particularly on the brushes and inner/outer window strips

Which means if you don't do it properly your new (2nd hand) window will scratch-up the first time you put it up/down.

It's 10 minst to get the door card off and all the window switches out and unplugged

bout 10-20 to undo the nuts holding the window in

bout 10-20mins removing the window - but if yours is shattered just the thourough vacuum and removal of broken glass.

I did it alone but it would be a lot easier if there are 2 of you. Just balancing the window, slotting it in and doing the nuts up whilst the other holds the galss in place.

TFE mate.

$150 for a window and $300 to install it.

How hard are they to install? Anyone have any idea?

Cheers.

It wont be too hard would just need 2 sets of hands to do it.

I might be able to assist tomorrow night if you need

yeah DIY is very do-able, cleaning it out is the pain as said above. Also check for rust in the channel that holds the window, and also rust or damage to the "waist mould" that goes along the top of the door.

the only other issue can be adjusting the window afterwards (we had heaps of trouble in the 350z) but I think a 33 should be old enough to just do a straight replacement without any annoying adjustments.

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now



  • Similar Content

  • Latest Posts

    • The wideband reading is meaningless if it's not running. Why are you using shitty old sidefeeds on any engine, let alone a Neo? What manifold and fuel rail are you using to achieve that? Beyond that, can't help you with AEM stuff as I've never been their ECU/CAS combo.
    • Manual boost controllers (where a little of the boost was bled off) were quite common back in the day, because they were cheap and easy. Generally they had a manual adjustment screw rather than being fixed like yours. Down side is they always bleed boost, not just when you want them to so an electronic boost controller that uses a solenoid will have less lag.
    • Hello , im new here and i have A31 home build  RB25det neo stock eng / turbo  aem ems 2 blue connector  aem 3.5 map aem cas disk aem wideband connected to ecu  355 lph pump 550 nismo yellow injectors side feed aftermarket regulator  and won’t start with base aem tuner basic tune eventually flipped cas 180 degree so it triggers on correct stroke not in exhaust cycle  Now it won’t start Wideband reads 10 and 11 at lowest fuel setting  and will share calibrations soon for aem tuner i think something is wrong in aem tuner    please if you have any information, am very grateful         
    • Legend. I ended up finding the facebook account of the owner of the first car i sent but sadly he deactivated the account. I think you’re right in saying it’s some sort of well done custom job. Really appreciate your help anyways.
    • Totally equivalent. Stock often goes from the comp cover because that's where the actuator is also installed and the factory needs 2" of hose to make the connection - and it comes as a pre-assembled unit. They totally have a boost reference from somewhere between the turbo and the throttle(s). Oh, jeez. Just do it in M12 then. We don't actually care that much. I would expect any such AN converter fitting to rely on an o-ring or some other seal onto a flat surface under the flange of the hex**, because bolt threads are no intended to provide a pressure seal. unlike..... pipe threads. **which also requires a suitably flat and smooth surface on the turbo's boss to provide the seal.
×
×
  • Create New...