Jump to content
SAU Community

Recommended Posts

What would in your opinon be the cheapest way to build a 10 second car.

The only rules are:

- Cost of the 10 second car must substitute in the cost of the car and the mods.

- No major weight reduction mods

- No blown carburettored V8's

In my opinon I believe the GSR Lancer would be the best candidate for building a 10 second car as its a relatively cheap car to buy, 4wd and has an abundance of aftermarket kits to build on it.

Link to comment
https://www.sau.com.au/forums/topic/76558-cheapest-10-second-car/
Share on other sites

Old mazda 808 with a 13BT and old school T04, microtech, shortened 9inch, supra 5 speed and custom tailshaft with 8 inch slicks jammed under the rear end with some suspension work.

Total cost would be about 17k including car

Old mazda 808 with a 13BT and old school T04, microtech, shortened 9inch, supra 5 speed and custom tailshaft with 8 inch slicks jammed under the rear end with some suspension work.

Total cost would be about 17k including car

I am up with that for sure the cheapest way to build 10sec package is just the way hes said, but put a T66 (with large exaust wheel) on instead of the T04

Mate is almost finished with his 13bt in 1300 wagon with the large port work and the T66 i cant wait till its run in and i get to have a go

I know you mentioned no blown v8s but the cheapest is definately a vb or vc commodore.

-THe car= $1000 in pretty good cond

- Motor= $4000 308 with a stroker at least 355

- Tranny=$3000 tricked up manualised auto

-Diff= $2500 9 inch with 4 link setup

- Wheels/tyres and miscalaneous= $2500

All up $13000

ANd if you want to go injected, add another 2g.

But rotary was my second choice its just the base cars are worth alot these days!!!

yea i knew a guy with a rx2 with a 13b in it it wooda been near 10s and it was cheap for him motor was 6k worked off its tits then shell was just about nothing nothing

then he got a r100 and put the motor in that

other guy i know has a V8 in a Ford Capri its a ex drag car does 11's had huges wheels on the back and motor coming out the hood

if he superchargers it it will do 10's

Go the rotor in a lite car :cheers:

The other cheapish one would be a 1GGTE with a big turbo, good tune, in something small. The stock bottom ends are unreal. To get a bit more go out of them use a supercharged bottom end, as they are 0.5 compression ratio higher, and can still cop massive amounts of abuse. Full motor would be about $700-1000ish now?

But yeah, carby V8, cheap as, or Rotor. 10sec car isnt that hard, but a reliable street driveable one is a bit more of a trick.

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • I thought it could be an issue because the standard plate was flexing when stressed. Maybe the original gear set will hold a bit better without flex? Last time on the dyno it made around 670nm at the hubs. Now it have bigger turbo and better intake but have not been on a dyno yet. The car is being used from family trips to drag race events. So the shifts can be a little violent. It is grinding if I shift to fast so was thinking I should overhaul it soon.
    • From the factory on RB26s there's a fitting on the intake manifold collector/"plenum" that provides pre-throttle boost signal. That's how they did it back in the day, I figure it's fine to replicate it.
    • I would be surprised if that wasn't the issue. It's probably telling you, that even if you remove the plastic liner, you may have some other clearance issues that may occur too in some scenarios. IE, tyre to guard. It looks like someone has already rolled the lip, but you may still have issues in the future IE, turning and hitting a bump etc. The fact it changes how bad it makes the noise when you are going backward vs forward is highly indicative that it's the tyre rubbing. They do make a terrible sound, even if you're only pushing a project car that has a liner hanging down on a tyre!   Has the car been lowered? If it has been, what is the measurement from the centre of the wheel hub to the lip of the guard straight up?
    • Summernats cruiser?
    • Mark's a bit smarter than people give him credit... He'd convince the person that is to become dead, to drive him to the forest first. That way his car has no evidence in it, and he's free to dispose of their vehicle permanently how he sees fit too...
×
×
  • Create New...