Jump to content
SAU Community

Recommended Posts

If you're trying to save money, trading in your non turbo Skyline for a turbo Pulsar may not really change your Total Cost of Ownership, especially if you're going to modify it.

Turbos (especially the GTiR, which has a reputation for overheating) need a lot more TLC than a NA car.

If you're trying to save money, trading in your non turbo Skyline for a turbo Pulsar may not really change your Total Cost of Ownership, especially if you're going to modify it.

Turbos (especially the GTiR, which has a reputation for overheating) need a lot more TLC than a NA car.

Sorry, im not intending to buy the GTiR just yet. Im selling my skyline to finish off paying my car loan cuz i hate the interest rates. By saving on the interest rates (12%), i'll have enough money to buy a GTiR within six to eight months. By then my financials will all be soughted out, i just dont want to get a bad credit rating should i ever get so bad that i default on my loan.

dude pocket rockets go off, you can make them look good just like any car, just dont go OVER the top with cosmetics and it'll end up lookin' classy and not like somethin off a st corner in st kilda lol.

the bonnet is hideous and the rear looks very plain...

good motor ... glass gear box ... ugly styling ... performance potential ...

if you dont mind spending a bit of money to get her up and going nice as well as looking nice ... buy one. Otherwise just buy a n14 SSS or sumfink <---- they look ok and are fairly cheap on fuel, good luck finding one with low k's on it however!!!

seems to me your stuck between a rock and hard place ...

GTI-Rs are a great car. I had one for two years. a lot of the problems people mentioned are now not so bad. there are plenty of off the shelf performance parts for them now as they are much more popular than they were 2 or 3 years ago. in the two years I had mine it saw plenty of 7000rpm launches and never had a clutch or gearbox problem. also dragged it at WSID once and went to a few track days. I spent a fair bit of dough on the brakes and suspension as they go very hard stock but don't stop and turn so well. with some mods on brakes and suspension though it will be a very nice package. then spend a bit on power upgrades and it will be damn hard to beat.

don't expect it to be cheap, because the fact is it's AWD, and turbo. those two things tend to bump up associated running costs on any model.

very fun car to drive though, and a much better SR20 than found in silvias etc (ie. solid lifters, longer duration/higher lift cams, 440cc injectors, bigger turbo, quad throttles, 19mm conrod bearings and on and on.)

if that is what you have wanted i say go for it.

two words

Plough Understeer

Generally followed by snap oversteer. Not a good handling trait in anyones books.

Even with the white line suspension works package it will still tend to understeer and snap, it's just a little more controllable......

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • I don't know for sure, but I'd expect them all to be interchangeable given the diff end and hub end don't move/change between any C34 series. Often Nissan will change part numbers and the aftermarket follows those year ranges; but the original part number change doesn't mean other parts won't fit. The change could be a change in material, internal parts or even just supplier. For example, all the RB gearbox to engine bolts are no longer available and there is a new part number instead. The only change is they went from cadmium plated bolts to zinc plated due to the issues manufacturing with Cadmium. They look different but work the same.
    • One year is a bit concerning. Did you try contacting GSP? It says 5 year warranty on the box if I remember correctly. I'm also running their driveshafts on my S2 Stagea.   You could check the part numbers on Amayama for your year. Here's the link for my 1998 which gives the 39100-23U60 part number. Well, that and 39100-23U70. https://www.amayama.com/en/genuine-catalogs/epc/nissan-japan/stagea/wgnc34/6649-rb25det/trans/391 What does it say for yours?
    • I ordered a GSP Front R/H Axle from here - https://justjap.com/products/gsp-premium-front-driveshaft-r-h-nissan-r32-r33-r34-skyline-gtr-stagea-4wd#description It lasted around a year before one of the boots blew out. I'm lowered, but I have GKTech roll center adjusters. One year seems a little premature. I think I'm going to spend the extra money on an OEM cv axle this time. This website - https://tfaspeed.com/collections/nissan-stagea-wgnc34-x-four-parts/products/nissan-stagea-awc34-260rs-rb26-right-front-axle-drive-assembly Makes it sound like the readily available OEM CV axle will only fit 11.1999 Stagea and up (mine is a 2.1997 S1). The JustJap listing didn't mention any years or anything for the GSP axle. Amayama shows '11.1999' and up as well for that part number. As well as 'plastic boot type'. See attached picture. So I guess my question is, does that axle (39100-23U60) really only fit S2 Stagea? It's the front driver side. If it does, I'd love to buy that instead of rolling the dice on another GSP. I've found that OEM one cheaper here: https://www.partsfornissans.com/oem-parts/nismo-jdm-r32-r33-r34-skyline-gtr-r32-gts4-right-front-axle-3910023u60 and here https://www.nissanparts.cc/oem-parts/nismo-shaft-ft-drive-3910023u60 Just a little confused because the JapSpeed listing for the GSP front driver axle doesn't mention any specific years or anything and it fit my S1 Stagea fine. So will 39100-23U60 fit my S1 Stagea even though technically it says '11.1999' and up? What would have changed? Thanks.  
    • Thanks for the info. The only "Issue" I've had with the shifter is I always found the throw between 4th and 6th gear too close. I'm always worried to shift into 4th accidently and sending my motor to the moon. Adam LZ recently came out with a video and stated Serialnine revised their shifters to correct this and will change all the revised parts for 150$. Strangely enough, I contacted Serialnine right after and they denied it and said it's bullshit. I found that strange as he's a distributer. I'll keep this forum post updated on that saga.
    • Yep that is correct. It allows you to adjust the short throw range from what I can tell
×
×
  • Create New...