Jump to content
SAU Community

Recommended Posts

Well I've just pulled the turbo off my GTT which is 7/99 series one and put it next to one from an R33 series one.

First thing is that on the side of the compressor covers the R33 one has 45 v 1 whereas the R34 one has 45 v 4 on it.

The compressor covers appear identical.

Now I know this goes contrary to popular opinion but the R34 compressor wheel appears to be metal just like the R33 one.

On the R33 compressor side outlet there is a 1 cast on the outside and a 3 printed on the inside. On the R34 these are both 2's.

On the exhaust housing on the r33 one is cast 307B 2IU, a bit further round there is an 8.. The equivalent on the R34 one is 527A OP6 and further round a 9.

On the other side of the exhaust housing we have F 2IU (R33) and E OP6 (R34).

One thing that is definitely noticable but a bit hard to measure is that the R34 exhaust housing is bigger than the other one. Also the entry port from the manifold is wider on the R34 by about 1mm or so in both directions.

Anyway, I just thought I'd post this for general information. Perhaps people can add their knowledge to it. Maybe if someone has an R33 series 2 turbo or R32 one off the car in front of them they could post the equivalent details.

post-7957-1151318629.jpg

post-7957-1151318643.jpg

Search words : identify R33 R34 NEO turbo difference 45v1 45v2 45v3 45v4

What kind of sound does it make when you tap it with your fingernail?

I had assumed my R34 turbo was plastic/nylon/whatever till I did this and it sounded tinny so I dug out the old one to check and they seem to be the same. They also look the same as the pic you have posted.

Hmm, What does yours say, 45v????

Yeah, we should link this to the Stock Boost for R34 thread. The R34 compressor wheel is nylon plastic crap and isnt as strong as the 33.

But as I also mentioned, some series 2's came with a steel wheel but, as soon as i find solid evidence, ill post.

Hmm, it's looking like the other turbo I have is series 2 R33. Can one of you R33 owners look at that link I posted above and tell if the car is series one or two. That's the car this turbo came from.

Anyone want to post a pic of the turbo side on so we can see the size of the exhaust housing?

This 45v1.2.3. thing is weird.

Abo i'm 95% sure that's a SII R33.

* Bonnet lips down over the center grill.

* Headlights (im pretty sure on this part).

* The panel at the rear between the bottom of the boot and the top-middle of the bumper (S1 is a clear plastic from memory).

  • 4 months later...

Series 1, S2, S3 GTT use different turbo

"14411-AA100"

s1 is nylon plastic with single blade

post-1812-1124278430.jpg

"14411-AA110"

s2 is metal with twin blade, same size as s1

post-1812-1124278548.jpgpost-1812-1124278746.jpg

"14411-AB000"

s3 is metal with twin blade, made by garrett instead of nissan, bigger than s2

post-1812-1124278846.jpgpost-1812-1124278960.jpg

basicly, If your NEO engine cover W/O RED wording...that's S2 or S3

more detail about difference between s1,2,3 (japanese)

http://2style.net/r34sedan/hikaku/hikakutop.htm

Edited by Maxx

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now



  • Similar Content

  • Latest Posts

    • The sodium acetate, mixed with citric acid, doesn't actually buffer each other. Interestingly though, if you used Sodium Acetate, and acetic acid, THAT becomes a buffer solution. Additionally, a weak acid that can attack a metal, is still a weak acid that can attack a metal. If you don't neutralise it, and wash it off, it's going to be able to keep attacking. It works the same way when battery acid dries, get that stuff somewhere, and then it gets wet, and off it goes again breaking things down. There's a reason why people prefer a weak acid, and it's because they want TIME to be able to be on their side. IE, DIY guys are happy to leave some mild steel in vinegar for 24 hours to get mill scale off. However, if you want to do it chemically in industry, you grab the muriatic acid. If you want to do it quicker at home, go for the acetic acid if you don't want muriatic around. At the end of the day, look at the above thumbnail, as it proves what I said in the earlier post, you can clean that fuel tank up all you want with the solution, but the rust that has now been removed was once the metal of the fuel tank. So how thin in spots is your fuel tank getting? If the magazine on the left, is the actual same magazine as on the right, you'll notice it even introduces more holes... Well, rust removal in general actually does that. The fuel tank isn't very thick. So, I'll state again, look to replace the tank, replace the fuel hanger, and pump, work out how the rust and shit is making it past the fuel filter, and getting into the injectors. That is the real problem. If the fuel filter were doing its job, the injectors wouldn't be blocked.
    • Despite having minimal clothing because of the hot weather right now, I did have rubber gloves and safety glasses on just in-case for most of the time. Yes, I was scrubbing with my gloves on before, but brushing with a brush removes the remaining rust. To neutralize, I was thinking distilled water and baking soda, or do you think that would be overkill?
    • You can probably scrub the rust with a toothbrush or something. After you get the rust off flush well with water to neutralize and you will probably want to also use a fuel tank sealer to keep it from rusting again.
    • The sodium citrate solution is designed to buffer the citric acid to keep it from attacking metal quite so much, the guy that came up with that recipe did a ton of testing on how much metal loss occurs over time and it's nothing crazy unless you forget about it for months:   
    • Ohhh I see lol To be honest the main reason why I wanted to start modding is because of a business trip to Japan and Indonesia. I saw many cool and modded cars all throughout in these countries, especially Japan. I myself am of Chinese+Japanese nationality and when living in china (never lived in Japan js my dad side lol) I remember staring at these cars pass by with their loud tacky exhausts and insane wide body kits. And when I went back to Japan, I got even more invested even asking people about their cars and why they modded. Most gave similar answers to what you said but funny enough one guy just said that he saw the need for speed movie being filmed once in Tokyo I think near Shibuya Crossing and got inspired to tune and mod. After that I just started to fantasize on owning a car like that. Also tbh I prefer the R32 over the R34 it's just the R34 is more iconic lol (also apparently better aftermarket support than the R32) and my only goal really is just to make the car mine and make it fun to drive. As much as I love my Cayenne it's pretty bland to drive. Sure the interior is nice and pretty, gives you attention yada yada but I've wanted to experience what it is like to have a car that is truly yours. I suppose thats the goal so far. Haha if you find where I'm from, then sure. Ill help you out on your next "financial decision"
×
×
  • Create New...