Jump to content
SAU Community

D1GP Game Out In Japan


ChaserV
 Share

Recommended Posts

  • Replies 42
  • Created
  • Last Reply

Top Posters In This Topic

nah, you dont need an NTSC TV...

generally with an PS2 or xbox game, if you have a chip, will work fine, just some of the intro videos may trip out.

yeah thats if you want to chip your box though. id still like to keep my warranty:D:D

that sites awsome!! bloody good prices...has anyone ordered from them, how long does it take to arrive in aust?

Link to comment
Share on other sites

Ok just to clear some stuff up for everyone There is going to be "NO Realsed Outside of Japan"

just like the Initial D game for the ps2 it was only realsed in japan and there was no english version, sadly it will be the same for D1 GP, i will have this game by 2morrow night, i am half-way through getting it at the moment, it should be good.

Ohh yeah and it was realsed or the Leaked rls was 17/02/05 D1_Grand_Prix_JPN_PS2DVD-Caravan

Link to comment
Share on other sites

my friend got back from japan last night and bought this back with him, ive been playing it all afternoon. :cheers:

its pretty hard at the start, you have to do a licence test to compete in d1, licence will take abut 3 damn hours, but teaches the basics of drift... the d1 competition is fierce, I got to a final and had 3 tie breakers where me and the computer oponent,

I then crashed on the next pass. god damn it >_<

Link to comment
Share on other sites

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now
 Share




  • Similar Content

  • Latest Posts

    • Got some decent progress after work yesterday and also today. Got the ECU all wired and passenger side interior all back together. Kept the wiring up nice and high to avoid people standing on it. Got the surge tank relays rewired and tidied up the pump wiring and cut a hole to bring the cables through.  I found a spare USB cable I had lying around so I decided to cut it up and see if I could use it for my CAN 1 bus. Turned out one of the pins I needed was to the shield of the cable so i cut it up and desoldered it and resoldered to the correct pins.  Had the issue with the powersteering hose hitting the A/C compressor and fan shroud. I pulled the bracket off and modified it to remove the front mounting point which now clears it all. Will keep an eye on it to see if theres any signs of fouling once it's up and running.
    • That's some good input mate. Nice.
    • So today I went well outside my comfort zone (again) to replace my valve cover gasket.  I have had a big leak over the exhaust leading to a lot of smoke and smell every time I drove it. The leak was in the rear driver's corner.  The job wasn't hard as such, just a bit finicky and time consuming.  The old gasket was rock hard and broken right where the leak was.  The leaky corner had so much sitting oil in it.  The good news to my amateur eyes was no buildup or sludge under the cover. It all looked fairly nice in there.   I haven't started it yet. I ran out of light and body when putting the coils and injector loom back in. Probs only 30min left for the morning.  I was so nervous putting the cover back on, I must have lifted it 5 times to make sure the gasket was still seated properly. God it's going to be nice to be leak free and not make other traffic light queuers think my car is about to explode.
    • Gave the Mazda it's first wash, it will need some clay, a light compound, and polish polish to remove a few swirl marks, but that will be a job for when I have a full day to get my DA polisher action on
    • Just did this job on my 32 with the boost doc kit. was quite simple to fit, hardest part was getting the rubber bungs back on the firewall. does anyone know how the heater will work now without the flap in the bend? Will I just have a heater on 24/7 now?
×
×
  • Create New...