Jump to content
SAU Community

Recommended Posts

aww my baby wont start , battery is all good when i turn the key to start it, makes a loud fast clicking sound

plz help :rofl: argh wats the problem, and how much am i looking at to fix it? or is there a cheap and easy way to fix without a mechanic :(?

Link to comment
https://www.sau.com.au/forums/topic/68344-car-wont-start/
Share on other sites

As everyone else has said, it's prob your battery. I had the same thing two weeks ago. If the batt has gone flat, you're probably looking at buying a new one, rather than trying to charge it and stick with the old one. I tried twice then bit the bullet.

It takes around 20+mins of driving to charge enough to start the car again.

To answer your q, the battery doesn't have enough charge to turn the starter motor. It is a cheap fix. Replace it with a batt that has 450+CCA if you can. Your starter motor is fine. :rofl:

Mark

edit: Sumo's thoughts are it isn't the injectors. The rationale makes sense to me. The battery is still the prob though.

Link to comment
https://www.sau.com.au/forums/topic/68344-car-wont-start/#findComment-1268340
Share on other sites

Fast clicking sound will be the starter motor solenoid trying to pull in. Have heard it plenty of times. The breakdown comes when it bridges the motor contacts and the bat doesn't have enough charge to spin it so it releases, Then pulls back in and so forth.

Cheers

Sumo

Link to comment
https://www.sau.com.au/forums/topic/68344-car-wont-start/#findComment-1268964
Share on other sites

It's basically a problem of voltage to the solenoid (not necessarily a battery problem, though).

Install a relay between the battery and the solenoid. Use the existing wire onto the solenoid to switch the relay, so that the relay supplies direct battery power to the solenoid.

Link to comment
https://www.sau.com.au/forums/topic/68344-car-wont-start/#findComment-1272889
Share on other sites

it's the battery.

Here's how to test.

Get a multimeter and a mate

Put multimeter on battery to check voltage

chance are you will get...12 volts, so you will say "SEE it's not the battery"

but then...get your mate to turn the engine over, if the voltage drops below 8v, your battery is cactus, take it to a battery shop and they will test it for you to be sure.....If the voltage holds at 10v+ then it is probably not ya battery, in which case...umm only think i can think of is you could tap the starter motor/solenoid, sometimes they jam up....

Link to comment
https://www.sau.com.au/forums/topic/68344-car-wont-start/#findComment-1272982
Share on other sites

Yeah, I wouldn't give up on the battery totally. I thought my battery was stuffed. Car had been off the road for 6 months and was completely dead when I went to crank the car. Stuck it on charge for like 18 hours and it started no problems. Drove it to the mechanics for rego., he managed to drain it completely, and said he reckoned it was stuffed. Had to jump it twice on the way home, whacked it on the charger again, cleaned the terminals and connections, and hey presto, no more problems. Like you suggested, if its still running the radio etc. it must still have some charge. From my experience with batteries, the big killers seem to be age, and running run them dead flat, then leaving it flat. If your battery is more than a few years old, its the easiest thing to change first when chasing this kind of problem.

Hope this helps,

machg

Link to comment
https://www.sau.com.au/forums/topic/68344-car-wont-start/#findComment-1272986
Share on other sites

oh, and if it is your battery like I assume, jumper cables will *most likely* NOT help. You will also need some decent (fat) jumper cables that can pull heaps of current.

I havn't tired clutch starting one with these symptoms, but seriously, just take the battery to battery world and have it tested, I am quite confident it is the problem. And it's an absolute prick of a problem that had me stumped cause it had the 12v and like u say, stereo etc works great.

Way I found out was rang a mate that works for NRMA, I was trying to find imobilisers etc etc, and he was like "it's the battery" seen it happen to more cars since (mine did it on saturday)

Link to comment
https://www.sau.com.au/forums/topic/68344-car-wont-start/#findComment-1272994
Share on other sites

ive had heaps of problems and delays with batteries. jumping from another car just made things worse for me, as it ran down that car battery too.

i ended up on just buying a cheap ($15) charger, and i woudnt reccomend it, it gave me grief for several days. at first the charge indicator (4 LEDs) worked, but then they just stopeed working, but it seemed to still be charging the battery, as it was hot and humming. several days later it still hadnt chrged it, so i swapped the battery for a tiny one i had lying around. left it on overnight and it charged it up enough to start it.

if you want to charge it, its a good idea, but dont buy a cheap charger, there crap (my one was, other ones might work) spend some extra money, and keep it for if you have this problem again! the good ones start at about 60. new batteries cost about that much, depending on where you get them.

im just so sick of batteries. they just piss me off! i had problems for months!

Link to comment
https://www.sau.com.au/forums/topic/68344-car-wont-start/#findComment-1278902
Share on other sites

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • Ok thanks..that was my second question if i can somehow bypass this even with Nistune(that is all i have right now...aparat from stock ECU. So with some aftemarket it can by "bypassed" or make it work?  I know there is Link or Haltech (mainly used). We have ECUmaster here so i will gather some info about it.
    • Yes. You will need to get the original boost sensor and wire it in. That is.... if you plan to use a stock ECU - even a Nistuned ECU. The Nissan ECU will not operate correctly without it connected. And yes, it will do annoying stuff like you are experiencing. You will almost certainly be better off with some aftermarket ECU, than trying to hunt down rare sensors.
    • Ok so ABS/TCS is "not" the problem. Yeah i know now about the ABS with Nistune(i told that to the Nistune guy) but iam not 100% why or why i dont have ABS. ABS cube is in the engine (always has been) but i had braked couple of times rly hard and brakes just locked and scream. Does all Skylines have ABS cube? That boost sensor https://www.sau.com.au/forums/topic/367633-wtb-r34-gtt-turbo-pressure-sensor-pics-inside/ Is this it? I need to ask but i have a picture of engine bay and i do not see that (100% is not in that place) If i do not have this the car can do what mine is?(cutting around 4000 rpm) Here is the pic of my engine bay(only one i have) BUT i think i dont have that cuz loom was used from my RB20DE NEO and i know (obviously) that it does not have boost control or any wire to that...) so maybe that is the problem? (i dont know for 100% if that car where the engine is from had that)...but i dont have the loom from that
    • I'm with you here. It's either loom has an issue, OR, injectors are not functioning properly. It could even be they're just constantly dribbling, hence the wet, but not firing.
    • Depending on how long the car sat it is very possible for injectors to be stuck open or closed, I'd get them cleaned and flow tested. Other than that, obviously when the loom changes and the car doesn't start any more....the loom is suspect so some tracing / comparing may be required
×
×
  • Create New...