Jump to content
SAU Community

Recommended Posts

just reading this other thread about how long people warm up their cars b4 they start driving...

i was wondering how long people leave their turbo timers for?

and also how did u by pass ur immobolizer or u just wait around?

i normally set mine on 15secs after normal driving around and about a minute if i gunned it : abit.

i got the Mongoose 3point alarm imobilizer which work in conjunction with my turbo timer.

Link to comment
https://www.sau.com.au/forums/topic/79152-how-long-u-cool-down-for/
Share on other sites

I look like a fool because i cant lock my car untill the engine shuts off. Im just hanging around my car for 30sec untill it turns off. I would use the Auto feature on my TT if i could lock the car and leave it. Auto normally does around 4 minutes...

15 minute warm up jesus you will be causing more wear on the engine then doing good i reckon. i normally let it warm up for a minute or two then just keep the rev's under 3K and try to keep off boost as much as possible till the oil preasure starts to drop down to the wamr level.

i warm my car up for 15min and leav turbo timer on for 5, neighbours get the shits but hey what can you do. my theory is if they complain smash their windows, if they call the cops get your mates to burn their car.

thats too ridiculous for words

anyway getting back to planet earth

as said before

dont drive hard for the first 5 or the last 5

my tt is always set for 10 seconds

i warm my car up for 15min and leav turbo timer on for 5, neighbours get the shits but hey what can you do. my theory is if they complain smash their windows, if they call the cops get your mates to burn their car.

That's ridiculous.

15 minutes is too long

5 minutes is too long

If they're windows or car was smashed they'd narrow it down to the knob who's car is always running with no-one in it.

15 minute warm up jesus you will be causing more wear on the engine then doing good i reckon. i normally let it warm up for a minute or two then just keep the rev's under 3K and try to keep off boost as much as possible till the oil preasure starts to drop down to the wamr level.

cool down here not warm up...

so most people wait around till their TT turn off before locking the car?

i agree with what others have said in terms of cool down really a turbo timer may not really be required if you just drive normally for the last 5 minutes or so. I have a turbo timer though for the times that i am in a bit of a rush its set to i think 30 - 40 seconds.

Its crazy to be running the car so hot up until you stop that you have to use a turbo timer at all. Its not just your engine, you need to think about brake temps warping rotors etc.

Just drive it slowly for the last 60 sec of your trip, lcok the car and wander off.

The only time a TT should be used is when you have just finished a session on a race track.

My car has done over 100,000km i dont have turbo timer and never let it cool down if ive been driving normally, if ive given it a hit then come to a stop (hardly ever happends) ill give it a couple of minutes. everything still seems to be fine! I agree just take it easy for the last minute or 2 of your drive.

So far just been taking it easy for the first 5 till the car warms up and the oil pressure evens out @ 2kg/cm^2.. than at the end I tend to take it early coming back into my place..

also - what's oil pressure meant to sit on.. i'm guessing about 2kg/cm^2 normal cruising, than when I boost for a bit heads up toward 4kg/cm..

anyways - yeah take it easy for the last couple of minutes.. + get a minute or so while I open the garage door..

tt's are dangerous in my opinion...

what are you guys going to do if someone t-bones your car at high speed, and your sitting there trapped in your car unconscious....hey the ignitions been killed, but the cars still pumping fuel....

I personally dont want to be burnt in my car, so i chose not to use one...same goes if you roll the car and the fuel lines are cut/broken.....pumps fuel out still.....

Just dont drive on full boost for the last couple of minutes of your trip and you won't really need to let it idle down.

If you run an oil cooled only turbo such as a TO4 or something then letting it idle/cool down is more critical.

The standard turbo's and most other modern turbos are watercooled, so excess cool down is simply not required.

My turbo timer hits a maximum of 3:20 using full auto mode and that's travelling long distance sustaining 110km/h+. Usually it will run for around the 1:30mark after some spirited, some normal. Mine's integrated into my alarm so i can lock the car with it running and walk away. No dramas.

tt's are dangerous in my opinion...

what are you guys going to do if someone t-bones your car at high speed, and your sitting there trapped in your car unconscious....hey the ignitions been killed, but the cars still pumping fuel....

I personally dont want to be burnt in my car, so i chose not to use one...same goes if you roll the car and the fuel lines are cut/broken.....pumps fuel out still.....

Thats why you hookup the handbrake sensor circuit.

That way if the handbrake isnt engaged and you turn the car off, the turbo timer doesnt operate.

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • Johnny is sad now... Because you didn't get Bosch Motorsport ABS.  
    • Hey keep the ideas coming, I'm always keen on projects! But, problem fixed!  I got a cheapie ozito scope from Bunnings and had a good look in and around the bearing and sensor hole. I couldn't see a smoking gun but the bearing looked a bit strange, especially when comparing with a new one. I thought the cover had come off the bearing magnets.  Sorry for pics of a screen, I didn't have an SD card.     Good thing I had the old one to inspect. So, given I'm like a pit crew with wheel bearings and luckily I had a spare bearing because I f**ked up my parts order, I decided to just smash it out. Got the old one out in about an hour. So much easier when the parts haven't had a chance to rust together yet. 😂 And, well, found the problem.    In the second pic at about the 8 o'clock position, you'll see what I think is the tip of the old sensor.  The new sensor has definitely been rubbing but it's all intact, just a little shiny so I'm hoping it's fine.  The car brakes perfectly now and no errors.  I think the job took about 2.5h in the end. 👍🏻 I really appreciate the help in here as usual. Thanks guys.
    • I was only looking because I saw some drops on the ground but it wasn't alot. Recently had it serviced will ask the mech to confirm. Find it strange that it looks standard though, can see in another photo of a random box 
    • So...not sure if you know if that has always been there or why you went looking. It could be old damage from a clutch explosion, or even just the gearbox got dropped somewhere along the line. Basically, you should seal it up to stop oil and dust getting into the bellhousing, but it doesn't matter too much and is not structural. I'd suggest something like a glob of JB Weld. BTW what gearbox oil are you running, I would guess the breather has been spewing it everywhere.
    • Hey Duncan thanks for your reply. Sorry mate I know the photos are shit.  Took another photo for reference. Seems the casing does have a hole in it looking on the net, fluid seeping out. Added a photo   
×
×
  • Create New...