Jump to content
SAU Community

Recommended Posts

I have two to try, one is a HKS style split dump pipe, and the other is a dump/front pipe in one of a mates R33, judging by whats for sale in the shops the 33 and 32 front/dump pipes you can buy fir both no probs

Hoping to try both out

Will be doing it cold, first thing in the morning I hope

Plan is to removal the exhaust manifold heat shield etc and un-bolt it and bolt the other one up, hopefully :D

...and done it for you.

Long extension and undo three nuts (dump-front pipe) it should sit after dropping a bit if all OEM bkts are there.

10mm 1/4 drive and undo the bolts in the small turbo shield... unplug o2 sensor. 10mm ringy for the sheild bolts down near shock tower. These are brittle and may break (Clean thread and use copper eze when replacing)

Undo stubbie... think about it for a while.

No dramas really

TT

PS Did you say you had some spades that fit the ecu plug off a wreck? Need a couple.

it is essential to have the car on a hoist to get to the turbo bolts? or can i jack it up or park it upcurve to get to the cat and turbo bolts?

any1 has an idea which cable is the oxigen sensor.....rb25det has 3..... but im not sure which one to connet the air/fuel gauge cable to???? any help?

Dump pipe came of no probs, made sure I gave the bolts a good soak and didn't snap anything!

Problem was the two dump pipes had differant exhaust stud pattern, so it all came off ok............and had to go back on :)

3.5" dump next week, funnily enough, my car is making 205rwkw with a 2.5"dump and front pipe...........and a pair of 2" gaskets on the cat...........dodgy!!

Just by replacing the gaskets saw boost jump up a bit, so hopefully with a 3.5" dump, there is a few more kw's to be had

Cheers for all the help/suggestions guys :P

Chris

  • 2 weeks later...

Has anyone ever had a problem with the stud bolt snapping off in the turbo when removing the dump pipe?

I'm going to be changing my dump pipe this weekend. I would really like to know if I have to prepare myself for the painfull process of removing broken stud bolts.

The car is a 95 GTST,

Replys would be greatly appreciated, so if you have done it could you post up what happened either way.

Cheers,

:whackit:

wooho.... goddamn is hot...

i jst replace ma dumpipe & frontpie....

the secret to NOT snapping the bolts is to tighten the bolts jst a tiny bit, sot that the locked treads unlock.... then undo the bolts with patients....shouldnt be to hard....

but dont make the mistake i made... make sure to put the turbo heat-shield back on.... it realy makes a dif temp wise in the bay...

if your gaskets, either turbo gasket or cat gasket are Copper gaskets, use these instead of the cheapo silver paper thingies.....

i beta get bak to undoin ma pipes to put heat-shield back on....... :)

the best stuff to spray on the rusted corroded bolts is, 'rost off plus' it's made by worth, im a truck mechanic and we have found it's the best thing for turbo and exhaust manifold bolts. it's not cheap but quality comes at a price..

cos dont we all hate drilling out broken bolts.

  • 4 weeks later...

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • Well, I can recommend the partial AV system translation CD I ordered from Car Audio Workshop in NZ. Whilst it didn't address the date issue, it has conveniently translated on-screen menu items into English, and now allows the GPS-received time to be offset in hours rather than minutes, so I can display Eastern Australian time accurately ( and bump it by another hour when daylight savings starts ).
    • Yuh, if it's 45°C outside, my car is driving in it.
    • I'd be curious to hear more. Otherwise, have you driven a modern x-trail? I wonder how it compares. Here in Australia they are/were popular for rentals and fleet vehicles. I have been in some and my impression was they are bad. But, this may have been very different in the 2000s at a good trim level. Twenty years is plenty of time to make the model worse. I do very much agree with the 2 silver cars in the garage approach. But, not driving because it's too hot would not leave a lot of time in the year for many Australians. I don't think you need to worry too much unless the car has actual issues with overheating. 
    • Back again. I returned to Japan in Jul/Aug to spend time with the car on my birthday and remind myself what all the sacrifice and compromise is for. It happened to line up with the monthly morning meet in Okutama, which I have been wanting to go to for a long time. It's a unique event at a unique spot with really rare, interesting, and quirky cars. It's where all the oldheads and OGs gather. The nighttime scene at DKF certainly has its place and should be experienced if you're into cars, but there's too much bad attention and negativity around it now. IMO the better time is Sunday morning at DKF or Okutama; it's more chill and relaxed. I'm glad I was finally able to go, but not sure it's worth the drive from all the way from Nagoya immediately the day before, unless I was already staying in Tokyo for the days right before the meet, because you have to wake up quite early to make it in time. Funnily enough though I didn't drive the car all that much this trip because it was just too damn hot. While there were zero issues and running temps were nominal and the A/C was strong, RBs already run crazy hot as it is. Sure, it took it all like a champ but something about driving these cars in the ridiculous heat/humidity bothers me and makes me feel like I'm asking too much of it. I'm just me being weird and treating the car like a living thing with feelings; I'm mechanically sympathetic to a fault. Instead I was mainly driving something else around - a KX4(silver) 2001 X-Trail GT, that I acquired in May. There's a few different flavors to choose from with Xs, but visually it's the Nissan version of the Honda CR-V. Mechanically it's a whole different story as this, being the top-trim GT, has an SR20VET mated to a four-speed auto and full-time AWD! It was a very affordable buy in exceptional condition inside and out, with very low mileage...only 48k kms. Most likely it was owned by an older person who kept it garaged and well-maintained, so I'm really happy with how it all worked out. It literally needs zero attention at the moment, albeit except for some minor visual touch-ups. I wanted something quirky, interesting, and practical and for sure it handily delivers on all three of those aspects. I was immediately able to utilize the cargo and passenger capacity to its full extent. It's a lot of fun to drive and is quite punchy through 1st and 2nd. It's very unassuming -in the twisty bits it's a lot more composed than one would think at a glance- and it'll be even better once I get better tires on it(yes, it's an SUV but still a little boat-y for my liking). So...now I have two golden-era Nissans in silver. One sports car and one that does everything else; the perfect two-car solution I think👍 The rest of the trip...I was able to turn my stressed brain off and enjoy it, although I didn't quite get to do as much as I thought. I did some interesting things, met some interesting people, and happened into some interesting situations however, that's all for another post though only if people really want to know. Project-wise, I went back to Mine's again to discuss more plans and am hoping to wrap that up real soon; keep watching this space if that interests you. Additionally, while working in the tormenting sweatbox that is the warehouse, I was able to organize most of the myriad of parts that my friend is storing for me along with the cars, and the 34 has a nice little spot carved out for it: And since it can get so stupid hot in there, that made it all the more easy -after I was standing there looking at the car and said 'f**k it'- to finally remove all the damn gauges that have mostly been an eyesore all this time. Huzzah. The heat basically makes the adhesive backing on the gauge mounts more pliable to work with, so it was far less stressful getting this done. I didn't fully clean it up or chase the wiring though; that will happen once I have the car in closer possession. Another major reason to remove all that stuff is to give people less reasons to get in my car and steal s**t while it's being exported/imported when/if the time comes, which leads us to my next point... ...and that is even though it's time in Japan is technically almost up since it's a November car and the X would be coming in March, I'm still not entirely sure where my life and career is headed; I don't really know what the future looks like and where I'm going to end up. I feel there's a great deal of uncertainty with me and as a result of that, it feels like I'm at a crossroads moreso now than any point in my life thus far and there are some choices I need to make. Yes, I've had some years to consider things and prepare myself, however too much has happened in that time to maintain confidence and everything feels so up in the air; tenuous one might say. Simply put, there's just too much nonsense going on right now from multiple vectors. Admittedly, I'm struggling to stay in the game and keep my eyes on the prize. So much so in fact, that very recently I came the closest I ever have before to calling it quits outright; selling everything and moving on and not looking back. The astute among you will pick up on key subtext within this paragraph. In the meantime I've still managed to slowly acquire some final bits for the car, but it feels nice knowing there's not much left to get and I'm almost across that finish line; I have almost everything I'll ever want for my interpretation and expression on what it is I think an R34 should be. 'til later.
    • Thanks for that, hadn’t used my brain enough to think about that. 
×
×
  • Create New...