Jump to content
SAU Community

Recommended Posts

  • Replies 61
  • Created
  • Last Reply

Top Posters In This Topic

I'd take the Chaser, but I'm a big fan of R34 sedans too.

looks - about the same. I think they both look awesome, but in different ways. The Chaser is more of a luxury look, whereas the R34 is sportier.

performance - JZX100, but only just. 378Nm from 2400rpm versus 343(s1)/363(s2)Nm at 3200rpm is just in the Chaser's favour.

fuel economy - about the same I think.

potential - not sure what you mean here, but both engines are highly moddable if that's what you meant.

reliabilty - Toyota quality :P Nissan are good too, so I'd say about the same.

One big thing for me was resale price. Sedans often sell for a lot lower if they have a coupe equivalent. There's no coupe Chaser, so I'd say it would hold its value just a bit better. Then again, they cost more to buy in the first place, so it probably evens out.

I'm amazed nobody has compared the interiors yet :)

Here's a pic of mine. The original pics from Japan were terrible, so I thought it the series 2 JZX100s were pretty much the worst interior you could get in a car, but when I sat in it for the first time I changed my opinion very quickly.

The carbon fibre is very nice and suits the car really well, and the seats have a nice feel to them. The pattern on them isn't too special, but it's a lot nicer than I first thought.

A manual R34 Sedan weighs 1430kg and a manual JZX100 Chaser weighs 1480kg, so there's a good 50kg difference. I think the extra 35Nm and torque lower down the rev range would pretty much even it out.

Handling wise, I have no idea. I've never driven an R34 (or my own Chaser for that matter :))

EDIT: The autos are a different story. R34 = 1450kg, Chaser = 1490kg, but the auto R34 only has 333Nm. So if you're after an auto one, go the Chaser.

Chaser is hot Shane, but the R34 with the Eastbear GT-R front/kit will look damn insane and I think, in the same colour as the chaser, will turn a shitload more heads... if that's what you want!

Who can not gawk at an R34 GT-R when you see one on the streets? They have so much street presence that's for sure.

It's a little unfair to compare those two cars, as obviously they have had tens of thousands of dollars thrown at them. You'd really have to compare stock look to stock look, and I think the R34 has the edge there as look different to most cars out there.

The chaser has many cues to other cars out there. Many might not even draw an eye unless you know what you are looking at. I've seen a couple of stock looking ones out there, and often hard to distinguish it from a Camry from a distance (the ultimate insult! sorry :D)

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now



  • Similar Content

  • Latest Posts

    • Hi, SteveL Thank you very much for your reply, you seem to be the only person on the net who has come up with a definitive answer for which I am grateful. The "Leak" was more by way of wet bubbles when the pedal was depressed hard by a buddy while trying to gey a decent pedal when bleeding the system having fitted the rebuilt BM50 back in the car, which now makes perfect sense. A bit of a shame having just rebuilt my BM50, I did not touch the proportioning valve side of things, the BM50 was leaking from the primary piston seal and fluid was running down the the Brake booster hence the need to rebuild, I had never noticed any fluid leaking from that hole previously it only started when I refitted it to the car. The brake lines in the photo are "Kunifer" which is a Copper/Nickel alloy brake pipe, but are only the ones I use to bench bleed Master cylinders, they are perfectly legal to use on vehicles here in the UK, however the lines on the car are PVF coated steel. Thanks again for clearing this up for me, a purchase of a new BMC appears to be on the cards, I have been looking at various options in case my BM50 was not repairable and have looked at the HFM BM57 which I understand is manufactured in Australia.  
    • Well the install is officially done. Filled with fluid and bled it today, but didn't get a chance to take it on a test drive. I'll throw some final pics of the lines and whatnot but you can definitely install a DMAX rack in an R33 with pretty minor mods. I think the only other thing I had to do that isn't documented here is grind a bit of the larger banjo fitting to get it to clear since the banjos are grouped much tighter on the DMAX rack. Also the dust boots from a R33 do not fit either fyi, so if you end up doing this install for whatever reason you'll need to grab those too. One caveat with buying the S15 dust boots however is that the clamps are too small to fit on the R33 inner tie rod since they're much thicker so keep the old clamps around. The boots also twist a bit when adjusting toe but it's not a big deal. No issues or leaks so far, steering feels good and it looks like there's a bit more lock now than I had before. Getting an alignment on Saturday so I'll see how it feels then but seems like it'll be good to go       
    • I don't get in here much anymore but I can help you with this.   The hole is a vent (air relief) for the brake proportioning valve, which is built into the master cylinder.    The bad news is that if brake fluid is leaking from that hole then it's getting past the proportioning valve seals.   The really bad news is that no spare parts are available for the proportioning valve either from Nissan or after market.     It's a bit of a PITA getting the proportioning valve out of the master cylinder body anyway but, fortunately, leaks from that area are rare in my experience. BTW, if those are copper (as such) brake lines you should get rid of them.    Bundy (steel) tube is a far better choice (and legal  in Australia - if that's where you are).
×
×
  • Create New...