Jump to content
SAU Community

Recommended Posts

bigger booster to suit the 4 spot front brakes on the WGNC34?

Stock setup would probably have been fine - BM50 m/c but I have fitted a GTR one BM57 which will have slightly less travel but require more effort. Auto booster should be fine.

So is it worth getting a brake stopper for the M35? They're not exactly cheap...close to $200 for a big hunk of metal...

i was talking to scott about it.. actually doesnt seem to hard to make one.. maybe we will..

So is it worth getting a brake stopper for the M35? They're not exactly cheap...close to $200 for a big hunk of metal...

Get someone to push on the brake pedal, while you look at the firewall flex behind booster; I reckon it would be a worthwhile addition.

It could likely be done for less; might have to take a look.

Does anyone know if there is any difference between a Stagea Series 2 and a GT-t brake master cylinder.

They list different part numbers but both appear identical and are both BM50's?

I have searched previous posts from Darrin after his GT-t brake upgrade but I haven't found any information on potential differences.

Does anyone know the reason for an early DTV (disk thickness variation) on M35 brakes? Apparently a few people have had this problem already...

Thinking of putting new pads, machine the discs and check that the brake hub is not causing this...

Has anyone done all that and had the problem happening again?

Thanks in advance...

I'm trying to decide whether to replace all my rotors with slotted ones or just get them machined. They've got enough left in them to just get them machined I think, and the rears need it badly. I've got HPX pads sitting here ready to go in, was going to try and do it all at once.

Why Waste MONEY doing that on Rear,

i did mine & couldn`t tell difference in stock to GTR setup ,

with fronts just get Sloted rotors & braided lines good pads & BRAKESTOPPER,

you spend $300+ on calipers & another $300+ on Rotors ,& still need to pads LINES & brakestopper ,so $10000 on brakes lol.

i spent $500 doing all mine & VERY HAPPY ,

Fully appreciate what you're saying, but I priced up a new caliper and pads and for not much more I've managed to find some R33 GTST brembo discs, ferodo pads(both with about 1000miles use) and good used gtst calipers. I've already got a 330mm front discs conversion and DS2500 pads with R32GTR calipers. I was never expecting a great increase in stopping power from the rears but every bit helps.

I bought mine from a group buy but I can't remember who organised it.

According to the Cusco website they list the R33 same part number as WGNC34 but different from WGC34 (2wd) so R33 one should fit.

http://www.cusco.co.jp/en/pdf/Brake%20master%20cylinder%20stopper_nissan.pdf

Pretty sure I sent you the UAS stopper Bob.

I'm looking at getting new disks for my car, rather than seeing if I can machine the standard ones.

Just wondering what other people are running?

GSL supply RDA and DBA rotors, and looking at DBA, probably in either slotted or cross drilled.

Obviously the more you spend the better performance you're going to get, but I think with most things you get to a point where spending more money isn't worthwhile on a road car.

I've always heard that cross drilled rotors are a bad idea for street use, but DBA say this is no longer the case, and they've found the same or increased pad life with their new cross drilled XS rotors.

Like to hear other peoples experiences, although I'm pretty sure any decent slotted rotor will be fine.

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now



  • Similar Content

  • Latest Posts

    • Yeah well per the video it took 15s for the stock unit to start up....even if I give it a few seconds discount for starting that is at least 12 sec before you get a reverse camera if you are trying to leave a park.  The android unit is way faster, but 2016 for the stock unit is a long time ago in consumer electronics
    • Yea that’s why I said ima test them with multimeter and see the reads.
    • Only at idle. Isn’t a problem when rev it seems.
    • @Haggerty This seems silly to ask, but are you confident in your ability to tune the Haltech?  
    • Next on the to-do list was an oil and filter change. Nothing exciting to add here except the oil filter is in a really stupid place (facing the engine mount/subframe/steering rack). GReddy do a relocation kit which puts it towards the gearbox, I would have preferred towards the front but there's obviously a lot more stuff there. Something I'll have to look at for the next service perhaps. First time using Valvoline oil, although I can't see it being any different to most other brands Nice... The oil filter location... At least the subframe wont rust any time soon I picked up a genuine fuel filter, this is part of the fuel pump assembly inside the fuel tank. Access can be found underneath the rear seat, you'll see this triangular cover Remove the 3x plastic 10mm nuts and lift the cover up, pushing the rubber grommet through The yellow fuel line clips push out in opposite directions, remove these completely. The two moulded fuel lines can now pull upwards to disconnect, along with the wire electrical plug. There's 8x 8mm bolts that secure the black retaining ring. The fuel pump assembly is now ready to lift out. Be mindful of the fuel hose on the side, the hose clamp on mine was catching the hose preventing it from lifting up The fuel pump/filter has an upper and lower section held on by 4 pressure clips. These did take a little bit of force, it sounded like the plastic tabs were going to break but they didn't (don't worry!) The lower section helps mount the fuel pump, there's a circular rubber gasket/grommet/seal thing on the bottom where the sock is. Undo the hose clip on the short fuel hose on the side to disconnect it from the 3 way distribution pipe to be able to lift the upper half away. Don't forget to unplug the fuel pump too! There's a few rubber O rings that will need transferring to the new filter housing, I show these in the video at the bottom of this write up. Reassembly is the reverse Here's a photo of the new filter installed, you'll be able to see where the tabs are more clearing against the yellow OEM plastic Once the assembly is re-installed, I turned the engine over a few times to help build up fuel pressure. I did panic when the car stopped turning over but I could hear the fuel pump making a noise. It eventually started and has been fine since. Found my 'lucky' coin underneath the rear seat too The Youtube video can be seen here: https://www.youtube.com/watch?v=uLJ65pmQt44&t=6s
×
×
  • Create New...