Jump to content
SAU Community

First F**K Up on my car... help please :(


Recommended Posts

Tonight my nightmare is a reality... it was only a matter of time????

Picked up my car from getting a service today and drove to my basketball game tonight... everything is sweet - better than good. It has never run so smooth and glide through the RPM's.

So with this and a whole lot of adrenalin running through the veins from the b/ball game I give it nice boot coming out of the stadium and down the Hwy about 30min. ago. When I hit 1 bar of boost or around 6300rpm all kinds of shit starts happening. Revs are going up and down, power on then off, feels like the rev limiter is kicking in early.. I cant get the car to boost above 1 bar... sounds real shit and feel's like somthing is about to blow up.

Any ideas??

Easy fix?

Besides that it still drives great up to 1 bar of boost ;)

"See what happens when you play rough with your toys!" (mum... about age 5 or 6)

Link to comment
https://www.sau.com.au/forums/topic/58748-first-fk-up-on-my-car-help-please/
Share on other sites

A. Just general service.. oil (MUTOL 8100), gearbox oil, oil filter, pressure test cooling system, clean air filters (I do have dodge filters though) - Just take it to the place next door to me. He has been doing my cars for years.

B. No plugs replaced. NGK plat. plugs still good.

Sound expensive???

Talking to my brother-in law he thinks it could be a fuel cut defender or something???

Any other ideas. Anyone willing to have a looks'ie. I'm on holidays and it christmas soon and dont really want to splerg on the car in December.

You will have to have a look at what ecu you are running, a better description of what is happening at what revs etc etc. Look on the bright side, electrical dramas are usually cheap to fix, if not a little frustrating to identify. Better then a spun bearing or a rod out th eside of the block:)

Perhaps a mod list?

... doesnt matter what u got done... its what THEY did to it when taking it round the streets ;)

Nah... don't think so. As I said it is litterally next door to me and I was home all day while he had the car and I can hear my car getting tharshed from about a block away (when my brother-in law drives it) + the dude is old and I don't think he would be into thrashing the car around.

Soon as I picked it up this afternoon I did take it around the block and picked up the GF from Chaddy at about 6pm also... all was good including above 1 bar of boost???

You will have to have a look at what ecu you are running, a better description of what is happening at what revs etc etc. Look on the bright side, electrical dramas are usually cheap to fix, if not a little frustrating to identify. Better then a spun bearing or a rod out th eside of the block:)

Perhaps a mod list?

Spoke to you @ B Battle on the weekend (keep it quiet... but I haven't checked what ECU it's running yet ;)) My bad...

Keeping my spirits high hoping it's a elec. problem or something that won't cost over $500 to fix.

I will give you all I can now anyways:

Trust T78 33D kit

Trust F/Mout Intercooler

Twin Filters with AFM's (that's 2 AFM's)

Oil Cooler

GReddy Profec B Boost controller (analog type...buttons)

ECU... will let you know tomorrow :D

Standard CAT... on my to do list.

Other stuff but I don't think that they would be the cause of the problem..

T/Timer

RSM (dodgy unit... but it works)

Tonight my nightmare is a reality... it was only a matter of time????

Picked up my car from getting a service today and drove to my basketball game tonight... everything is sweet - better than good. It has never run so smooth and glide through the RPM's.  

So with this and a whole lot of adrenalin running through the veins from the b/ball game I give it nice boot coming out of the stadium and down the Hwy about 30min. ago. When I hit 1 bar of boost or around 6300rpm all kinds of shit starts happening. Revs are going up and down, power on then off, feels like the rev limiter is kicking in early.. I cant get the car to boost above 1 bar... sounds real shit and feel's like somthing is about to blow up.  

Any ideas??

Easy fix?

Besides that it still drives great up to 1 bar of boost ;)

"See what happens when you play rough with your toys!" (mum... about age 5 or 6)

Sound more like an electrical faults somewhere.

Yeh rip off that kick panel and see what you see:)

With a T78 you hope if its a std ECU it will at least have a workshop sticker on it, or it could be a HKS F-Con or Pfc?!?!?!?!?

Tell you what, the car is gone, perhaps you want to swap for a silver GTST:)

What do you mean by sounds like it is about to blow up, bad miss, or engine drops a few thousand revs????

Yeh rip off that kick panel and see what you see:)  

With a T78 you hope if its a std ECU it will at least have a workshop sticker on it, or it could be a HKS F-Con or Pfc?!?!?!?!?

Tell you what, the car is gone, perhaps you want to swap for a silver GTST:)

What do you mean by sounds like it is about to blow up, bad miss, or engine drops a few thousand revs????

Lots of bad miss's (spelling)

With foot on the gas it does not drop a few thousand just jumps back and forth in the 5500 to 6500 range (like the rev limiter @ 9000 rpm or there abouts... never get a good chance to look at that RPM ;))

might sound obvious, but check for vacuum leaks or hoses that may be blown off :)

sometimes the most obvious solutions are the fix ;)

Might sound obvious... but I have not checked yet and did not think of it- it is dark and I have no good lights to check (no garage for me :D)

I will also check this in the morning along with the ECU (how embarrasing.. after 2 months of having the car)

Thanks for the reply.

Can the car still boost to 0.6 or 0.9 bar if the hose is blown off? Because it's still sweet as up to 1.0bar of boost.

Robin, sounds a bit like plug gap is too wide at that boost. My suggestion, put the exxy plugs in a box and put them away, and get NGK copper 7 heat range and gap to 0.76 - 0.8mm. From your description it sounds like the boost is limiting spark. At worst it could be a coil pack.

Roy

I have a lovely 94 black auto R33GTSt that would love you to do your thing and turn it into a drag queen :D

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • Thanks for the info. The only "Issue" I've had with the shifter is I always found the throw between 4th and 6th gear too close. I'm always worried to shift into 4th accidently and sending my motor to the moon. Adam LZ recently came out with a video and stated Serialnine revised their shifters to correct this and will change all the revised parts for 150$. Strangely enough, I contacted Serialnine right after and they denied it and said it's bullshit. I found that strange as he's a distributer. I'll keep this forum post updated on that saga.
    • Yep that is correct. It allows you to adjust the short throw range from what I can tell
    • Car has been running great, I've put about 300km's of break in time on it. First thing that stands out with properly sealing rings is no more noticeable crankcase smell coming out of my catch can. This may seem insignificant, but the constant smell while driving around was infuriating. It's also nice to see my oil level remain stable. Two new issues have developed that I only noticed this weekend though. There's a very noticeable driveline vibration past 100kmh. I only noticed it now as I've been babying it under 100kmh in the backroads. This comes as no surprise as I'm running a one-piece shaft, and I paid zero attention to my driveshaft angle when I put everything back in. I also have a fair bit of voltage drop on hot starts. The starter audibly is forcing. No issues on cold start though. I must not have removed all the paint under my main block ground during assembly. I'll try and take care of both those issues this week once the kids are asleep.  I also received all the parts I was missing for my direct port setup. I will hopefully have pictures of that up soon. I'm hoping to get back on the dyno the week of June 30th as I'll be on vacation. I'm confident I should be able to make north of 500rwkw on pump gas and WMI. I'll go back again later this summer with E98, but I want to confirm my ethanol content sensor is working properly first. I've never seen it read anything but 11%. This makes sense for our 10% ethanol content pump gas here, but I would expect the occasional movement between fill ups. 
    • 75% complete. Will now need to get a new axle with 5x114.3 hubs and then figure out how to customize some mudguards for it once the wheels are on.
    • Trailer prep is underway... Lined up the wheel to get a rough indication of how it would sit Then removed all the bits (as far as possible) and gave the frame a light sand and quick lick of paint   Then added some carpet
×
×
  • Create New...