Jump to content
SAU Community

So Everyone Knows SAU Vic Made It Into The Latest Speed Magazine Right?


Recommended Posts

just reading the latest speed magazine now. There is a article called "Monster Party" with our GOR cruise in there.

ppl who made it in were Robin-32 GTR, James (Golgo)33GT-R, Jack 33GT-R, Ash R31, Adz 34GTT, Pete34GTT and Andrew 34GTR.

A pretty good article so check it out guys.

  • Replies 58
  • Created
  • Last Reply

Top Posters In This Topic

2nd'ed - share with us poor people stuck at work!!!

congrats guys great read !! GOOOO SAU !!!!!!!!!

my car is on page 84-86, i cant belive it took 7months for it to finially come out in the mag, the car isnt even the same n e more, then they got my name wrong its JAMES DAMM IT NOT JASON !!!

Would like to pass on thanks to Joel Strickland who did all the photography work and came along for the journey.

It was to his credit that we are in there.

Thanks Joel, from SAU-Vic Committee

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now



  • Similar Content

  • Latest Posts

    • I saw you mention this earlier and it raised a red flag, but I couldn't believe it was real. Yes, the vacuum signal should vary. It is the one and only load signal from the engine to the ECU, and it MUST vary. It is either not connected or is badly f**ked up in some way.
    • @Haggerty you still haven't answered my question.  Many things you are saying do not make sense for someone who can tune, yet I would not expect someone who cannot tune to be playing with the things in the ECU that you are.  This process would be a lot quicker to figure out if we can remove user error from the equation. 
    • If as it's stalling, the fuel pressure rises, it's saying there's less vacuum in the intake manifold. This is pretty typical of an engine that is slowing down.   While typically is agree it sounds fuel related, it really sounds fuel/air mixture related. Since the whole system has been refurbished, including injectors, pump, etc, it's likely we've altered how well the system is delivering fuel. If someone before you has messed with the IACV because it needed fiddling with as the fuel system was dieing out, we need to readjust it back. Getting things back to factory spec everywhere, is what's going to help the entire system. So if it idles at 400rpm with no IACV, that needs raising. Getting factory air flow back to normal will help us get everything back in spec, and likely help chase down any other issues. Back on IACV, if the base idle (no IACV plugged in) is too far out, it's a lot harder for the ECU to control idle. The IACV duty cycle causes non linear variations in reality. When I've tuned the idle valves in the past, you need to keep it in a relatively narrow window on aftermarket ecus to stop them doing wild dances. It also means if your base idle is too low, the valve needs to open too much, and then the smallest % change ends up being a huge variation.
    • I guess one thing that might be wrong is the manifold pressure.  It is a constant -5.9 and never moves even under 100% throttle and load.  I would expect it to atleast go to 0 correct?  It's doing this with the OEM MAP as well as the ECU vacuum sensor. When trying to tune the base map under load the crosshairs only climb vertically with RPM, but always in the -5.9 column.
    • AHHHH gotchaa, I'll do that once I am home again. I tried doing the harness with the multimeter but it seems the car needed a jump, there was no power when it was in the "ON" position. Not sure if I should use car battery jump starter or if its because the stuff that has been disconnect the car just does send power.
×
×
  • Create New...