Jump to content
SAU Community

Recommended Posts

  • Replies 102
  • Created
  • Last Reply

Top Posters In This Topic

And will Ben crack a 1.15s lap???? Only if he's not weak sauce (j/k!)

With a Club Championship round the following week at Winton I will probably give this a miss - but will come down and watch however.

The PIARC Sprint is on the same day:( I have to say id rather go back and have a crack at Phillip Island then Sandown for what will most likely be my lat Vic trackday:(

Anyone knwo when there is another Sandown day, perhaps late April, hell late March?

  • 2 weeks later...

I want to do PI, but its closer/cheaper to do Sandown. So will be sending my applciation in on the weekend. Plus i havetn been there and its the track i most wanted to do when i first got to vic.

I suppose i can do the Saturday at PI then the Sunday at Sandown, will have to seee how funds look:(

I want to do PI, but its closer/cheaper to do Sandown. So will be sending  my applciation in on the weekend. Plus i havetn been there and its the track i most wanted to do when i first got to vic.

I suppose i can do the Saturday at PI then the Sunday at Sandown, will have to seee how funds look:(

ooh yeah :D :D

Sounds like a plan, will have to wait and see, apparantly if you withdraw then you dont have a say in who tsakes your place. There is a waiting list and those that are on it get first dibs:(

Should know tomorrow. If i cant do both days then i might just go back to Sydney for the weekend since work will be paying.

Guest
This topic is now closed to further replies.



  • Similar Content

  • Latest Posts

    • Ah! I actually managed to snag a lightly used set.... that aren't so suitable for me right now. They don't work on a GTT without some cutting or creative heat moulding. I thought about reselling them myself cause I didn't want to murder them, but it looks like I'm probably going to attempt to murder them/melt them because I may as well. @GTSBoy @PranK can somebody close this thread?
    • Hey mate,  I have a set, one is slightly damaged but wont be noticable once installed.  Shoot me a message if your still after them 
    • I couldn't wait But, the black constant tension hose clamps were too thick and there wasn't enough clearance at the T/B and I couldn't get it to seat properly, so I had use a silver one there I also added some 3" silicone over the alloy bit that goes through to hole on the radiator support as it looked like it was sitting on the edge of the hole in the radiator support, I never noticed a rattle or anything, but there was a witness mark It is basicly done, and I can live with the silver hose clamp at the T/B, I will get a black clamp for the head vent though where it is attached to the bulkhead fitting  It never stops...LOL, only issue now with the shock tower brace is it slightly touches the under bonnet liner now, if I leave it it will either wear some paint off the brace where it touches, or damage the liner, so I removed the liner to see what I have to work with, with the liner removed I have about 20mm of clearance, but sadly the middle part of the underside of the bonnet is only dusted with paint and looks crap, so I cannot have that, but.... as I have a roll of Carbuilders premium under bonnet insulation in the garage laying around that is only 5.5mm thick (we were going to use it on the boys Patrol, but he crashed the front of it a few months and it was written off, hence why he now drives my old Honda Accord Euro), I'll use the OEM liner as a template and get the Carbuilders stuff fitted up to cover that dusted paint up
    • You have a knack for photography my friend. It makes the 86 look like a complete bucket. The 34 went with you to Europe and back. It's special. (we all feel the same about our 'shitboxes' that every bystander seems to absolutely love)
×
×
  • Create New...