Jump to content
SAU Community

Recommended Posts

  • Replies 214
  • Created
  • Last Reply

Top Posters In This Topic

True, but if you do a B4 engine swap then you'll have a nice low-end and a free top end, but with a crap mid-range.

Unless you're willing to spend the time and money setting up and tuning your twin turbo setup properly, you're going to hit a nasty flatspot at the point the two turbos change over.

Even if you do, you add a lot of complexity to your setup. If something goes wrong, you're going to have a hell of a job trying to figure out what's failed.

In the end, I'd much rather a EJ20 with a 2.2 stroker kit and a well-matched single turbo. Not as inherently weak as the EJ25 that everyone else has mentioned, but still more torque and better flow characteristics than the stock setup.

Agree with you about the sequential turbos. The B4 has the well-documented "Vally of Death". Check out a typical B4 dyno plot to see what I mean. Sequentials are bloody hard to set up and quite often when people do some serious mods they are the first thing that goes in the bin. The sequentials on the S6 RX-7 are a good example of this.

I think Subaru agree as well as they chose to dump the twins and go to a single, well-sized twin-scroll turbo with the GT.

If I were building a really tough engine I'd go for a 2.2 but rather than a stroked 2 litre I'd go for the 2.2 fitted to the US-spec Legacy Turbo. This thing is basically the same block as fitted to the 22B so it's fully closed-deck with very strong internals and it doesn't have the rod ratio problems which limit revs as the stroked 2L 2.2 setup does. Interesting is that these engines have got piston oil squirters but these were deleted for the 22B.

...Ben

A mate owns a B4, has had a few things done like ecu remap to try and minimize the flat spot. Have looked at the dyno charts and it is still there - just more power all round. Funny thing is in stock form he had to get the engine rebuilt after just 10,000 k's - big end bearing. The guy at Subaru docklands said he was under the impression that they had not been de-tuned very well for our fuel. Also had to get the gearbox rebuilt after smashing a syncro not too long after that.

Other mate has a 98 WRX - 40,000 k's following a decent track day out at winton saw a gudgeon pin fail - out came the engine for a full rebuild, also got the gearbox and clutch done at the same time. He does drive it pretty hard, and John Bowe gave it a good fang around the track that day - but once again not good news for suby warranty claims dept.

Still love the rexies, but I am way happier with the over engineered gtr in the driveway.

so lets see here...

you want...

no lag

good off boost driveability

ability to run a large turbo

no gearbox problems

not too expensive?

hmmmm..

rb30det seems the way to go.

it's the answer to every performance question on this forum.

Q)how do I get more power from my R32 gtst?

A)RB30det

Q)How do I beat a (insert any performance car here)

A)RB30det.

Q)How do I have heaps of power without more lag?

A)RB30det.

Q)Will my R33 gtst beat a wrx?

A)with an RB30det it will.

Q)How do we end this thread?

A) RB30det.

Q)How do I get an RB30det?

A)RB30det.. I mean http://www.skylinesaustralia.com/forums/sh...ead.php?t=15420

I like "but in the wet" comments.. how often does it really rain? well where I am sitting maybe 1 in 10 days.. rest of the time the road is pretty much dry and its never an issue. And when it is raining, its not that hard to drive a tad more relaxed. If I had a rex, I woudln't be pushing it in the wet, even if it did handle like it was dry.

Maybe why WRX are so much more popular in melbourne and sydney than here :rofl:

Agree with you about the sequential turbos. The B4 has the well-documented "Vally of Death". Check out a typical B4 dyno plot to see what I mean. Sequentials are bloody hard to set up and quite often when people do some serious mods they are the first thing that goes in the bin. The sequentials on the S6 RX-7 are a good example of this.

I'm not sure what the S6 RX-7's power delivery is like (hence why I said nothing) but I know that, with the tangled mess of pipes that it does use, when something breaks it's an adventure to try and figure out at which point you've had mechanical failure.

Having a single turbo is simpler, so its usually easier to setup and maintain and more reliable. Even if you're talking engines with parallel turbos (RB26, 2JZ come to mind) at a certain "seriousness point" they get ditched in favour of the big single.

While a part of this is increased flow, if you're going to cause major stress on a lot of components by pumping out a lot more power than the factory intended, its a lot easier to do it and keep it all together if there's only 1 of everything.

hmmmm..

rb30det seems the way to go.

it's the answer to every performance question on this forum.

Reminds me of this quote from The Simpsons:

Troy:  Now, turn to the next problem.  If you have three Pepsis and drink one, how much more refreshed are you?  You, the redhead in the Chicago school system?

Girl [her face appears picture-in-picture]:  Pepsi?

Troy:  Partial credit!

I like "but in the wet" comments.. how often does it really rain? well where I am sitting maybe 1 in 10 days.. rest of the time the road is pretty much dry and its never an issue. And when it is raining, its not that hard to drive a tad more relaxed. If I had a rex, I woudln't be pushing it in the wet, even if it did handle like it was dry.  

Maybe why WRX are so much more popular in melbourne and sydney than here :)

He says after the GC floods!

so lets see here...

you want...

no lag

good off boost driveability

ability to run a large turbo

no gearbox problems

not too expensive?

hmmmm..

rb30det seems the way to go.

it's the answer to every performance question on this forum.

Q)how do I get more power from my R32 gtst?  

A)RB30det

Q)How do I beat a (insert any performance car here)

A)RB30det.

Q)How do I have heaps of power without more lag?

A)RB30det.

Q)Will my R33 gtst beat a wrx?

A)with an RB30det it will.

Q)How do we end this thread?

A) RB30det.

Q)How do I get an RB30det?

A)RB30det.. I mean  http://www.skylinesaustralia.com/forums/sh...ead.php?t=15420

Q)How to get uncontrolable wheel spin in your manually equiped car?

A)RB30det

:):D:D

I'm not sure what the S6 RX-7's power delivery is like (hence why I said nothing) but I know that, with the tangled mess of pipes that it does use, when something breaks it's an adventure to try and figure out at which point you've had mechanical failure.

Having a single turbo is simpler, so its usually easier to setup and maintain and more reliable. Even if you're talking engines with parallel turbos (RB26, 2JZ come to mind) at a certain "seriousness point" they get ditched in favour of the big single.

While a part of this is increased flow, if you're going to cause major stress on a lot of components by pumping out a lot more power than the factory intended, its a lot easier to do it and keep it all together if there's only 1 of everything.

I hear that swapping to a single turbo from the sequential setup on the S6 RX7 saves you about 25 kg! Isn't the 2JZ sequential as well, while the 1JZ is parallel?

Q)How to get uncontrolable wheel spin in your manually equiped car?

A)RB30det

:):D:D

hahahahaha

you must be one of those poor disabled people who can't control pressure with their right foot.

:P :uh-huh:

therefore, what you need is an RB20det equiped car.

then you can flatten your foot to the floor all you want and wait for the power to come on..

hahahahah

*just waiting for Roy to come and yell at me..*

to those that saying rexies aren't laggy read this. This is about the sti. I found the standard rex to be a mild dose of what they are talking about with the sti.

I'm sure a VS v6 commodore would have more low end grunt (i.e. from 1000-3000rpm) than both the gtst and the wrx. I like the r33 because it has reasonable low end but the mid to top end is relly good. v6 commodore gets very rough. WRX no low end at all. Sti even worse. How did you like the way I managed to throw a commonhore in the mix?

http://autospeed.drive.com.au/cms/A_1463/a...?popularArticle

I've gotta agree the stock STi is a pretty hideous thing. Waiting for boost to come on does give you a good opportunity to make a few phone calls and catch up with paperwork though. :)

I guess that's what happens when you've gotta homologate a turbo for Group N. On the flip side you don't have to replace it until you're upping the ante quite a bit. An exhaust and a retune makes the world of difference to boost threshold but underneath it all it's a low-compression 2l engine which is always going to be sluggish off boost. I expect that an RB25 will feel much quicker in traffic.

...Ben

EDIT: Love the Commonwhore reference. My work ute has the V6 and it would make a great boat anchor. I read a thread on Street Commodores forum where they were trying to get a V6 into the 11s on a budget. Sounds like trying to polish a turd to me.

Hey Ben, i think they actually got that shitty vn commie into the 11's!

As for lag. my rex with the standard turbo and tb exhaust could reach 17 psi by 2500 rpm, is that laggy?

I've owned and driven numerous WRX's in very different states of tune, but I have never seen one make 17psi under 3000 rpm.

What mods do you have?

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now



  • Similar Content

  • Latest Posts

    • Haha, i kow right? Could have bought so many cars for the same amount of money (or less) but driving Unicorn gives you at least +1mln to style 😅. Like wise man said "life's to short to drink cheap wine and drive boring cars" 😉
    • Newbie here, proud owner of an Autech 260RS. I'm on the hunt for wiring diagrams specific to the 260RS, particularly S1. I've ran my eyes through R33, R34 Diagrams, there are some similarities, however continue to find incorrect wire colours and pins on connectors in the 33,34 diagrams.   I was hoping someone could point me in the right direction? I'd be happy to pay for the originals in Japanese. I can translate them, at least they would be accurate.   Any help please would be greatly appreciated, never heard an RB26DETT before let alone driven one, and I've got a spaghetti monster of goodness to sort out.   Cheers Benny  
    • Hey all  im wondering if you can help me please I have put a rb20 box in my r34 gtt as my auto packed up and a friend had a spare box I know it’s not ideal but it will get me up and running for now. we have done the conversation and everything is working great but my Speedo we got a s13 speed sensor but my Speedo reads double now and I bought a speed converter but still not having any luck.  so I thought I’ll reach out and pick your brains  any help would be appreciated please as I wanna drive my car again 
    • Drain it. I got official Matic D but you can get whatever is listed as Matic D compatible.
    • Thanks guys,  Yeah I should at least have them dynoed, at least then I know what I've got as a starting point.  The springs on these are hard as rocks. I vaguely remember Russman saying he was going to sell the shocks to me with the rocks fitted, as he was keeping the softer springs for his new setup.  I didn't click at the time but of course that was to let me know the shock/spring wouldn't be matched.  I also remember pricing up new springs around 2014-15, but, house, money etc. it never happened. So that was another reason to have them rebuilt. I have rebuilt the forks on many motorcycles so I think I could handle the seals on these easily enough, but getting the valving right would be a rabbit hole I cbf exploring.  Duncan, interesting to hear RP was tuning these back then. I might give them a call.  In the mean time I have been busy fitting sway bars. The Whiteline rear sway bar I purchased 15 years ago finally got fitted, along with the Whiteline front bar that showed up last week. Just waiting on new links for the front sway bar to finish that off.  And my spare set of advan AVS VS5's should be back from the powder coaters in a Pearl White finish sometime this week, with a set of Hankook RS4's lined up for fitting.  And then I just have all the suspension bushes to do. A comprehensive kit is on the way... Lots to do before the Ararat hill climb. Cheers guys 🍻   
×
×
  • Create New...