Jump to content
SAU Community

4, 6 and rotor nats

Clint32

By Clint32,
in South Australia

 Share

Recommended Posts

9krpm Mentor

9krpm

Posted
Posted
Ask 9KRPM. 280rwkw @ 14psi from his Honda with one of their turbochargers sure isn't bad :) Enjoy Dan!

hahahha you made a mistake finally, it's actually a tad more than 14 psi :wassup: but thank you so much Martin. Hat off to you Martin. I can't wait until you dyno tune it again when my car is ready for more.

If you can get me the skyline diff conversion kit from Con before the drag national I will enter the drag with you and call you king Martin too :P

Willalls have always built the fastest and most reliable Skylines in SA, and Australia for that matter. They build their engines in house, they tune in house. They dont make excuses. They are the best at what they do, and have the runs on the board to prove it. They also do plenty of street level Skyline work. However they wont go around fishing for the $5 job, which is why only the serious players know them. I highly recommend Keir Wilsons facility.

I can vouch for this too. I highly recommend Keir Wilsons facility. One of the nicest team I've fortunately known. I've learn so much from such short time with them. They are real motor enthusiasts and love to look after real enthusiasts. I would also hate to see them waste their time with non serious ppl as they are not a profit orientated workshop.

What does Willall racing do for the average street guy nowdays. Or is it more the topend drag stuff?

my car is a daily drive mate, I may give the drag strip a go but just for fun only ;)

  • Replies 72
  • Created
  • Last Reply

Top Posters In This Topic

Popular Days

Top Posters In This Topic

Popular Days

CheekyR32 Proficient

CheekyR32

Posted
Posted
any one know if keir and john will be racing? few of us thinking about heading over again from Perth to watch.

For John, depends if its ready as always, should be though.

We are coming over to Perth in April for your drag racing BUT have a wedding to go on the actual day that its on... peaking....

9krpm Mentor

9krpm

Posted
Posted
any one know if keir and john will be racing? few of us thinking about heading over again from Perth to watch.

Keir will be there with a couple of nissans :). I hope John can make it too.

It's going to be big guys.

Lets hope we will see some sub 8 sec runs.

whatsisname Grand Master

whatsisname

Posted
Posted
and you too? dont be soft like that nightcrawler guy.

what about whatsisname, haven't seen him on teh forums in AGes!!!

Hey Tim! Yes mate I'm still around. I had the shits with cars for a while there (was doing a LOT of bodyboarding instead - even saw Martin down at Waitpinga... he was fishing and I was getting barrelled :rant: ) but now I'm keen to get back into things again.

I'm planning on entering the 4,6 and Rotary Nationals. Haven't raced the car since the HKS cams went in so it will be as good a reason as any to give it another shot.

It looks like we will have a few entrants... which is good to see :D

Clint, the 32 looks bloody awesome mate! Looking forward to big things from the beast.

Roy Grand Master

Roy

Posted
Posted

So whats the go if you want to enter. I was hoping to go to Mallala, but im not going by myself.

I take it this is heads up racing, so if your sh1t, you will get like 2 practice runs then eliminated in the first round:( ?!?!?!?!

Whats entry worth, entries still open. Who do i speak to to get mroe info. Be good for a laugh and soem fun as long as entry isnt too high...:(

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now
 Share
Go to topic listing


  • Similar Content

  • Latest Posts

    • GTSBoy
      Boost cut after swap(RB25DET NEO) R34

      By GTSBoy · Posted

      Yes. You will need to get the original boost sensor and wire it in. That is.... if you plan to use a stock ECU - even a Nistuned ECU. The Nissan ECU will not operate correctly without it connected. And yes, it will do annoying stuff like you are experiencing. You will almost certainly be better off with some aftermarket ECU, than trying to hunt down rare sensors.
    • Kapr
      Boost cut after swap(RB25DET NEO) R34

      By Kapr · Posted

      Ok so ABS/TCS is "not" the problem. Yeah i know now about the ABS with Nistune(i told that to the Nistune guy) but iam not 100% why or why i dont have ABS. ABS cube is in the engine (always has been) but i had braked couple of times rly hard and brakes just locked and scream. Does all Skylines have ABS cube? That boost sensor https://www.sau.com.au/forums/topic/367633-wtb-r34-gtt-turbo-pressure-sensor-pics-inside/ Is this it? I need to ask but i have a picture of engine bay and i do not see that (100% is not in that place) If i do not have this the car can do what mine is?(cutting around 4000 rpm) Here is the pic of my engine bay(only one i have) BUT i think i dont have that cuz loom was used from my RB20DE NEO and i know (obviously) that it does not have boost control or any wire to that...) so maybe that is the problem? (i dont know for 100% if that car where the engine is from had that)...but i dont have the loom from that
    • MBS206
      S1 rb25/s14 starting problem

      By MBS206 · Posted

      I'm with you here. It's either loom has an issue, OR, injectors are not functioning properly. It could even be they're just constantly dribbling, hence the wet, but not firing.
    • Duncan
      S1 rb25/s14 starting problem

      By Duncan · Posted

      Depending on how long the car sat it is very possible for injectors to be stuck open or closed, I'd get them cleaned and flow tested. Other than that, obviously when the loom changes and the car doesn't start any more....the loom is suspect so some tracing / comparing may be required
    • 25zenki
      S1 rb25/s14 starting problem

      By 25zenki · Posted

      Harness is for a s1 Rb25det, and it is engine and lower harness.  the old harness had broken off plugs and was in very rough condition/exposed wires and splices etc. it is not able to be put back on the car, I could visually inspect to see if they had rewired any pins on the ecu plug. The fuel pump definitly isn’t turning off it’s an external pump and very loud you can hear it. Will look at the other harness tonight, am also going to pull the fuel rail and watch the injectors spray, will update here with what I find. Pretty sure at this point it has to be something to do with injectors because car will fire up on starting fluid and cas is clicking the Injectors. Fuel pressure is steady 43psi 
×
×
  • Create New...