Jump to content
SAU Community

Recommended Posts

I'm planning to upgrade my injectors soonish so I've started to look around now. My current injectors are a little sus, as my fuel tank was rusted to the shithouse and some of that red stuff must have gotten through the fuel filter. Starting is difficult and fuel economy around 14L / 100km.

Getting a nistune in a couple of weeks, and apart from a 3" hiflow exhaust my HCR32 is completly stock, so I was thinking a more modern type of injector with improved atomisation would be better for response and economy, does anyone have opinions on how these ASNU / Bosch injectors compare to the Nismo ones?

http://www.asnuperformance.com.au/

  • Replies 153
  • Created
  • Last Reply

Top Posters In This Topic

Yep, not sure why but GTR injectors just seem to give poor economy from the tuner I spoke to, he said they also commonly leak through the injector body, I know mine did both of these things but I can't comment on the truth of how common it is or why.

  • 2 months later...

Sorry for thread jacking but any opinions on the ASNU1000cc injectors heard they can improve economy.

http://www.asnuperformance.com.au/gallery/High%2BPerformance%2BInjectors/ansu-performance-1000cc-injector/110282

  • 9 months later...

Old thread I know but I have a quick question, Instead of wiring in 6 resistors close to the injector can you not just wire in 1 resistor on the 12v feed before it splits in to 3 then the other 3? Just 2 conections to make instead of 12 or is there something im missing?

As it is batch fire 3 injectors fire at once, so if you multiply the resistance by 3 and use a single resistor it would work imo.

Sorry my bad divide it by 3 as V = I*R so V/I = R so if you have 3x as much current you require 3x less resistance

12/1.2 amps = 10 ohms, as 3 injectors will fire at once you have 3x as much current so 12/3.6 = 3.33 ohms

Obviously the battery is closer to 13v and hence lower amps but the theory is the same however you probably can't buy a 3.33 ohm resistor, to get an equivalent resistance of 3.33 ohms you could run 3x10 ohm resistors in parallel bunched together, be easier to solder in one big lump than putting one on each injector.

Up to you I guess.

  • 2 months later...

What is the nicest way to wire the resistor to the 3 injectors in the sub harness so you can still unplug it from the main harness when pulling the motor out?

I understand that for one injector you could use the existing wiring, but what about the other 2 in the sub harness.

Hope that makes sense

  • 8 months later...

no nistune/ ecu talk... cant even get the ecu in diagnostics mode :dry:

engine does crank, did not start when pump was hard wired, injectors are getting power

am going to install stock injectors again and redo wiring back, isnt the daily so not a big waste

  • 4 years later...

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now



  • Similar Content

  • Latest Posts

    • My guesstimate, with no real numbers to back it up, is it won't effect it greatly at all.its not a huge change in position, and I can't see the air flow changing from in turbulence that much based on distance, and what's in front of it. Johnny and Brad may have some more numbers to share from experience though.
    • Which solenoid? Why was it changed? Again, why was this done? ...well, these wear..but ultimately, why was it changed? Did you reset the idle voltage level after fitment? I'm just a tad confused ~ the flash code doesn't allude to these items being faulty, so in my mind the only reason to change these things, would be some drive-ability issue....and if that's the case, what was the problem? Those questions aside, check if the dropping resistor is OK ...should be 11~14 ohms (TCU doesn't throw a flash code for this) ~ also, these TCU designs have full time power (to keep fault code RAM alive), and I think that'll throw a logic code (as opposed to the 10 hardware codes), if that power is missing (or the ram has gone bad in the TCU, which you can check..but that's another story here perhaps).
    • Question for people who "know stuff" I am looking at doing the new intake like the one in the picture (the pictured is designed for the OEM TB and intake plenum), this design has the filter behind the front bar, but, the filter sits where the OEM duct heads into the front bar, and the standard aperture when the OEM ducting is removed allows the filter to pulled back out of the front bar into the engine bay for servicing, a simple blanking plate is used to seal the aperture behind the filter This will require a 45° silicone hose from the TB, like the alloy pipe that is currently there, to another 45° silicone hose to get a straight run to the aperture in the front bar Question: how will it effect the tune if I move the MAF about 100-150mm forward, the red is around where my MAF is currently, and the green would be where it would end up Like this This is the hole the filter goes through  Ends up like this LOL..Cheers    
    • Despite the level up question, actually I do know what that is....it is a pressure sender wire.  So check out around the oil filter for an oil pressure sender, or maybe fuel pressure near the filter or on the engine. Possibly but less likely coolant pressure sensor because they tend to be combined temp/pressure senders if you have one. Could also be brake pressure (in a brake line somewhere pre ABS) but maybe I'm the only one that has that on a skyline.
    • Pull codes via the self-diagnosis procedure. As far as I can tell this is just a sign of transmission issues but not a code unto itself.
×
×
  • Create New...